I am trying to install intel RST (rapid storage Technology) to try to restore my once blazing fast laptop.
Not that it works anyway but the setup keeps asking for .net framework 4.5
But windows comes with .net framework 4.6 & 4.5 and below.
So I tried disabling the windows one and re downloading it and that didnt work, it says already installed. How do I get around this?
New build. From a fresh install of windows 10 i try to install the drver for my IGPU Intel HD 530. each time i do that i get a BSOD with this message:
VIDEO_TDR_FAILURE igdkmd64.sys
Or sometimes it's
SYSTEM_THREAD_EXEPTION_NOT_HANDELED igdkmd64.sys
I've tried drivers from motherboard manufacturer CD, website and intel and some autodetect driver software. I always get the same behavior:
The screen start blinking several time ( black screen) before showing the BSOD then reboot and repeat it self. Even the driver downloaded by windows update have the same impact.
I've managed to install it in safe mode but when i restart in normal mode i get the same behavior.
I've tried 2 different monitors, VGA and HDMI , tried with UEFI on/off => same result.
I've tweaked once the tdr delay to 8 second, but didn't work.
CPU: Intel I7-6700KMotherboard: ASUS Z170 PRO GAMING
RAM: HyperX FURY HX421C14FBK2/16 - 16Go Kit (2x 8Go) 2133MHz DDR4 Non-ECC CL14 DIMM
SSD: Samsung EVO 850 MZ-75E250B/EU 250 GB
with 80 PLUS 550W power supply.
OS: WINDOWS 10 FRENCH HOME X20-25432
I very briefly switched on the IGP whilst swapping from Nvidia to AMD last month and now Windows Update is constantly trying to update (and failing) the drivers even though no Intel drivers are currently installed, I used DDU to remove the Intel and Nvidia drivers.
How to stop it? Now whenever I open Windows update I get updates are available for Graphics Adaptor WDDM1.1, 1.2 and 1.3 for Intel HD Graphics 4600
I can't even search for new updates any more!
I very briefly switched on the IGP whilst swapping from Nvidia to AMD last month and now Windows Update is constantly trying to update (and failing) the drivers even though no Intel drivers are currently installed, I used DDU to remove the Intel and Nvidia drivers.
How to stop it? Now whenever I open Windows update I get updates are available for Graphics Adaptor WDDM1.1, 1.2 and 1.3 for Intel HD Graphics 4600
I upgraded both my desktop and laptop to Windows 10 recently. The desktop's upgrade went smoothly; NVIDIA already has Windows 10-compatible drivers. However, my laptop with Intel HD Graphics is a different story. I've tried the Dell-certified drivers as well as the latest ones directly from Intel, and neither work.
When I attempt to install the driver, I get an error message stating "This computer does not meet the minimum requirements for installing the software."
I get the message this computer does not meet minimum requirements. I have gtx 970 with latest driver and I installed latest drivers from mainboard site. My motherboard is asrock z97 fatality killer. My cpu is i5 4460.
View 1 RepliesI have a laptop with an intel AC 7265 wireless adapter built in. With the normal Windows 10 driver, AP mode works - which I need to run Connectify.
I upgraded to the latest Intel driver as I was having other issues (Wireless would just disconnect and give me a 1609 address) but the new driver apparently doesn't support AP mode (hosted network support = no).
How I can get AP mode supported again?
I have an Acer Aspire E5-571 and am trying to switch from the graphics driver provided by Acer to the newer version for my graphics card available directly from Intel. The card model is HD Graphics 4400 and the CPU is a 4th gen Core i5 so I'm pretty sure this is the correct driver.
I have tried uninstalling the graphics driver through the Windows Device Manager, then rebooting and installing the driver from Intel, but I continually get the message about my computer having a customized driver from the computer manufacturer. It seems that as soon as I uninstall the driver, it is immediately reinstalled by Windows, thereby not giving me the chance to switch to the Intel driver.Is there a way to manually switch to Intel's driver?
I have an ASUS e56u laptop that I updated from Windows 7 to 10. Since the update the -Intel(R) Centrino(R) Wifi N-6150- driver is not starting up. It is the newest version (ver15.12.0.9).
View 2 RepliesI updated W7x64 to W10 Pro x64. The machine is WXP generation notebook. My problem is that the Intel PRO/Wireless 3945ABG is not recognized or Network and Sharing Center - Change Adapter Settings does not list this adapter. The Device Manager does show the adapter but with exclamation mark. What I have done so far are uninstalling/reinstalling the adapter and installing the drivers in compatibility mode.
