Drivers/Hardware :: Copying Files Goes Really Fast Then Slows To A Crawl
Jan 20, 2016
I just got a new 8tb external drive and this started happening. 2.5 gb file mkv..It'll have a burst of write speed completing 60-80% and then slow all the way to 0 and just trickle the rest, even though it fluctuates from as low as 5 up to 30-50mb until it's done.
View 2 Replies
Similar Messages:
Jan 26, 2016
Had this problem now since installing Windows 10 for the first time. Have re-installed 10+ times, from new downloaded ISO's with hash tag checks just to make sure. Have bought all new hardware as well; CPU, PSU, Mainboard, Computer case, CPU Fan (3 of them), problem still persists, is obviously a Windows 10 problem.
CPU Fan slows to almost halt after waking up from sleep/hibernation.
View 9 Replies
Sep 1, 2015
I have a gaming rig I bought a month ago. It wasn't set up right, so I'm formatting the drives and starting from scratch. I'm trying to copy 60GB of stuff to a external drive before I wipe it. It's been going for about 6 hours now and stuck at 99%. It says that there is 0 bites remaining, and 25 seconds. It's stuck there and won't change. Should I just cancel it, because 0 bites are remaining I assume everything is there.
View 1 Replies
Jul 30, 2015
I got my free upgrade to Windows 10 and I tried installing it. But it got stuck at 24%, copying new files 83%.
View 2 Replies
Oct 20, 2015
Is there a rugged copy program that can copy a partially corrupted file (*.mpg) from a CD/DVD onto your H/D? What happens is that when the normal windows copy operation encounters that portion of the DVD that is faulty, it tries over and over again (endlessly, it seems) and then just hangs and I have to reboot, forcing that irritating wait for it to scan the C and D drives on reboot. This occurs with any program I try that attempts to read the entire file from the DVD, such as PowerDVD, windows explorer copy, Media Player, windvd, dos copy, etc. I assume it is because a cluster with a faulty cyclic check is encountered, and the windows read operation can't just accept the data anyway and proceed, but, instead, keeps on trying to reread and getting the same cyclic error over and over again.
What I need is a read option that "accepts" the error, transfers the bad cluster as it came across (errors and all), and then continues until it reaches end of data. I get this when some of my home-recorded mpg movies hang up somewhere in the middle, but, if I know in advance and skip over the bad part, the remainder of the movie plays just fine. I need a program that will ignore the cyclic error and just go on. I know we had this back when I did mainframe programming (the ACCEPT option), so I wonder if there is any windows program that does the same for mpeg files on CD's or DVD"s.
View 5 Replies
Jul 30, 2015
I had reserved a copy of windows 10 and i was able to download it through windows update. once it is downloaded i was asked to restart for updating. copying files stuck at 0% for 5 min and windows 7 ultimate x64 rolls back.
I can even see an error message in windows update page shows Windows 10 Pro installation failed error 80070006
View 4 Replies
Jun 14, 2015
Followed the tutorial, extracted the iso. Ran set up. How long should I let it stay at 0%
View 3 Replies
Jul 30, 2015
I tried updating my Win8.1 to Win10 twice.
The first time, it hung at 26% total, 89% copying files. Then it bricked my system completely so I made a clean install of Windows 8.1. There was nothing else installed than Windows & Updates.
Tried to update it with a stick made by the Media Creation Tool --> Stuck at 23%, 77% copying files.
I tried everything: Disabled Network Adapter, pulled all Cables (only mouse left) out, I also detached my second HDD.
I am trying to install Win10 on my SSD (Samsung 830 Pro, 130GB). I am running a Z77 Chipset.
I'd love to install completely new with the Image but that doesn't work because of the activation later on..
I'm stuck with a fresh Windows 8.1 install now, that's not really what I wanted. I'd love to update to 10 since I had it as a Insider too.
