My Bluetooth service has stopped. The device, a speaker, is detected but pairing does not complete after endless scanning. Bluetooth is reported as requiring further installation. How do I do that? Driver update is greyed out.
View 4 RepliesI have been trying to test Bluetooth file transfer on my Lenovo IdeaPad running Windows 10. I am using an Android phone and an Android tablet to transfer a file. NOTE: Bluetooth transfer from the phone to the tablet works as expected, therefore any error in the Bluetooth stack on these devices can be ruled out.
On the Windows 10 laptop, the pairing works. I've documented the process here. The error can be seen in picture 3.
I can pair the LG Optimus G Pro with Windows 10. However, when I initiate transfer from the phone OR the PC, the transfer fails. On Android, the error is just "Transfer unsuccessful". I've posted 3 images about the error on Windows when transfer is initiated.
1) Device paired confirmation: [URL]
2) Initiating transfer: [URL]
3) Transfer failure: [URL] (Connected party did not properly respond after a period of time...)
I have a Broadcom Bluetooth USB 4.0 driver installed. How to solve this? Lenovo has not published a Win 10 specific driver for my device (Y580)
I am running Windows 10 Home version 1511 build 10586.63 on a Dell XPS L502X laptop. I have just bought a Bose SLIII bluetooth speaker. I can connect it up to the laptop no problem and it works well, however when I disconnect it I cannot reconnect them without removing the device and pairing it again. On my Android phone it is detected and automatically reconnects. Why I have to recreate the device each time I want to connect on the PC? If I do a Win+A then 'connect' and select the speaker device, it tries for a few seconds then I get a yellow message 'Couldn't connect'. When I remove the device and 'Pair' it again it connects immediately.
View 5 RepliesMy custom-built pc all of a sudden won't boot in to windows. i get the error message "reboot and select proper boot device or insert boot media in selected boot device and press a key", and i have made sure that my hdd is my first boot option. i want to reinstall windows now because that seems like the only way out, but i cant because i have no recovery usb or disc. what can i do to boot to this harddrive, that my bios detects just fine.
View 1 RepliesPlatform: HP Stream 7 Bluetooth Device: LG HBS750 headphones
The device was paired, but would not connect. I attempted to remove the device, but the tablet has been trying to "REMOVE DEVICE" for 3 days now.
I can't stop or interrupt the process.
How do I rename a bluetooth device in Win10?
View 3 RepliesI am trying to remove two old Bluetooth devices in Windows 10 that keep showing up in Device Manager. I have tried to find them in Settings> Devices> Bluetooth and remove them but there isn't an option. When I uninstall them in Device Manager they keep coming back. How do I unpair and remove old Bluetooth Devices in Windows 10?
View 1 RepliesI have multiple bluetooth speakers. I don't see any way to select which speaker (or any device, for that matter) that I wish to use. On my Android phone, I can select any of the 10-20 devices that show when I enable bluetooth. How do I do that on Windows 10 on a PC/Laptop? It seems like Windows 10 just tries to connect to the first thing it sees when you turn on Bluetooth.
View 1 Repliesi have acer aspire 4750G with intel core i5. when i upgraded to windows 10, it didn't trace bluetooth device in device manager.
View 1 RepliesI am facing a problem with the Bluetooth connectivity in my laptop(OS:windows 10). If i connect to any Bluetooth device (phone/audio), wifi becomes limited and I'll not be able to access the internet. I'm facing this problem only after upgrading to windows 10.
View 1 RepliesDo I have to sync my Bluetooth after I upgrade to Windows 10? Or will all of my device just work fine without me doing anything?
View 1 RepliesI have tried for days to remove a Bluetooth Speaker that did not install proper, I remove it try to re-pair does not pair, then upon reboot it is installed again with error. No matter how many times its removed Windows keeps re installing the device on its own.
How do you completely remove a bluetooth device, all traces so you can start fresh?
I have searched the internet for 2 days and no one has the answer yet. Not even on the MS forums
I can get it to pair and says it is paired but it says it is disconnected in the playback and recording settings dialog box. Is it possible my devices are too old the Bluetooth dongle is BT2.0 and the headset is a MotorolaT225 hands free speakerphone for my cellphone which works fine. If they are then what headset does work with win10 out of the box?
View 6 RepliesJust realised that, since I upgraded from Win 7 64 Home Premium to Win 10, it has not detected the laptop's Bluetooth device. It doesn't even feature as a device in Device Manager ... not even one with a problem.
