Computer Freezes When Need To Change UEFI Setting
Jan 20, 2016
It sometimes (not always) happens when I need to change a UEFI setting. When it's happening the screen turns black and the computer tries to reboot. Note that the computer does not crash to the point of a memory dump. When this happens I have to keep trying to reboot and eventually it loads the default Bios settings and boots.
I have so far replaced the memory, PSU and motherboard to no avail. Once the computer does boot, everything seems perfectly stable. I noticed a new Bios update and flashed it to my motherboard, but I do not yet know if it fixed things.
View 3 Replies
Similar Messages:
Jul 31, 2015
I am in the process of attempting to install Windows 10 on the system listed in my profile. I have downloaded Windows 10 as an ISO and transferred this to an NTFS formatted memory stick. The installation process works ok but I am having problems getting the SSD setup for UEFI mode and secure boot. what settings I need to apply under CSM to get the SSD running in UEFI mode? And if there are any other settings needed?
View 2 Replies
Nov 24, 2015
How do I change this screen? Change in non Uefi Mode? My motherboard is 5 years old. Can this be done without switching to UEFI?
View 2 Replies
Aug 24, 2015
I have had nothing but issues, since upgrading to Windows 10 from Windows 8 (64). The installation within of itself was horrible. I got the continual flash on the screen, until I was able to get it into safe mode and recovered it. Then made sure drivers were updated. However, I did not upgrade my BIOs, from the information I had seen from MSFT. Didn't think twice, since they said if you were upgrading from 8 or 8.1 that should not be an issue. The system was running stable, after I did those fixes.
About 1 week ago, after a MSFT Windows automatic patch push, My monitor started not to respond during boot up. Ran some basic troubleshooting for the monitor (Ie: check plugs, check cables, check Video card). They all seemed to work fine and my system booted up normal.
The very next day, cold booted again and monitor did same thing, it was not getting any signal from the computer. Went through the checks, after a little bit of a delay the system finally booted. I checked my BIOs settings, which were all set up normally. I locked my computer after that and did not turn off the system, the next morning, my monitor was unresponsive.
I re-checked monitor, cables and even replaced the video card. Everything is good except no signal to my monitor. I disconnected all hardware except the video card and motherboard, to see if it was an issue with my power. I took out out the CMOS battery and also disconnected power to the motherboard for about 2 hours, to try and reset the BIOs to factory. No luck.
This leaves me with 2 things left:
a) Corrupted BIOs, not loading my drivers, or
b) motherboard went bad.
Going to try a bootable USB BIOs next.
View 4 Replies
Oct 5, 2015
win10 lock screen problem. I use one of those free timer to shut down my computer after certain amount of time. I tried multiple different timers and they all work as long as I don't lock the screen. is there some setting I can change in windows to allow my timer to shut down my computer. Already played with the power settings.
View 1 Replies
Sep 7, 2015
When I try to install Windows 10 update, the installation freezes at 91% Setting configuration. (67% overall). I do not get any error message. I have tried various ways, Clean boot, Media creation tool etc. I have left the computer 4 hours in case it was not frozen, even though I could not detect any HDD activity.
The machine does not revert back to windows 7 as it says it is doing, but instead I get a black scree telling me status 0xC000000e . "Info boot selection failed because a required device is inaccessible." Looking this up it would seem to indicate the winload exe is missing or corrupt. I do not have any problem booting up my machine, normally, but was wondering, if it could be that, there is something wrong with my MBR and that is why, perhaps ( I am clutching at straws) windows 10 will not install.
The windows rescue disk, does not get me back, as when asking for a repair, there is no C drive showing, so I revert to my good old Acronis software. Without which I would be in big trouble.
View 2 Replies
Sep 7, 2015
I had a lot of files so I decided to reset to factory settings. Computer at 2% turned off, so I tryed to turn it on again,but windows refused to start, it turned off after the manufacturer's logo showed, so I decided to download windows 10 installer [URL] ..... and put it into my USB. I tryed to reinstall windows through usb port, but it needs to turn on the windows that can not be launched (possibly due to incomplete reset to factory settings that might have deleted important windows files). How can I re-install windows 10 without needing to access windows?
View 3 Replies
Oct 1, 2015
I was using Windows 8.1 and after upgrading to 10 I get regular freezes and the computer just stops sometimes. I think this is normally just after booting up. Do I need to wait five minutes for it to get going before I try and do anything?! This is not normal, my PC was fast and responsive before the upgrade.
