A two-year old PC had no problems with the video driver of that era, when running W7.
Now, under W10 HOME (1511 build) seeing occasional video crash/restore alerts and occasional momentary black screen.
Intel 4000 video has been updated to latest driver. No change. No virus; clean machine. 20Gb C: drive space left.
I just upgraded from Windows 7 to Windows 10 and now my computer only detects one display rather than two. I have a Dell desktop computer and two Dell monitors. Using Windows 7 both monitors were being detected/used. How to correct. The second display shows a black screen with the message "Cannot Display This Video Mode".
View 6 RepliesSo, my old 670 burnt out in a weird way where it would do basic video but only if nvidia drivers werent installed, if they were installed then the system with that card was a brick. Was using a 550 while waiting on shipping, works fine but obviously can't have good settings with it. My new Gigabyte gtx 960 windforce 4GB just arrived, I let it get up to room temperature since it had been outside in the cold for a little bit, then plugged it in. Through HDMI and both DVI ports the only output is a blank screen with a " _ " at the top and nothing else. Looks like a prompt but does nothing. It does not even boot the bios that I can tell. Even if the old 670 had a problem it at least did basic video and showed the bios.
Windows 10 64 Bit
Intel i7 3770 @ 3.4 GHz
Gigabyte g1.sniper m3 BIOS F10f
Gigabyte gtx 960 Windforce 4GB
HP Pavilion 27xi 27"
The monitor is connected to the computer via HDMI and we can see Windows on the screen but Windows sprawls beyond the physical edges of the screen in every direction. That means we see only the top little bit of the task bar and the Windows button is beyondn the left edge of the screen and the clock is beyond the right edge of the screen. I've tried a few different screen resolutions but the image ALWAYS sprawls so that all four edges are lost. What do I need to do so that this sprawling stops?
View 2 RepliesHow to get rid of little black computer screen that pops up very briefly every now and then...
View 1 RepliesI have a notebook from HP dv603290br with Radeon HD 6550D but could not get the video driver to work properly.
View 1 RepliesI got a problem with my GPUs on my laptop.
Basically, after closing a game (WoT), but not all times, I get a BSOD which refers to the folder igdkmd64. I tried any solution, but none of them worked. How can I solve this?
Most people I've seen usually have appalling (almost unreadable) quality when using an external monitor with an HDMI cable -- it's quite simple to fix really easily. Films / video are usually OK but if you are reading email or doing standard computer work then you want the monitor to give you decent results.
First ensure that the "Sharpness" setting on the monitor is set correctly -- oversharpening makes text etc look terrible.
secondly use something like "Auto size" so the picture size fits the screen properly rather than be slightly too large or small even if say 1920 X 1080 HD is selected.
thirdly use correct frequency for scanning -- in Europe should be 60 or 59HZ - use the "p" choice not the "I" one.
finally use sensibly the smart picture settings if you have one or use colour / tint / contrast / brightness settings properly.
Messing around with these controls really does turn an external monitor from in some cases having an almost unreadable screen to a pleasure to use --even on cheap 22 inch TV's.
Use the monitors own menu - don't do it from the PC display settings.
A typical laptop's video card will be perfectly ok on these types of monitors.
I am running Windows 10 with the Insider Program. It's the 64 bit version. I have the latest (just checked) NVIDIA driver for my GTX 560 Ti.
In the last few days I've experienced a problem in which the graphics driver crashes and then recovers after a few seconds. When it crashes, the screen goes black, as if there's no signal. Then it goes back on, but if I was playing a video when it crashed, the media player (MPC-HC) needs to be restarted, otherwise playback cannot be resumed.
It also happens during general use, ie web browsing and such, though it certainly is more frequent when playing back videos. I'd say 80% of the crashes occur during video playback. And when that happens, in addition to the black screen, the GPU's fan goes full power until the driver is restored.
Since NVIDIA hasn't released a new Windows 10 driver since July, is it safe to say that it's a hardware and not a software issue?
Recently i've updated my pc to Windows 10 and now it keeps crashing/hanging quite often and mostly while im in games.
Basically the "shutdown sound" plays, PC freezes, monitor goes black, keyboard and everything else switches off but apparently the pc continues working since i could hear teamspeak in the background once. Nothing else works and the only thing i can do is hard reboot. Unfortunately because of that no minidump is created and nothing is mentioned in windows event journal (except unexpected shutdown). Its almost as if PC switches off videocard and monitor and all peripherals but doesn't reboot.
