Hard Drive Partitions - Allocated But Are Labeled As Unused
Mar 14, 2016
I'm just doing some spring cleaning on my laptop and I noticed a couple of partitions on my hard drive. Well, I'm mostly curious about two. Both of them are about half full. Neither one has a drive letter, and one of them has this label: System. They're allocated but are labeled as unused partitions. What do these partitions do and how careful do I have to be with them? I need to move partitions around and such to merge with and extend my C drive.
The Windows Central Universal Application for Windows 10 Mobile on a Nokia Lumia 830
I have been trying out virtual box and running Linux distros. The computer started malfunctioning after updating a Linux distro running in virtual box needing to do a factory reset to my computer but all good now.
I plan to dual my computer with Linux and Windows 10 but when checking in Disk Management I noticed I have 6 partitions on the hard drive.
My question is could I delete the 490mb 45 mb 7.92gb partitions ready before I install a Linux distro.
What partitions I should have on my hard drive after I upgrade from Windows 7 to Windows Home Premium Build 10586. I have some new small partitions and I don't know if they belong to the OS or they got allocated from another source.
Still learning Win 10 ways! I have installed a WD My Book backup drive, and Win 10 gave it the designation of my "G" drive. How do I change from "G" to a different unused letter?
Basically I have two drives in my computer that both had windows 10 installed at one point, I removed windows off of one of them and I'd like to remove the drive from my PC entirely, but whenever I take it out windows gives me a message "install valid boot media and restart". What do I need to do so I can remove said drive and keep windows?
(also after that I'm going to install an SSD and copy over windows from the drive I'm not removing if that makes any difference)
I want to upgrade to Windows 10, and unfortunatly, the only way for me to do so is by doing a fresh installations and deleting everything, wich I don't want to. I want to back-up my current data on a hard drive partition, if I do a fresh installation of Windows 10, will it delete my partition alongside my data inside it?
I have windows 10 build 1511 on a USB stick made by windows media creation tool now when install windows the drive has zero partitions.
When i install the copy from the USB stick i end up with 3 partitions one is 450MB (recovery partition) and another partition at 100MB called (EFI System partition) and last partition is windows 10.
Now if i delete all the partitions and install windows 10 from the USB drive again i get two partitions one at 500MB called (System Reserved) and the windows 10 partition.
Why if i install windows 10 multiple times i get different partitions being made?
I would like it to only make the two partitions every time.
So I recently bought a ssd to add to my pc so that I could add my OS and some other files on to the ssd and keep my old hdd as storage. After finally getting the OS onto the ssd and being able to boot from it I tried to transfer all of the files back to the original hdd from the backup I had made from the ssd after cloning the drive. Once completed the hdd was no longer showing up at all in my computer so I went into disk management and tried to set a path for it, but it was now split into two partitions (I am assuming because I took the backed up ssd and put it onto a hdd because the size of one of the partitions is the size of the ssd). I tried formatting both partitions and then extending it to combine them but whenever I do this it tells me there is not enough space on the disk to complete the operation.
While inslating Win10 i my new computer i made two partitions on the SSD, but this is giving me some problems of space, so i want to merge the C: disk with the F: disk (the D: disk is a hdd), in the C: disk i have the IOS and some other apps and the F: is empty. How to do this?
I have attached an image of my Disk Management screen. Disk 0 doesn't look right to me. Is there a problem here? if there is, how do I correct this? I am running W10 and the C drive is a Samsung SSD drive.
I have a Dell Venue 8 Pro with an upgraded Windows 10 installed. Always perform Windows Update but did not pay attention too closely. When the drive space was low and started looking a little bit closer, I found out that I have several Recovery Partitions. From Disk Management display, from left to right are the partitions:
The problem is I do not know which partition that Windows 10 actually created as its Recovery Partition. I do know that the 4.75 GB partition is my original Dell Venue 8 Pro Recovery Partition. Which one can I remove to allow the expansion of my C drive? What gives?
I recently used a 16GB USB flash drive to create an installer for a new Linux distro. I noticed that the created partition is 8GB and the rest 8GB is unused. I want to create a second NTFS partition so I can use the USB as a recording medium for my PVR, but Disk Management doesn't give me this option. I then used MiniTool Partition Wizard Home Edition, which did create the partition but warned that it won't be recognized by Windows as it normally sees only the first partition on a USB Flash drive. I even went back to Disk Management and assigned a drive letter to the second partition, but in Explorer I see only the EFI partition (first, drive is formatted in GPT mode) with that drive letter. Is there any workaround? Of course I could just format the whole drive as NTFS, but I wouldn't like to do so until I don't need the installer anymore.
Problem: When I click on my H: drive or try to access it from the command line, it gives me an access denied error. However, all of the applications that I have installed on that drive run without issue. So, there is some access there. (See attached images. The first shows the hard drive state in diskmanager and in windows explorer. The second image shows the minecrafter launcher profile (that it is stored in H: and the application running, proving that there is some access.
System: Home built PC: (C:) 240GB SSD for OS, (E:) 1TB HDD for file storage and backup, (H:) 1TB HDD for large applications and video editing files. All drives are Simple, Basic, and none have encryption. All use the SATA connectors.
