I have an ASUS e56u laptop that I updated from Windows 7 to 10. Since the update the -Intel(R) Centrino(R) Wifi N-6150- driver is not starting up. It is the newest version (ver15.12.0.9).
View 2 RepliesI have an Acer Aspire E5-571 and am trying to switch from the graphics driver provided by Acer to the newer version for my graphics card available directly from Intel. The card model is HD Graphics 4400 and the CPU is a 4th gen Core i5 so I'm pretty sure this is the correct driver.
I have tried uninstalling the graphics driver through the Windows Device Manager, then rebooting and installing the driver from Intel, but I continually get the message about my computer having a customized driver from the computer manufacturer. It seems that as soon as I uninstall the driver, it is immediately reinstalled by Windows, thereby not giving me the chance to switch to the Intel driver.Is there a way to manually switch to Intel's driver?
I have a PC with Asus P9X79 Deluxe motherboard. It has Intel chipset and Intel BIOS RAID (RSTe) and 6 SATA ports connected to it. The chipset IDE controller lists in Linux as:
Intel Corporation C600/X79 series chipset SATA RAID Controller (rev 06),
and the PCI ID is:
0104: 8086:2826 (rev 06).
My RAID configuration is 2xOCZ-VERTEX4 256GB SSD's in RAID0, as boot drive (C: drive), and 2 (quite old) WDC WD2500KS 250GB disks in RAID0 for extra storage (games, movies etc) (J: drive).
So yesterday I decided to upgrade my Windows 7 Ultimate to Windows 10 Pro. All seemingly went well during the upgrade process, and the system booted fine, and most stuff seemed to work as it should. But after a while when I accessed files on the J: drive I started experiencing random (temporary) freezes.
Then after a while it got more serious and the whole system froze, I had to hit the reset button.
So I rebooted and looked in the event log, I get see tons of errors there saying that the disk has a bad sector.
Then I try using the J-drive again, by viewing some videos there, and it works fine, but after a while there are some freezes and then I see in the event log, that the drive was reset. After this it works again for a while but then another of those resets comes, and freezes everything for a short while (like 30 seconds).
But when I try to copy some large files off the J-drive, another reset comes, and then the event log starts showing a lot of the error messages from before, with "the disk has an bad sector". (I will post screenshots of these errors after I reboot back into Windows).
After this I can't access the J-drive at all, and Windows gives me error messages when I try to.
So, I figure that I might have just got unlucky and the old WDC drive actually developed read errors, although it's strange that it happens exactly when I install Windows 10 (these drives are something like 7 years old).
Well I can't copy the contents off the disk from Windows since it keeps failing as described above, so I boot into Ubuntu Linux from a USB stick, so I can use ntfsclone to image the J-drive to another disk. I start it running expecting that I'll start seeing read errors, but to my surprise there are NONE. It also copies all files off the J-drive without any problems from inside Linux!
So it was after all not the old drive that had failed, but instead Windows 10/Intel had failed me in a big way.
I trawled the web for updated Intel chipset drivers and installed those from the Asus site, but it made no difference at all. I couldn't find any other Intel drivers and when I searched for the RST drivers on Intel's own site, I could only find ones for Windows XP upto Windows 8.1, but none for Windows 10.
For now I'm left with a PC that I can't use, because I can't go back to Windows 7 and Windows 10 is not working with my RAID arrays. I got some spare 2TB disks, and I'm right now copying all the data from the old J-drive (the RAID1 about 500GB) over to this, hopefully I can then work in Win 10, but I am VERY concerned because the same RAID and drivers are used for my master boot drive with the two OCZ SSD's.
I get this error on a Surface Pro 3 which I have updated to Windows 10. It normally occurs when playing Minecraft, anywhere from 5 minutes to 1 hour after opening. I have attempted to update the drivers, but it says that the drivers are up to date (which is odd as I am using Windows 8 drivers on a Windows 10 machine).
View 1 RepliesNew build. From a fresh install of windows 10 i try to install the drver for my IGPU Intel HD 530. each time i do that i get a BSOD with this message:
VIDEO_TDR_FAILURE igdkmd64.sys
Or sometimes it's
SYSTEM_THREAD_EXEPTION_NOT_HANDELED igdkmd64.sys
I've tried drivers from motherboard manufacturer CD, website and intel and some autodetect driver software. I always get the same behavior:
The screen start blinking several time ( black screen) before showing the BSOD then reboot and repeat it self. Even the driver downloaded by windows update have the same impact.
I've managed to install it in safe mode but when i restart in normal mode i get the same behavior.
I've tried 2 different monitors, VGA and HDMI , tried with UEFI on/off => same result.
I've tweaked once the tdr delay to 8 second, but didn't work.
CPU: Intel I7-6700KMotherboard: ASUS Z170 PRO GAMING
RAM: HyperX FURY HX421C14FBK2/16 - 16Go Kit (2x 8Go) 2133MHz DDR4 Non-ECC CL14 DIMM
SSD: Samsung EVO 850 MZ-75E250B/EU 250 GB
with 80 PLUS 550W power supply.