I've run several hdd tests (crystal disk info, hdd tune pro, acronis disk doctor, western digital hdd tool) and 2 of those (crystal disk and hdd tune pro) showed 1 bad sector in a non system drive while the other two showed healthy/fine disks. My system is on ssd drive which is healthy according to all 4 tests.
I've also tested RAM on memtest86 and it did not found any errors in one full pass though i realise that it might take several passes to show errors. I've also run driver verifier and checked all non system drivers but again did not get any issues.
Additionally i've encountered some other issues after updating to Windows 10 which might or might not be related to the issue above:
1) Videos in media players as well as in flash/youtube sometimes stutter. This never happened before and it seems to be related to higher CPU or disk usage, even though previously videos did not stutter even under load.
2) Some software like lcdhost, logitech gaming software, aida64 behaves strangely - sometimes applications hang, sometimes they do not load, sometimes they unload. I've actually had one BSOD related to AIDA64 which produced minidump but it seems to have been fixed with the beta release.
3)Windows event journal mentions some issues with winnit and service control manager/_session1.
4)Nvidiabackend process keeps taking up to 40% of CPU power occasionally. Before updating to windows 10 i've never had that issue. Killing the process results in "nvidia geforce experience" not loading and then the process restarts anyway.
Im not sure what to do next since i've checked and tested just about anything.
Since upgrading to Windows 10 I've experienced cxonstant screen flickering during gaming. I can only really describe it as a weird fluctuation of brightness, in horizontal lines, up and down my monitor. On Counter Strike it seems to have been somewhat solved through V-Sync but I'm trying to play other games and it is making them completely unplayable.
I have turned V-Sync on through the Nvidia Control Panel and it has done nothing. I've tried running games at various different graphical settings and it has not worked. I have also tried running my monitor and PC from different power sockets just in case the PSU is somehow interfering and it has done nothing.
I have also experimented with running my monitor at different hz but I only have the option to run at 60hz.
Relevant specs are as follows:
Intel i5 CPU @ 3.3ghz (4 CPUs)
8GB ram
Nvidia GeForce GTX 770 graphics card
Dell U2312HM Monitor
I have a gigabyte MB with on-board graphics, 1 vga and 1 DVI as outputs.
I have 2 new asus monitors with 1 vga input and 2 hdmi inputs.
The vga to vga connection to monitor 1 produces full screen on 1920x1080 (recommended)
Asus furnished a cable DVI to HDMI. This connection (monitor 2) leaves about 1/2 inch blank space on either side and about 1/4 inch top and bottom. 1920x1080 (recommended). 1280x1024 setting fills the screen, but display looks stretched.
So the bottom of my monitor display is cut off. It is a Dell ST2010 monitor very old but still in working condition. It has nothing to do with screen resolution btw.
This is how it looks now, the problem started occurring like 3 months ago
This is how its suppose to look when i take a screen shot of it
This has only started happening recently - every few boots, the screen choice between Windows 10 and XP appears with the wrong resolution. The image is small on the screen. If I select Windows 10, the full boot sequence continues with that resolution. However, if I select 'Advanced options' and then 'Continue to Windows 10', the resolution changes to the correct format.
A week or so back, I went back to a previous set point and that seemed to cure the problem. Then it returned.
I have a MSI GS60 ghost pro gaming laptop which has Intel HD graphics 4600 and Nvidia GTX970M GPU, CPU i7 4720HQ, running Windows 10. I study abroad, several months ago i went back home and plugged-in my laptop to the TV via HDMI for gaming like normal. Yesterday i bought an ASUS VC239H external monitor and tried to do the same thing, but there is no HDMI input signal, the Laptop cannot detect the monitor (include display settings, intel HD graphics settings, nvidia settings). This is what i tried:
- Fn+f2, Fn+f8 keys, windows P switching to duplicate or extend or anykind of options
- plug the monitor into my friend's laptop with windows 8 through that HDMI cable and it works fine, the same with other laptop running windows 7==> cable and monitor are normal
- plug my laptop to my neighbor's smart TV. There was ''connected' symbol which appears on the TV but black screen instead of image, Laptop couldn't detect the TV
- reinstalling nvidia and onboard-graphics drivers and update to the latest
- Made a clean install of windows, tried windows 8 also but the same result
- Updated my BIOS and EC
- Bought an adapter HDMI-Mini Displayport to use the mini displayport with HDMI cable
nothing works
There is a feature missing with screen configuration under Windows 10 and new Amd drivers Crimson, even the last WHQL ones (15.12). The Amd setting do not have the screen configuration, no more.