View 6 RepliesUpgraded Win 7 Pro Dell laptop to Win 10 Pro. Screen resolution changed on first win 10 boot and other resolutions greyed out. Windows update says unable to update Intel HD graphics drivers. Downloaded win 10 drivers from Intel site and installed. On reboot get continual bsod as above. No restore point since upgrade. Can't boot to Windows. how to get past the bsod
View 1 RepliesI'm using Win10 x64 and Intel 520 240GB SSD:
For my mobo, Asus P8Z77-V-Deluxe, I downloaded the official asus chipset drivers.
There is one for Win8.1 x64 and a Beta version for Win10.
The chipset driver for Win8.1 has installed the following:
1. under Device Manager> IDE ATA/ATAPI controller > Inter 7 series/C216 chipset Family SATA AHCI Controller
2. Version 12.8.0.1016 - Date 2013/08/01
If I install the Asus Win10 chipset driver, then instead of the Inel SATA controller, I'll end up having Standard SATA controller by Microsoft.
I'm currently using the Asus beta Win10 chipset driver, however I manually installed the Intel SATA controller which is officially supported on Win8.1 and is digitally signed.
I ran two SSD benchmark test with AS SSD (latest version).
With just the official Win8.1 chipset driver as mentioned above, I'm getting the following results:
With the Win10 beta chipset driver and the Standard SATA controller by Microsoft:
And here are the test results made by Intel SSD 520 Series Solid State Drive | Intel,SSD,520 Series,Solid State Drive,SSDSC2CW240A3,Benchmarks,Performance,Reviews,Olin Coles,Intel SSD 520 Series Solid State Drive SSDSC2CW240A3 Benchmark Performance Review by Olin Coles
Can spot the difference?
I have a PC with Asus P9X79 Deluxe motherboard. It has Intel chipset and Intel BIOS RAID (RSTe) and 6 SATA ports connected to it. The chipset IDE controller lists in Linux as:
Intel Corporation C600/X79 series chipset SATA RAID Controller (rev 06),
and the PCI ID is:
0104: 8086:2826 (rev 06).
My RAID configuration is 2xOCZ-VERTEX4 256GB SSD's in RAID0, as boot drive (C: drive), and 2 (quite old) WDC WD2500KS 250GB disks in RAID0 for extra storage (games, movies etc) (J: drive).
So yesterday I decided to upgrade my Windows 7 Ultimate to Windows 10 Pro. All seemingly went well during the upgrade process, and the system booted fine, and most stuff seemed to work as it should. But after a while when I accessed files on the J: drive I started experiencing random (temporary) freezes.
Then after a while it got more serious and the whole system froze, I had to hit the reset button.
So I rebooted and looked in the event log, I get see tons of errors there saying that the disk has a bad sector.
Then I try using the J-drive again, by viewing some videos there, and it works fine, but after a while there are some freezes and then I see in the event log, that the drive was reset. After this it works again for a while but then another of those resets comes, and freezes everything for a short while (like 30 seconds).
But when I try to copy some large files off the J-drive, another reset comes, and then the event log starts showing a lot of the error messages from before, with "the disk has an bad sector". (I will post screenshots of these errors after I reboot back into Windows).
After this I can't access the J-drive at all, and Windows gives me error messages when I try to.
So, I figure that I might have just got unlucky and the old WDC drive actually developed read errors, although it's strange that it happens exactly when I install Windows 10 (these drives are something like 7 years old).
Well I can't copy the contents off the disk from Windows since it keeps failing as described above, so I boot into Ubuntu Linux from a USB stick, so I can use ntfsclone to image the J-drive to another disk. I start it running expecting that I'll start seeing read errors, but to my surprise there are NONE. It also copies all files off the J-drive without any problems from inside Linux!
So it was after all not the old drive that had failed, but instead Windows 10/Intel had failed me in a big way.
I trawled the web for updated Intel chipset drivers and installed those from the Asus site, but it made no difference at all. I couldn't find any other Intel drivers and when I searched for the RST drivers on Intel's own site, I could only find ones for Windows XP upto Windows 8.1, but none for Windows 10.
For now I'm left with a PC that I can't use, because I can't go back to Windows 7 and Windows 10 is not working with my RAID arrays. I got some spare 2TB disks, and I'm right now copying all the data from the old J-drive (the RAID1 about 500GB) over to this, hopefully I can then work in Win 10, but I am VERY concerned because the same RAID and drivers are used for my master boot drive with the two OCZ SSD's.
I get this error on a Surface Pro 3 which I have updated to Windows 10. It normally occurs when playing Minecraft, anywhere from 5 minutes to 1 hour after opening. I have attempted to update the drivers, but it says that the drivers are up to date (which is odd as I am using Windows 8 drivers on a Windows 10 machine).
View 1 RepliesI reinstalled windows 10 pro fresh and now i cant install any program of the internet. I tried everything but it doesn't work. It always said that 'cant connect to download center' .
