Drivers/Hardware :: Bluetooth Does Not Recognize / Pair
Oct 6, 2015
System Information: Asus Notebook UX303L, Windows 10, Microsoft Arc Touch Mouse Surface Edition. I just upgraded to Windows 10 (from windows 8.1) on a 2 month old laptop. On previous version there were NO problems with bluetooth. The problems started immediately after upgrade.
When the upgrade finished Windows 10 remembered all of my previous Bluetooth pairs. My bluetooth mouse (Microsoft Arc Touch Mouse Surface Edition) worked before the installation but after my system reboot the cursor no longer showed movement. The batteries are new. The mouse is acting exactly like it does when it is properly connected (lights flash, makes scrolling sounds, etc). When I checked the Bluetooth device screen it still showed as paired. I rebooted. No change. So I unpaired the device. When I unpaired the device it flashed for a second as a possible device to pair with and then was no longer on the list. Other possible devices to pair with appear and disappear from the list without cause. (Ex. sees a scanner for a few seconds then no longer has a scanner. Sometimes its up for a few minutes at most but the list is constantly flickering.) So I rebooted. Then it did not see the mouse at all. I did this for several days. Sometimes when I would turn on my laptop it would flicker, sometimes it would not.
After about 3 days with no explanation it suddenly showed up and did not flicker. I connected the mouse and it worked for about 2 days. On the 3rd day I tried again, and the cursor would no longer respond even though the mouse was acting exactly the same. I rebooted. No change. I unpaired the device and it never showed up on the list. It's flickered a few times but when I click on it to pair it pops up with an error basically saying "cannot pair. Please check and see if the device is still set to connect to bluetooth." That is only on the rare occasion that it actually shows up on the list long enough to hit pair (maybe 2 times out of 50 attempts or more.)
It is a Microsoft mouse by all means it should work on Microsoft drivers.
View 5 Replies
Similar Messages:
Aug 30, 2015
Bluetooth keyboard wont pair after windows 10 update? I tried the keyboard on other devices not running windows 10 and used it prior on windows 8.1 without any problems but now on Toshiba laptop and tablet along with an acer desktop all running windows 10 the Bluetooth keyboard wont connect.
It shows up ready to pair then i click pair and enter the numbers it tells me to and press enter then it states its connect for about a minute then just states its paired after that. even if i turn it on and off or Bluetooth on and off it only states its connect for a short time then just goes back to pair but at no time during the time it says its connected does it work. also other Bluetooth audio devices work fine without issue.
View 1 Replies
Nov 17, 2015
windows 10 november update how do i pair my phone so ill can get text on my pc from my phone?
View 1 Replies
Dec 1, 2015
New win 10 and new dirve .drive shows in 'this computer'. Cant recognize any disks. here is the event log:
View 4 Replies
Sep 1, 2015
Two days ago I got home from work and turned on my computer, which is a little over a year old and has never had any problems before. It wouldn't boot up. It said something about the ivp4 or ivp6 or something along those lines. Whatever. Anyway, I restarted a few times and eventually went into BIOS and didn't see my SSD listed anywhere... Only the ivp4, ivp6, dvd rom, and my HDD. Ok. So I reconfigured my settings, put the HDD first in the boot sequence, and restarted....
And then it said there was no boot drive. So I went into BIOS (originally I couldn't get into that... I had to put a Windows 7 boot disk into the dvd rom to even have that option) and there is no SSD and no HDD. Now when I restart it without the boot disk in the dvdrom it says, "Restart and select proper boot device". Too bad I can't. I wish I could. I unplugged the SSD and HDD and put them into a really old PC I have... It didn't recognize them. BUT... Then I took the HDD out of the really old PC and plugged it into the newer one... And it wasn't recognized there even though it's good on the other one.
Also, when I plugged in two external HDDs, they were both visible. I couldn't boot up with them, of course, but they were there in BIOS. My PC still powers on perfectly fine. I've taken the CMOS out to reset any misremembered settings there. I've set BIOS to default, played with settings, gone back to default, etc. I've configured my SATA to Raid, AHCI, and IDE. All serial ATA ports read as empty, even though they're not. I've plugged my SSD into different ports, used different cables, etc.