View 7 RepliesI'm not sure if this is the right place or if it should possible be network related... but for some reason, the "Bluetooth" tile is back in my Action Center, but I have zero Bluetooth devices on or installed.
It was there after the latest build 10586, then I think the first Cumulative Update came out and it went away... I doubt there was any causal link between them... but now after a restart of the computer, the tile is back... and I don't know why.
On Windows 8. 1, I had no issues with this speaker. It's a JBL Charge. After upgrading to 10 it worked fine until a reboot when it failed to connect (it pairs, but won't connect, and the speaker doesn't appear as an audio-out option in Sound settings).
The Bluetooth wizard in PC Settings says "Driver error" next to the speaker icon.
Poking around in device manager, I see this error:
"This device cannot start. (Code 10)
{Conflicting Address Range}
The specified address range conflicts with the address space."
The only references I find to this error online are for different (and quite old) version of windows, and seem unrelated to Bluetooth.
I can't even look at the "resources" tab because it appears to have vanished in Windows 10!
On initial start up had notice to check and repair c drive. It is now stuck at 67% completion and now I am unable to start windows. How can I stop the scanning? I managed to get into the diagnostic pages by pressing the space bar on the start up but non of the action allow me to sttop the scanning process.
View 5 RepliesDefender keeps asking me to quick scan my system like every couple hours or so.. Just started happening today.
View 4 RepliesAfter upgrading to Windows 10, the scanning on my HP printer doesn't work. The other printer functions work o.k.Should I simply delete the printer and reinstall it?
View 1 RepliesThis is the event error after attempting to do a regular 'FIND' within the Registry. Before the Fall upgrade installed via .iso on 11/20/2015 this Find worked.
The Nirsoft Registry Scan will scan and find. I did not attempt to link to the registry from that Nirsoft tool
The last software installed was a Nirsoft My Event Viewer as a portable app 11/21/15.It had errors via ntoskrnl.exe when executed. Microsoft apps were updated automatically 11/21/15(Photos, Messaging)
These are the only changes since the fall upgrade Win10-1511
Would this be corrected by a sfc /scannow?
Log Name: Application
Source: Application Error
Date: 11/22/2015 8:14:13 AM
Event ID: 1000
Task Category: (100)
Level: Error
[Code] ....
I have been patiently waiting for a period of 1 hour looking at the screen of my laptop. At this present moment, Windows is stuck 'Scanning and Repairing Drive D: 9% Complete'.
View 5 Repliesin windows 7 and windows 8 windows defender is working , we can set removable devices auto scan. but in windows 10 - defender is not having menu options to removable driver auto scan facility.
is there any solution for this, or should i want to change any registry entry to make window defender GUI to previous version of defender.
My PC completely freezes when detecting hardware changes (device manager) after about 3-4 seconds.
I've left it for 1h+ to see if anything happens over time, nothing.
Tried it in safe mode, same problem.
Removed geforce drivers, same problem
When frozen, all lights (and my screens) stay on, pressing capslock on KB doesn't turn the capslock light on/off.
The manually initiated crash still works though, that's how I got the memory dumps in the attachment (usually there is no dump at all and the only way to "fix" it is to press the reboot button several times)
the windows fax and scan utility can't start up because it can't access the documents folder, where it saves the scans.
Then I tried the windows 10 scan app. It saves by default to the pictures folder. It, too, could not save to the default location. but I discovered that I can set it to save to desktop, and that works. But it forgets my choice as soon as I close the app.
I am the owner of these folders. Why can't my apps access them? I checked documents properties, and I have full permissions.
Have just installed 10 on a spare drive and installed that drive into my Sandy Bridge and the machine is now going through an endless loop of start up.
I can hear it make some sort of noise as if something wants to go and I have again tried the machine with the old 7 install drive and the same thing is happening.
The other thing is I am not getting a RAM beep or the BIOS to come up on the Gigabyte board (DEL) have jumpered the reset pins for the BIOS but still no BIOS or for that matter any graphics.
Just downloaded the newest update for Windows 10, I was asked to restart my PC to install it, that was over 30 minutes ago, since then my PC reaches the Microsoft logo and under it, it says Preparing Automatic Repair and then it restarts and does that all over again, what am I suppose to do? I can't even get past it.
View 1 Replies