View 1 Replies
Dec 17, 2015
I have made several attempts to upgrade my desktop from 8.1 to 10. Each time the install freezes at the "copying files = 3%" point. When I reboot the system returns to my 8.1 setup and shows the above code with this explanation. "Installation failed in SAFE_OS phase with an error during APPLY_IMAGE operation"
View 9 Replies
May 20, 2015
First time running into issues with my SP3. Was able to download the latest build without any issues. Restarted and the overall install is 18% (blue ring has disappeared) and the Copying Files step is stuck on 63%. Been like that for 15-20 minutes or so. Should I wait it out or try to shut my Surface off?
View 5 Replies
Jan 4, 2016
With Windows 8, if I copy files or folders from one disk to another, a window appears which shows the progress. This is very useful. Windows 10 does not show this window. Is there a way to make it appear?
View 3 Replies
Jan 28, 2016
With Win7 I used to open one external drive, then through My computer locate the other drive. I would have each drive on its own window. I could then select relevant files on one drive copy and paste into the other drive. With Win10 if I click on File explorer I can open one external drive, where can I locate the other drive to put in a separate window. If I click on the other drive, it just opens it in the same window. Win7 and previous versions used to be so simple.
View 5 Replies
Jul 29, 2015
Windows 10. I'm at the "Upgrading Windows" screen and it's been stuck at 25% (copying files 84%) for over an hour. Is this normal?
View 7 Replies
Aug 4, 2015
I have tried to upgrade from win7 to win10 after copying the files and the system restarts, I will get the error 0xc000000f. I have both win7 and win10 disks and the automatic repair would not work.
Apparently this has to to with some bios settings, I have tried to follow the guide but I do not have all the options to described in the guide below.
[Solved] Error Code 0xc000000f Windows 8: A Required device isn’t connected or can’t be accessed
Specs:
Processor (CPU)Intel Core i7 Quad Core Mobile Processor i7-3630QM (2.40GHz) 6MB
Memory (RAM)8GB SAMSUNG 1600MHz SODIMM DDR3 MEMORY (2 x 4GB)
Graphics CardNVIDIA GeForce GTX 660M - 2.0GB DDR5 Video RAM - DirectX 11
2nd Graphics CardNONE
Memory - Hard Disk120GB KINGSTON V300 SSD, SATA 6 Gb (450MB/R, 450MB/W)
2nd Hard Disk1TB WD SCORPIO BLUE WD10JPVT, SATA 3 Gb/s, 8MB CACHE (5400 rpm)
View 9 Replies
Jan 20, 2016
I'm running Windows 10 Pro from SSD and before I installed my storage drive (drive H) it would boot up in less than 15 seconds. With my 2TB Seagate drive installed, it has taken as long as 45 minutes to boot! Every time I start the PC, it says scanning and repairing Drive H. I have scanned the drive with SeaTools and it came up with no problems. I also scanned it from within Windows using sfc /scannow and it also found no issues. Even transferring files to the H drive, is impossible as it just stops transferring altogether and causes the PC to freeze and trying to download Steam games to it, results in a timeout error.
It is not listed in the BIOS as a boot drive so I am absolutely stumped! I have replaced SATA cables and changed the SATA port with no difference.Remove the drive and the PC boots and behaves like it should.
I have replaced the drive twice under warranty thinking that it was a drive issue, but every drive has the same problem. My other 2 HDD's (both 500Gig) have no issue like this at all.
BTW, I have my games folder on the drive, nothing else and it still has about 70% of it's capacity free. It is fine when the drive is empty, but the more data that you put on it, the more it slows the computer down until it gets to the stage where I am at the moment and nothing more can be installed or transferred onto it even though there is tons of storage space available on it.
View 9 Replies
Nov 7, 2015
Internet slows down for one computer but not all of them, I have some troubleshooting information below.