The only thing different about anything is that a few days prior to this, I took a plunge of curiosity and upgraded to Windows 10. I usually wait at least a year before upgrading OS's to give time for all bugs to work their way out, but for some reason I didn't this time. One lovely day my computer randomly wouldn't read my SSD. Then it stopped reading my HDD. It wouldn't read a good HDD from another computer but the other computer wouldn't read either the SSD or the HDD from the first computer. It would read external HDDs but not boot from them.
It'd make sense if my SSD and HDD just died for no reason and were bad (but why would one die and then the other a few minutes later?) but if that's the case, why won't my PC read the old HDD from another PC that I know works? Likewise, it'd make sense if my newer PC just wasn't reading any drives and they were actually both fine, but then why would it read external HDD's and why wouldn't the SSD and HDD show up on my old PC? (It's old AF... Maybe that's why?)
View 10 Replies
Feb 13, 2016
I'm having trouble to get picture on my main and only monitor when booting up. The green led indicator on the monitor is just flashing.
Usually I have to push the restart button 10-15 times until picture finally appears. Sometime I am able to log on in the dark. Hit space and logon, then do a win+p until picture appears.
I've tried to uninstall the drivers, but that didn't solve it. I had to use a different monitor to get in for the first time after that. Driver is the most recent one.
View 2 Replies
Aug 18, 2015
When i go to disk management all i see is NTFS file system , my SSD no longer shows , is this normal ?
View 9 Replies
Sep 26, 2015
I'm having quite a bit of trouble removing the generic bluetooth drivers that Windows installs for you. Those have to be gone if I want to install Toshiba Bluetooth Stacks, which I need in order to use my Wii U Pro Controller in my computer. I've gone through a few methods to try this out and all have failed.
I started out by simply uninstalling the drivers on the device manager (or whatever it is called in English). Didn't work, as the drivers were back when I had to plug in my dongle to complete the installation for TBS. When I tried this in Windows 7, it worked flawlessly, yet in Windows 10 this method did not work.
Afterwards, I tried deactivating the forced driver signature, as well as make it so Windows Update doesn't automatically download any drivers it finds suitable. On top of this, I traveled into the INF folder of my Windows folder to do steps that Microsoft recommended: rename bth.inf to bth.inf.old and bth.pnf to bth.pnf.old. With all this, it should in theory work right? Nope, it didn't. Not even after a reset.
My last attempt involved unplugging my PC from the Internet as a first step, followed by everything else listed above and then a reset. The drivers were still back, bth.inf and bth.pnf somehow magically appearing in my Windows folder when I have no Internet access. I'm at a loss as to what I'm supposed to do.
View 4 Replies
Aug 19, 2015
So, I downloaded Windows 10 a week ago, and checked for updates, but no driver updates came up. But I know that my Video Card was out of date, as I kept getting an error and also, my Bluetooth is not working. Hence my point, is there any third party app that allows you to download and update drivers?
View 4 Replies
Sep 27, 2015
Ever since the transition to windows 10 the dvd drive will not recognize,read or view any disc i put in, it says please insert a disc into drive E:. However my brothers laptop can view,recognize and read the disc.
View 9 Replies
Aug 27, 2015
I am fixing my corrupted PlayStation 3, but my computer does not recognize it's HDD so I can not fix it.
How can I make my system know that I have an HDD plugged in?
View 8 Replies
Aug 9, 2015
My computer with Windows 10 no longer recognizes my Hero 3+ GoPro Camera, nor my Nikon D5100. I have looked for drivers, but to no avail. Any way that I can pull pictures/video off these devices and put on computer?
View 13 Replies
Nov 21, 2015
After installing Windows 10 (I had 7 before), my computer does not recognize the D: Drive at all.
I have a Lenovo H410 Desktop (Lenovo Windows 7PC).
My scans show that all my drivers are updated, but there does not seem to be a driver for the disc drive.