View 4 Replies
Jan 10, 2016
I have a problem with my computer that it automatically freezes most of the time and I have to turn off the power, and when I starts the cpu again, then 1 short beep and 1 long beep occurs. Also, sometimes the computer also displays BSOD's. The most common was UNEXPECTED_KERNEL_MODE_TRAP. Also KMODE EXCEPTION NOT HANDLED , and PAGE FAULT IN NON PAGED AREA occured recently.
View 3 Replies
Jan 2, 2016
I got this new pc for christmas which came with 8.1, which I hate. So I did the free 10 upgrade but now run into many new problems. Many of my favorite programs are not yet compadible. Discs burned from previous operating systems and usb drives formated for previous OS will not boot. Simply freezes computer when I insert them O.o. Also had some random crashes and I just wanna downgrade to 7 and be done with this so I can finally start using my new pc.
I enter a windows 7 64 bit ISO burned from a friend and again it just freezes the computer on load. So eventually I borrow my friends genuine windows 7 64 bit disc, and now when I try to load it gives the message "cannot install 32 bit version on ECF system" or something like that.Would I have better luck downgrading to 8 and then trying to get 7? Why is 10 recognizing this genuine 64 bit disc as a 32 bit version??
View 6 Replies
Nov 10, 2015
The issue I am having is the computer is freezing when I am playing games or have multiple instances of YouTube open. I get no error message and have to do a hard restart of my computer. I get no error messages or any indication of what the error is. I think its a graphics driver issue, a cpu issue, or a HDD issue.
My specs
AMD 9590 processor
3 year old Seagate Barracuda 1 TB HDD
16 gb Kingston Black Fury RAM
Gigabyte 990 Motherboard
Rosewill 850 watt power supply
R9 390 graphics card
Everything is new except for the hard drive, I kept that from my old computer. I did not have this issue on my old computer.
View 5 Replies
Aug 13, 2015
So I just installed Windows10 - all works well.. installed Steam and Chrome.
I go to install new AMD drivers as well as my Logitech drivers for my G400s mouse and my computer freezes.. cant move cursor, can't ctrl-alt-del - I've tried a million times.
My PC is not OC'd.
View 1 Replies
Dec 24, 2015
my computer will randomly freeze without any warning. I've tried a lot of things to find the source of this issue, I tested my gpu my cpu and my ram, none of them are the reason. And from what I've noticed i'm not the only person with the issue and the issue seems to be common to windows 10.
View 1 Replies
Mar 15, 2016
Friend of mine bought a new computer for his son and i built it together. The specs are as follows:
HDD: Samsung 850 EVO Series 250GB
PSU + Case : Cooler Master Elite 310 Silver / Black - EVGA 500W White
GPU: Gigabyte GeForce GTX970 G1 Gaming 4GB
Motherboard: Gigabyte GA-B150M-DS3H DDR3
Memory: Crucial BallistixSport 2x4GB 1600MHz
HDD2: Seagate Desktop HDD 2TB 7200RPM
CPU: Intel Core i5-6400 2.70GHz
Fresh install of windows 10.
Everything boots up fine, i get into windows and drivers etc gets installed, then suddenly everything freezes completely, no bluescreen, no event viewer errors, just basically "stop" and nothing works.
I tested this so far:
Disabled all onboard stuff in bios, tested to reinstall the windows about 10 times, tested 1 piece of ram, 2 piece of ram, and ram from another computer, same with GPU and HDD's and PSU (basically swapped everything from another computer except motherboard and CPU, still same thing happens).
What puzzles me is that the computer works 100% fine, nothing seems wrong, then it suddenly locks completly. all temperatures are fine, all performance is up to par, everything seems in order. Games run at max fps etc (if i even manage to start em before it freezes).
View 1 Replies
Jul 6, 2015
So yesterday I installed Windows 10 on my computer via Windows update. (First went here Home page - Windows Insider Program and followed the steps) It installed normally, after it was done I got the login screen.
I typed my password and pressed "next" but my computer just froze and restarted and kept doing it.
I re-installed Windows 7 today, will probably try Windows 10 later, but not currently.
View 5 Replies
Oct 27, 2015
Since I've updated from windows 7 to windows 10, the computer occasionally freezes for about 10 to 30 seconds and nothing but the mouse pointer works.
It happens every now and then but mostly a few minutes after the computer has started and then every now and then. If it freezes in the middle of a download for example, the download simply continues after the freeze ends.
I have scanned the PC with numerous anti virus applications such as ESET NOD32, Malewarebytes and Norton.
View 10 Replies
Aug 4, 2015
I keep getting BSOD and random freezes that make me unable to use the computer, so i have to restart it and hope that won't happen again. Happens randomly, there is not an specific trigger to this. Leaving the minidump file to make it easier!