Code:
[CMD]C:UsersJason>ipconfig /allWindows IP Configuration Host Name . . . . . . . . . . . . : JasonMcKay Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : NoEthernet adapter Ethernet: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Qualcomm Atheros AR8152 PCI-E Fast Ethernet Controller (NDIS 6.30) Physical
[Code].....
View 2 Replies
Aug 2, 2015
I just installed win 10 last day, and it was going fine, no conflicts on the drivers whatsoever. But after a day, when I booted up, it seems to have slowed down to a point that everything does not respond to my inputs, though it does after a couple of minutes, i check the task manager and it shows that the disk usage is high, the r/w speed show high utilization about 10-40mbps and the active time is 100%? I have read some thread and suggested to turn off superfetch and prefetch but that didn't do a thing to me. Btw, I installed it over win 8.1 using a bootable usb.
View 5 Replies
Oct 8, 2015
I have a brand new HP laptop with 8gig of ram, and noticed that with cortana location enabled my wifi speeds slow way down especially since the last windows update. Noticed this since the latest windows 10 update which was suppose to update cortana?
View 2 Replies
Aug 4, 2015
I recently upgraded from 8.1 to 10. Performance seems great in general, but Visual Studio 2013 really slows down the system, both when parsing the project directory and during compiling. Chrome for example takes up to a minute to load a single page. I tried setting the process priority to low, with no effect. Under Windows 8.1 I didn't have any problems with VS.
I tested other applications such as the Unreal Editor and rendering a video from Adobe Premiere, both also get the CPU usage to 100%, but don't have any impact on the general system performance, so VS is the only app where I notice this behaviour.
View 8 Replies
Jan 12, 2016
Since upgrading from windows 7 to 10 my pc has been slowed down to a crawl by periods of very high cpu usage. A major culprit, but not the only one, is local security authority process.
This makes the laptop overheat , reduces battery life and slows work to a crawl. I have run sfcscannow and dism as administrator and no fault has been found..
View 4 Replies
Oct 5, 2015
I am using Windows 10, and I am trying to copy one folder to another folder using File Explorer. If I click on a file folder, I find that the "Copy to" and "Move to" icons are both greyed out. The only option that I find available is the moving or copying of individual files. I need to move folders with a lot of files and sub-directories in them.
View 3 Replies
Jul 18, 2015
Is it at all possible to take the OS, already installed, from your PC and put it onto a USB? I plan on getting Windows 10, but want to be able to revert to Windows 7 if I don't like it. (I don't have the computers disks, as it was a hand-me-down birthday present from my older sister.)
View 1 Replies
Mar 16, 2016
What's the difference between using the backup facility on windows 10 to a usb, to simply copying the c: drive to a usb?
View 2 Replies
Aug 10, 2015
I have just upgraded to Win 10 but now when I try to save pictures from my Nokia it says access denied, even the Nokia suite does not sync? I tried to use snipping tool to capture the dialogue box but I can not save that either, tho I have copied it below. I have lowered UAC status, but that does not work?
View 9 Replies
Jul 23, 2015
I am using Win10 10240. I have a problem copying a large number of big files. The setup is a bit tortuous.
The source is an old WD Cloud NAS on ethernet via my ethernet connected router. The destination is an external hard drive on USB3.0
Using file explorer, I drag a bunch of folders to the destination and copying begins but either stalls soon after or indeed never starts. When it works the speed is around 10Mp/s but why does it stall at random places?
I've tried just copying a single folder too. Single files are OK. I've looked at the resource monitor and so on and can't see anything odd although I'm no expert there.
I don't know of any other way to get these files across. The WD Cloud software is hopeless and not fit for purpose in my view. Would a command line xcopy batch file be better? Or third party stuff?
View 5 Replies
Nov 5, 2015
Even though I had only 1.3GB used on a 32GB SD card, I could not copy a 7GB file from my C-drive stating there was not enough free space. Why and what to do.
BTW - the sd card was NOT formated in FAT32 and was formated in the NTFS.
View 3 Replies