Is that what I am missing? If so, where I obtain it? I have tried the Lennovo website, but am having some trouble getting to the drivers.
View 2 Replies
Oct 31, 2015
I got a new Samsung SM951 M.2 PCI drive. I have a X99 motherboard but it didn't have the M.2 slot so I purchased an adapter to attach the drive and installed it into an open PCI slot.
When I first installed it and boot up under the current Windows 10, I could see the drive through Disk Management.
I disconnected the current Windows 10 version, put in the disk, booted up and selected the drive to perform a clean install. The initial copy and prepare for installation worked fine, then it needed to reboot and that's when I got the message:
Internal hard drive not found
No bootable devices
When I reconnected the old hard drive and booted up, I could see the install files on the new drive, but it just won't boot to it.
So, what do I need to do to get the PC to recognize this drive as bootable?
View 3 Replies
Dec 12, 2015
Early on in the Windows 10 update process, I was able to upgrade an HP Stream 7 and a Stream 11 to Windows 10. Both had the same 32GB RAM and nominal 32GB eMMC as the Stream 14 I am wrestling with. Both came to a point where they told me the device had insufficient space on its C: drive. In both instances I selected an external Micro SD drive, and off it went with the upgrade.
In this instance I cannot get past that point. I select the external drive (a 320GB external USB spinner) but it doesn't accept that or any other external device I offer it.
When I click "Refresh" it says that it needs 10GB on C: drive, and eventually says that the upgrade failed.
The computer has been wiped, and reset to factory spec for W8.1 with all updates installed. It has ~20GB on C, and 7GB in another partition, so even if I find a way to remove the partition it wont be enough.
I'm about to have to give up on this thing and just make the poor user run with W8.1 until further notice, how to get past this point.
View 1 Replies
Jan 13, 2016
Went thru iTunes support. Can't get windows to recognize my device
View 3 Replies
Dec 20, 2015
Recently I purchased a Logitech h151 headset which has only one single jack, as my ASUS laptop has only one jack used for a headset. However, upon connecting the headset, although the sound plays through it perfectly and without issue, the microphone doesn't seem to work.
I've tried multiple solutions - I went to the Realtek Audio Manager to try and find advanced options, as I read that a possible fix to this is to go there and select an option to separate all input jacks. However, I cannot seem to find advanced options anywhere. I have also entered the Sound section in the control panel, and under the microphone section my external microphone was not detected, even after showing all disabled devices.
As for the Realtek Audio Manager issue, I read of several solutions to make advanced options pop up - from updating the driver to completely uninstalling it and such. As you can probably understand, I would rather not result to such things as messing with the drivers, as I am not a tech-savvy person and will not be able to claw out of a technical hole should I get into one.
EDIT: I forgot to mention, the internal mic is being used and can be detected (of course).
View 5 Replies
Feb 16, 2016
I recently bought a new laptop with Windows 10. My previous laptop had Windows 7 and worked very well with my Brother MFC-J475DW Wireless Printer. I tried installing the driver for the printer from the original disk that came with the printer on the W10 laptop several times and kept getting a message that there is no printer. I went to the Brother website and downloaded the latest version of the driver and still get the same message. After some research I tried for the "built in" drivers, but with no success.
View 5 Replies
Aug 3, 2015
I have followed several similar threads and their fixes for this problem with no result. After downloading the Win 10 upgrade, my system then said "loading updates". Then it restarted with a blue login screen saying "Welcome Back!" And a box to enter my password. The cursor is blinking in the box, but neither my mouse or keyboard works.
I have hard booted several times since the ctrl+alt+delete does not work. I am also not able to access safe mode as none of the "F" keys work during boot up.
I have tried the following:
1. Unplugged all USB devices except keyboard.
2. Turning off internet at the router.
I have a Dell desktop, and upgraded from Windows 7, with a Netgear router/modem. The only way I can get the system to move is if I power off at the main switch after booting up which goes into bios and disc diagnostics, but I don't know enough about computers to know what to do there!