I remembered that i was able to install opera for some reason. That program and steam. Maybe it has something to do with my hard drive cause when I tried to install skype it didn't automatically set to my hard drive.
I recently put a new SSD drive as a clean install into my Dell xps 8700. The plan was to use the HDD as a storage disk. I discovered that many programs needed to be reinstalled after the install. I'm wondering if it would be possible to retrace my steps and start over with and Migrate over the SDD with info from the HDD.
It would save me money replacing some of the programs I no longer have keys or CD's for.
Whenever I try to do anything, like install a program, open some files, I get an UAC warning saying: :"To continue, type an administrator password", but there's no textbox where I can type the password and Yes button is disabled. I found a solution on the forum [URL]..., but I can't enter Safe mode whatever I try, I never get an option to enter safe mode and I can't use msconfig cause UAC blocked it. What can I do?
View 1 Repliesi have this problem since a long time ago , and i can't seem to figure out how to fix it!
i am sick of this file, the option of "Open file location" is grayed out for it !
I have been installing and reinstalling windows 10 through bootcamp 6 on El Captain on my Macbook Pro.
But i keep getting the same result - the speakers and right click option are missing.
Where i can download drivers for Windows 10 on bootcamp 6 or what other way to resolve this issue.
Unfortunatley I am unable to install any driver for my phone; the Oneplus One. This is the error I'm getting:
"one of the installers for this device cannot perform the installation at this time"
I get the same error for ADB and Fastboot drivers.
I installed Windows 10 Pro on an Intel NUC5i3RYH. In the UEFI settings I enabled Secure Boot, enabled UEFI boot and disabled Legacy Boot, yet in Windows 10 System Information it still says Secure Boot State: Off.
Is there something else I need to do to get Secure Boot working?
I purchased a new NUC6i3SYK last week. I have installed a 250gb Samsung evo 850 M.2 HD and 1 8gb stick of Corsair PC4-17000 DDR4 Ram.
Windows 10 is a fresh purchase and install downloaded direct from MS.
The Nuc worked fine with both the HD and Ram being recognised and W10 installed fine. I loaded the drivers from the Nuc support page and then updated Windows. Everything still fine. Then I proceeded to install other programs and went to bed.
Next morning the PC had crashed and failed to restart. After searching the net for possible cause I decided to reinstall Windows 10. This time i didn't load any drivers and the PC was NOT able to connect to the Internet because I thought one of the updates may have cased the crash.
PC was still unstable and crashed often to the point it was in a BSOD loop. I then reinstalled Windows 10 again and this time I installed the LAN driver only and Windows 10 updated itself. It stayed on for 12 hours and has now gone into a BSOD loop again.
The BSOD error message changes but the main ones seem to be
Memory_Management
irql_not_less_or_equal
0xc000021a
Throughout this process I have:
Run Memtest86 for approx 20hrs with no errors
Performed a disk check
Installed samsung magician to confirm HD firmware is the current version
Updated the BIOS to current version
System: Intel NUC 54250WYKH
Monitor: Acer T232HL (1920x1080)
OS: Windows 10 Pro (clean install)
When my NUC wakes from sleep mode, existing windows are sized and positioned as if the display resolution had changed to a much lower value (e.g. 1024x768) during sleep but was restored to 1920x1080 after waking. The windows are smaller and positioned in the upper-left corner of the display. This happens with any program I have running when the system goes to sleep (e.g. File Explorer, Visual Studio 2015, etc.).
This problem didn't happen with Win8 on the same computer.
I every now and then, but lately too often, get a pop up and my screen goes black..that the intel graphics display was not working but has been restored..then after 20 seconds or so the screen comes back on...BUT, it mentions for Windows 8..I have a new PC with windows 10.
View 1 RepliesAlright, My specs:
Intel i7-4720HQ processor
nVidia GTX 960M
Intel HD Graphics 4600
Every time I start off a boot, my intel display driver fails to work. Right after logging in on Windows 10, I can clearly see that the animations are laggy and my computer isn't running on the intel HD 4600 driver. When I open up the device manager I get a yellow triangle next to the driver and I have to disable it and re-enable it, for it to work. This happens after every boot and it's annoying. Everything is up-to-date. And I tried system restore, didn't work. BIOS reset, didn't work. It's a laptop so there is no switching ports and what not.
Recently i installed Windows 10 Pro on a Laptop Compaq Presario c700 with an Intel Celeron M530 and Intel GMA 965 express graphics card,when the laptop is idle and my screen turns off after 5 minutes,the Automatic System Maintenance starts right away and for the limited graphic chipset i think, the laptop remains unresponsive, the keyboard doesn't work, so I can't do ctrl+alt+del, the mouse pointer also disappears, the only thing i could do is a hard turn off, losing all my job....
View 1 Replies