OS: WINDOWS 10 FRENCH HOME X20-25432
Alright, My specs:
Intel i7-4720HQ processor
nVidia GTX 960M
Intel HD Graphics 4600
Every time I start off a boot, my intel display driver fails to work. Right after logging in on Windows 10, I can clearly see that the animations are laggy and my computer isn't running on the intel HD 4600 driver. When I open up the device manager I get a yellow triangle next to the driver and I have to disable it and re-enable it, for it to work. This happens after every boot and it's annoying. Everything is up-to-date. And I tried system restore, didn't work. BIOS reset, didn't work. It's a laptop so there is no switching ports and what not.
I upgraded both my desktop and laptop to Windows 10 recently. The desktop's upgrade went smoothly; NVIDIA already has Windows 10-compatible drivers. However, my laptop with Intel HD Graphics is a different story. I've tried the Dell-certified drivers as well as the latest ones directly from Intel, and neither work.
When I attempt to install the driver, I get an error message stating "This computer does not meet the minimum requirements for installing the software."
I get the message this computer does not meet minimum requirements. I have gtx 970 with latest driver and I installed latest drivers from mainboard site. My motherboard is asrock z97 fatality killer. My cpu is i5 4460.
View 1 RepliesMacbook pro early 2011 bootcamp was not willing to let the SSD run in AHCI mode in windows 10, so I did EFI installation of windows 10. Everything seems to work but the audio card.
Code: This device cannot start. (Code 10) in the High definition audio controller.
I tried installing the drivers manually and automatically and from the bootcamp but this error persists.
Is the problem in the EFI implementation of the macbook pro early 2011 that windows cannot read , or is it related to drivers ? I downloaded latest videocard Intel HD 3000, and realtek generic driver. The audio drivers seems to be from currus logic.
On Bootcamp install (BIOS) the sound card works fine, but in EFI it can not start the driver.
I very briefly switched on the IGP whilst swapping from Nvidia to AMD last month and now Windows Update is constantly trying to update (and failing) the drivers even though no Intel drivers are currently installed, I used DDU to remove the Intel and Nvidia drivers.
How to stop it? Now whenever I open Windows update I get updates are available for Graphics Adaptor WDDM1.1, 1.2 and 1.3 for Intel HD Graphics 4600
I can't even search for new updates any more!
I very briefly switched on the IGP whilst swapping from Nvidia to AMD last month and now Windows Update is constantly trying to update (and failing) the drivers even though no Intel drivers are currently installed, I used DDU to remove the Intel and Nvidia drivers.
How to stop it? Now whenever I open Windows update I get updates are available for Graphics Adaptor WDDM1.1, 1.2 and 1.3 for Intel HD Graphics 4600
I'm running a 64 bit Windows 10 laptop. On idle, the System process is showing a high memory usage of more than 150 MB, usually more than 200 MB. Using poolmon the pooltag SpDN showed up with a memory leak. It leads to the Intel Matrix Storage Manager driver, iaStorV.sys. How should I go about fixing the problem?
View 1 RepliesI am trying to install intel RST (rapid storage Technology) to try to restore my once blazing fast laptop.
Not that it works anyway but the setup keeps asking for .net framework 4.5
But windows comes with .net framework 4.6 & 4.5 and below.
So I tried disabling the windows one and re downloading it and that didnt work, it says already installed. How do I get around this?
I have a laptop with an intel AC 7265 wireless adapter built in. With the normal Windows 10 driver, AP mode works - which I need to run Connectify.
I upgraded to the latest Intel driver as I was having other issues (Wireless would just disconnect and give me a 1609 address) but the new driver apparently doesn't support AP mode (hosted network support = no).
How I can get AP mode supported again?
I updated W7x64 to W10 Pro x64. The machine is WXP generation notebook. My problem is that the Intel PRO/Wireless 3945ABG is not recognized or Network and Sharing Center - Change Adapter Settings does not list this adapter. The Device Manager does show the adapter but with exclamation mark. What I have done so far are uninstalling/reinstalling the adapter and installing the drivers in compatibility mode.
View 6 RepliesUpgraded Win 7 Pro Dell laptop to Win 10 Pro. Screen resolution changed on first win 10 boot and other resolutions greyed out. Windows update says unable to update Intel HD graphics drivers. Downloaded win 10 drivers from Intel site and installed. On reboot get continual bsod as above. No restore point since upgrade. Can't boot to Windows. how to get past the bsod
View 1 RepliesI'm using Win10 x64 and Intel 520 240GB SSD:
For my mobo, Asus P8Z77-V-Deluxe, I downloaded the official asus chipset drivers.
There is one for Win8.1 x64 and a Beta version for Win10.
The chipset driver for Win8.1 has installed the following:
1. under Device Manager> IDE ATA/ATAPI controller > Inter 7 series/C216 chipset Family SATA AHCI Controller
2. Version 12.8.0.1016 - Date 2013/08/01
If I install the Asus Win10 chipset driver, then instead of the Inel SATA controller, I'll end up having Standard SATA controller by Microsoft.