==================================================
Dump File : 080415-8234-01.dmp
Crash Time : 8/4/2015 10:48:25 PM
Bug Check String : SYSTEM_SERVICE_EXCEPTION
Bug Check Code : 0x0000003b
Parameter 1 : 00000000`c0000005
[Code] ....
View 1 Replies
Mar 31, 2016
I have the very latest Build of Windows 10 Pro, but recently I have experienced problems with my PC’s general performance – I therefore decided to Run msconfig to then uncheck some 3rd party programs under services within the System Configuration Hiding All window services first.
What is happening is that when I disable all and then go about checking the 3rd party progs one by one, the 1st attempt to tick one of the programmes the system config freezes. I have to then reboot the PC but the same thing happens if I try and attempt to do this again.
if I try the same thing but booting within Safe mode the PC does not freeze – so my question is .. can this action only be carried out in Safe mode ??
I have searched the internet for a few days now but cannot come up with an answer to this .. if you are supposed to be able to do this under normal windows start up then I have a big problem with my OS but if this is a procedure that can only be carried out within safe mode then all is well.
Attached Files : Pic.jpg 61.71KB
View 10 Replies
Jan 4, 2016
When i startup my laptop and click on an app or on windows button it highlights and then whole computer freezes. It doesnt respond to anything and i always have to close it by pressing the power button. It happened after i shut it down with the power button. After that it didnt work.
View 5 Replies
Nov 4, 2015
I have recently upgraded to Windows 10 from Windows 7, and have found 1 very annoying problem, any time a small video plays on a website in any browser my computer completely freezes. I cant move the mouse pres Ctrl, Alt Del. nothign works i have to hard reboot my PC. 1st i had thought it a video driver issue so have updated them but yet it still happens, i have played videos through Plex and have watched a few episodes of a show back to back and no problems it only seems to happen in a browser.
View 7 Replies
Dec 29, 2015
I am having problems changing my profile picture, I have looked around the internet and tried everything I could, When i try to change it I get an error saying "Setting the account picture failed. Please try again." I also cant see it on the lock screen everytime i reboot it.
View 5 Replies
Aug 27, 2015
I recently updated to windows 10. I play WoW often and lately when I get a skype call with the game on everything freezes then screen goes black. It's recovered once but typically requires me manually shutting the laptop down. It's an HP and came with 8.1. I bought it new and have had it under a year.
Wanted to add that I can usually hear sound for a while after the screen has gone black. I even continued a skype call for about 3 minutes until the sound cut out too.
View 1 Replies
Oct 11, 2015
For some backstory: I built this computer in late Feb of 2015. Over the last 5/7 months (two of which - July and August - I wasn't around to use it) and have had several issues with it since
Early March - Random BSOD relation to Shadowcopy files (reinstalled OS, issue ceisted)
Early September - Several random BSOD due to GPU drivers (uninstalling and reinstalling the drivers in Safe Mode - doing so in regular boot mode caused a BSOD - fixed this)
Late September - Single, random BSOD again. However, the computer could not get past the Windows Repair Environment (reinstalled the OS, issue ceisted)
Now - random freezing every few days to as often as once every few hours. This is my current issue. These freezes will occur suddenly and with no warning. One second I'll be watching a video, browsing, or playing a game then the next I'll be stuck. Any audio will loop constantly and the screen will be stuck at the last "frame". I've left it for as long as 30 minutes and it will not crash or bluescreen. The only option is to simply hold the Power button.
The event viewer will not have any error or warnings at the time of the freeze but will only have the error regarding the computer shutdown being forced at the time I hold the Power button. I was suggested to check for temps (all were normal) and perform a clean install of Windows 10 (I had upgraded from Windows 7). I had another hard freeze today similar to the ones I was having before. The issue is back and I'm unsure of what to do next. Is this no longer a software issue if reinstalling the OS was unsuccessful?
View 9 Replies
Jan 19, 2016
How do you change log-on password for computer
View 2 Replies
Jul 28, 2015
I have a weird error using Windows 10: I cannot change / adjust brightness at all. I have the latest updates for every drivers, programs and all, not sure why the system does this. Sometimes the screen brightness is 100%, sometimes just 50%. Not sure if the Catalyst Control Center is to blame, but I really need a quick solution, and until now I found none.
View 3 Replies
Aug 8, 2015
I have upgrade my windows 7 home premium to windows 10, but i found some problem.
Firstly, I can't change my desktop background / wallpaper, If I change the wallpaper or theme result is always blank
Secondly, if I connect to the internet my computer become slowly
This my computer specification :
Windows 7 Home premium 64bit
CPU i53210 M
Graphic card AMD Radeom 7670m
RAM 4Gb
View 1 Replies