The driver choose ( I guess) the screen number 1 by its connection type Hdmi vs the screen number 2 the vga one (by default the main screen, in Italian "schermo principale")
It's impossible to change that order . And it can be a problem because if the screen 1, a Panasonic plasma through its Hdmi-2 port), is turned off (not the stand-by) the screen 2 do not became the active screen and no login screen is displayed on start. Obviously when screen 1 is turned on the issue ends.
I installed Windows 10 and now get a black screen when I try to watch a video on YouTube. The volume plays, just no picture.
View 1 RepliesUnsure what is happening here, for a few days now, when I load a youtube video, all I get is a black screen, and I do not see the video until I 'nudge' a few keys and throw mouse at screen (not really!)
Whilst this is happening I went up to 200mb last night from 150, so its not my broadband.
The image shows screen after approx 20 secs; the buffering circle only appears after I hit spacebar or enter. Thats does not mean I get the video though, it can appear now, or in another 30 sec or more
So I recently had to reinstall Windows 10 to resolve an issue I was having, so my Nvidia drivers were deleted in that process. When I went to turn my computer back on after i was finished, there was no display on the screen so I took out my GPU and plugged the VGA into the integrated graphics and it worked fine. This just made me think I have to install the Nvidia drivers again but then I found out that you need the GPU in your computer to install the drivers, but My display won't work anymore with the GPU inside and no drivers for it.
View 5 RepliesIn NVIDIA Control Panel, when I select my settings and click apply every things is OK. The next time I reboot they change. Why are they not being saved?
View 5 RepliesI upgrade my Win7 Pro to Win10 Pro last night and lost my 3840x2160x30 setup, being reduced back to 1980x1200. I've since done a clean install and reinstalled the latest drivers for my Samsung U28D590D and My ATI Radeon HD 5770.Nothing i have done has given me back my 4K resolution.
View 5 RepliesI am cleaning out and setting up an old-ish PC and whenever I connect it to my TV or Monitor it says either "No Input to TV" or it is just black when I turn it on, I am using VGA to connect it, I tried with a GTX 650 and with just the built in graphics, and still no luck, any reason why?
View 6 RepliesIn October I bought the MSI GTX 980 graphics card as an upgrade for my Radeon R9 280x. I presumed that I would be getting a lot better performance in games since the 980 is a much more powerful card, this was the case in some games like GTA 5 where I can run the game at much higher settings. However I have found that in a lot of other games my performance seems to have gone down, as an example I will use Borderlands 2 as I have been playing this a lot recently.
Using my old card I was getting pretty much a constant 90+FPS when playing Borderlands 2 but with my current card I am currently getting less than 60 at most times and during combat it can drop to 20's. This doesn't make any sense to me as I have not changed any other hardware other than the graphics card and somehow It is performing worse than my old card.
I understand that the CPU is one of the biggest FPS factors and know that an upgrade to that would be needed for a lot higher FPS but surely an upgrade shouldn't cause an FPS decrease.
My system specs are listed below.
So I read about setting display to Extend I've tried updating the graphics card, looks ok and Device Mgr sez it's working The external display, a TV, worked before on Win 7 just fine!
this is:
Win 10 64 bit Home was Win 7
HP Pavilion dv7 laptop
AMD Radeon HD 6300M Series video card
external display: large TV via HDMI
whenever I try to install the AMD drivers either via running the installer or auto detect, in the end I'm getting a message saying files did not install and to check the log file. I've got an Asus r9 280x. Control panel says "microsoft basic display adapter" under display adapters.
View 1 RepliesI have an Asus Desktop. I plugged a working HDMI cord into my older Sony Bravia TV (Smart TV). I have a GTX 760 192 Bit NVIDIA graphics card. I went to the NVIDIA control panel, and it wont read the TV. I tried going through the windows 10 64 bit version of trying to find connected devices, and the TV shows up but as a media streaming device. It almost seems like the PC itself doesn't know it has an HDMI slot.
View 3 Replies