I'm currently using the Asus beta Win10 chipset driver, however I manually installed the Intel SATA controller which is officially supported on Win8.1 and is digitally signed.
I ran two SSD benchmark test with AS SSD (latest version).
With just the official Win8.1 chipset driver as mentioned above, I'm getting the following results:
With the Win10 beta chipset driver and the Standard SATA controller by Microsoft:
And here are the test results made by Intel SSD 520 Series Solid State Drive | Intel,SSD,520 Series,Solid State Drive,SSDSC2CW240A3,Benchmarks,Performance,Reviews,Olin Coles,Intel SSD 520 Series Solid State Drive SSDSC2CW240A3 Benchmark Performance Review by Olin Coles
Can spot the difference?
After installing build 10074 followed by Windows Update, I got the following report, "ELAN DRIVER UPDATE FOR ELAN INPUT DEVICE FAILED - ERROR CODE 0x80070103"
View 1 RepliesMy friends have problem after she upgrading to windows 10 from windows 8.1. Driver still enable but every time connect using wifi always have limited access and can't connect internet. She is also have try other wifi connection and all have limited access. There is also system batch error before, but now doesn't show again.
View 5 RepliesI have been using this version of windows 10 from last 1 month. I installed all the drivers and everything was working just fine. From last few days my wifi driver isn't responding. I tried reinstalling the driver but the problem still exists.
I can connect through the Ethernet cable and the Bluetooth driver is also working. Only the wifi driver has stopped.
My laptop is Dell inspiron 5520
After I uninstalled catalyst control centre (because I was having problems with it). When I restarted my mouse and keyboard weren't working. So I tried a ps2 kb and mouse and this worked. I went to device manager a looked at the USB devices, all of them had a yellow warning sign next to the devices. I checked each one and they all had error 39 (missing or corrupted drivers). I tried updating and uninstalling the devices with no avail. How can I fix this?
View 1 Repliesupgraded from win 7 to win 10 and love it, but, my usb to serial adapter driver will not start the port, code 10..
View 2 RepliesI just installed Windows 10 and have got a problem that has me stumped. I have two GPUs, an EVGA GTX 760 as my primary and a GTX 560 Ti running a second monitor. The 760 had no issues in the upgrade, but no matter what I do to the 560, it shows up in device manager as Code 43. I'm trying to gauge if it's an issue with the fact I have two dissimilar GPUs or a bit of software not liking that particular card. My gut says software, but I don't know exactly what. I've done some googling to the effect and seems to be I'm not the only one with troubles but didn't find a fix that worked.I don't want to roll back just yet and my 760 can pick up the slack easily, so if there's a fix on the horizon I can wait. Otherwise, I'll have to check my options.
View 1 RepliesNot sure how long this has been the case but Edge won't open for me any more. I'm getting the following in Event Viewer:
Code:
Log Name: ApplicationSource: Application ErrorDate: 09/19/2015 8:57:55 PM
Event ID: 1000Task Category: (100)Level: Error Keywords: Classic User: N/AComputer: Desktop
Description:Faulting application name: Microsoft Edge.exe, version: 11.0.10240.16463, time stamp: 0x55d56349
Faulting module name: eModel.dll, version: 11.0.10240.16463, time stamp: 0x55d55fb5
[Code] ....
Tried running a Powershell fix I found
Get-AppXPackage -AllUsers | Foreach {Add-AppxPackage -DisableDevelopmentMode -Register "$($_.InstallLocation)AppXManifest.xml"}
but it made no difference.
While trying to plug in a VGA cable, I accidentally turned off my power strip, which cut the power to my computer. When I turned it and my computer back on, I was unable to connect to the internet via Ethernet cable.
I went to device manager and under network adapter, it said "This device cannot start, code 10." I've tried reinstalling it, both automatically and manually from a CD and USB. I've done almost everything I can think of to fix this. I scanned and fix any errors on my hard disk, I've reinstalled all my USB drivers, I've power-cycled my router, I've tried different Ethernet cords, and I've tried to delete any corrupted files in my registry, but that must either not be a thing on Windows 10, or I am doing something wrong.
OS: Windows 10
Processor: Intel i7
Motherboard: Asus
I've got the error code 52 in device manager for all 3 imaging devices (an internal and an external web cameras and an HP scanner). I was using Windows 8.1 on my Toshiba Satellite laptop and upgraded to Windows 10 Home edition a few months ago. All the time the imaging devices worked normally and I seemingly some Windows update resulted in to code 52 (Windows cannot verify the digital signature for the drivers required for this device).
Unfortunately returning to previous restore points did not work. I tried to remove the upper limit filter which I found in the registry key HKEY_LOCAL_MACHINESYSTEMControlSet001ControlClass{6bdd1fc6-810f-11d0-bec7-08002be2092f}. As the result the yellow triangles and errors with code 52 disappeared and scanner could work, but both cameras still fail to work. So I restored the registry to the previous state. All the drivers are up to date.