View 9 Replies
Aug 28, 2015
What I do know is that before I upgraded to Windows 10, there was always a box under (what is now) the heading "This PC". If I connected anything to the computer via a USB cable the computer would automatically recognize it and I would be able to transfer files.
Basically, I have a USB cable that I am using to connect my Samsung Galaxy S4 to my computer, an Acer Aspire. When I plug them into each other nothing happens. There is no pop-up window on my computer that even registers that the device is connected. I've tried multiple times to click the "This PC" button to see if the phone is connected, but it actually seems to be reading other devices around me and asking if I want to connect to them.
I would have used Cortana to ask, but unfortunately I'm having a serious problem with the fact that every single little thing I want to do from the desktop (you know, all the cool new apps or whatnot) requires me to sign into my microsoft account. Unfortunately for me, I created my account so long ago that the verification email they send your forgotten password to I have actually been locked out of because I don't know the password for that, and cannot have the security code sent to my phone since they have a very old number.
View 4 Replies
Aug 19, 2015
My laptop does not want to recognise the sound card/audio driver that are built into it. The fun part is this just happened. Audio played yesterday, and the time before that, and even before the upgrade. The only thing that has changed (or at least is the biggest change i can think of) is downloading and installing Cygwin (sans audio packages). In trying to play a song on the new microsoft Groove, i get this;
Further inspection in the playback devices, the only two options are the Speakers/Headphones and communications Headphones, the former of which i can only assume is my actual computer speakers (otherwise its completely gone!).Looking at the device manager, everything seems okay. All the drivers are up to date so im not sure what could be wrong there?
Its Windows 10 pro (upgraded from Win7 Pro) and the computer is a Dell Precision M4600. (I am pretty sure the audio driver is in the device manager image).
View 1 Replies
Jan 27, 2016
I upgraded to windows10 from 8.1 and now do not have bluetooth drivers
View 2 Replies
Aug 7, 2015
It says my PC is searching for other devices under the Bluetooth menu, but there is not a switch saying on/off.
View 9 Replies
Feb 10, 2016
I am using a desktop PC that does not have any Bluetooth devices, but Bluetooth is shown as on in the notification center. If I click on it there, it guides me to settings>devices, but there is no Bluetooth option there. I checked device manager and I do not have any Bluetooth devices and I have checked my Ethernet adapter settings and there is also no Bluetooth device there.
I have a second PC which also does not have Bluetooth and it does not appear in that one's notification center.
how to make it go away on my main PC?
View 2 Replies
Nov 2, 2014
Dell WLAN bluetooth driver is not installing on my laptop . I found out that the same driver is working fine on my friend's laptop and i even used same driver for windows 8.1 previously.While I install it ,it shows an error that "The installer cannot run on this platform...",,I even tried refreshing my laptop but still it didnot work..
View 19 Replies
Dec 8, 2015
I just purchased a recertified Asus Q302LA 2 in 1 convertible 13.3" Laptop which came with Windows 8 installed. When I upgraded to Windows 10, shortly after I got it, the Bluetooth would not function. It did function with the Windows 8.
On the "System Information" page I found at System Summary>Components>Storage>Problem Devices, this entry: Microsoft Bluetooth Enumerator LE Device
BTHMS_BTHLE9&d0f185d&0&0
This device cannot start.
I also found when double clicking on Microsoft Bluetooth Enumerator LE in the Device Manager, and getting the "Properties" box; an entry for "Device Status" under the "General" tab that says: This device cannot start (Code 10) STATUS_DEVICE_POWER_FAILURE
Also, under the "Events" tab in the "Properties" box there is an entry under "Information" that says:
Device BTHMS_BTHLE9&d0f185d&0&0 requires further installation.
I have checked for driver updates and there were none. There is no "Bluetooth" icon in the "Action Center" sidebar, instead there is a "Connect" icon, but I cannot connect my bluetooth headphones or a bluetooth keyboard. Just get the message "No Devices Found".
I have the only two services for "Bluetooth" on the Services page "running" with "Automatic" start. I did not find an entry for the Microsoft Bluetooth Enumerator LE.
View 3 Replies