Process: I had Windows 7 Home 64 bit with, among many other things, Comodo Internet Security, Virtualbox, ImageDisk. During the upgrade process, I noticed that Windows 10, during the upgrade, ran the file system check and fix "problems" on the H: drive.
(Side note) Having forgotten to uninstall Comodo before the upgrade, I did not have network after the upgrade. The fix was non-trivial as I had to use a second computer to download the unofficial comodo uninstaller. Reboot. Uninstall the network devices. Reboot. And once Windows 10 was up and running, it reinstalled the network devices and the network was available.
Still, whether before or after the Comodo uninstall and reinstall, the uninstall of ImageDisk, or the uninstall of the Virtualbox network device, I have no access to the H: drive.
Pen Drive and external hard drive keep getting errors! So I select to fix the problem scandrive recommended scan and repair. But there's never anything wrong with them it reports! And it takes ages to scan it takes 10-15 minutes for 32GB pen drive. Windows 7 Pro done it in a flash! Anything I can do about it.
I clean installed Win 10 RTM version on my laptop a few weeks ago. I have a basic GPT setup.
Installation went fine, however the installer created a 'Recovery' drive (D with a size of 600 MB (262 MB free) & a 'Local Disk' drive (E with a size of 451 MB (128 MB free).
I am stumped as to why it assigned letters to them. If you see the attachment of a snapshot of Partition Wizard, you will be able to see the setup.
My question, besides why the assigned letters is the where the status is listed as 'None'. Is it safe to delete these?? I am assuming that the only partitions i need to keep are the 'ESP', which is 'Active & Boot' - so it is needed to be able to boot into Windows. How about the one listed as 'Other' - the capacity is 128 MB & all 128 MB are used - do i save this one as well?
I really wanted a less cluttered setup - so when all these partitions were created, particularly 'D' & 'E', i was perplexed as to why they were created.
Ever since doing a fresh install of Windows 10, in "This PC", my secondary hard drive is not in the list. I have already tried right clicking "This PC" and clicking Manage -> Disk Management, but there is nothing there except my SSD with Windows 10 installed.
I have tried changing SATA cables, SATA ports, but it still does not appear in This PC. I have also tried installing my hard drive on a another computer to see if the files were corrupted. They were not, all files were still the same before the installation of Windows 10. I did not leave the hard drive plugged in during the installation.
In the BIOS, my computer recognizes both my SSD and my hard drive, but in This PC, it's still missing.
I have a SSD where my operating system is installed.I also have a 3 3TB drives. A 746.52 partition on one of the drives became unallocated after installation of windows 10. I've managed to recover all the data from the unallocated partition. Would now like to fix the partition. I think it may be something to do with MBR/GPT?
So, I've had this 1Tb HDD lying around unused, so I had the bright idea of shoving it in place of my Dell Latitude E6410's original 640Gb HDD, use that in place of the old 60Gb HDD on my T60 (a mere 60Gbs just weren't enough to accommodate my Google Drive - running on Linux with InSync - and Mega cloud storage), and put my latest W10 Pro system image on the 1Tb in the E6410.
All well and good so far - except when I checked the partitions after I reinstalled the system image from the original 640Gb, this is what I got:
Which wasn't too surprising, given how Windows works. What I wanted to do was to expand C: into all that extra unallocated space, but as you can see, the recovery partition is in the way. I wouldn't be too surprised, either, if there was no workaround that doesn't involve reinstalling Windows.
I have had windows 10 since the beta and I recently bought a kingston 120gb ssd I want to do this by reinstalling but since I got windows 10 during the beta with no install disk I have no ability to simply reinstall but how to transfer my license.
I have two hard drive on my PC, as SSD for the OS and a HDD for all my storage.I seem to have a problem with search, that it will only find stuff that is stored on the SDD.To get it to look for other files on the HD, I have to click search my stuff, and even then it still doesn't work.Is there a way to fix this? As most of my stuff is on HD and click search my stuff is a bit annoying.Also when I click rebuild index, nothing happens. I get a dialogue box saying it will take a long time, but then it doest say its indexing
My old computer was a windows 8 that was upgraded to windows 10. I just ordered a new i5 6600 which comes with windows 10, a 250G SSD and 1 TB hard drive.. My old hard drive appears to be a Seagate Barracuda 1TB SATA which seems to be the same as the one in my new Vanquish. My old hard drive is 2/3 full and is backed up often. My question is can I move this old hard drive to my new computer as a separate drive without formatting it and use the data on it (or transfer my data) or does it need to be formatted (thus giving me roughly 2 TB of space with the 1 TB provided with the computer). It was my C: drive in the old computer.
I have an HP G42-154CA that I'm trying to get Windows 10 Pro installed on.
[URL]
I ran into an issue with the installation disc not detecting the hard drive (ie, no hard drive is listed when the screen appears to select the hard drive to install Windows on).
I've tried various drivers (latest from HP and Intel website, OEM OS installation discs etc) with no luck.. at the very least, the Windows 7 driver from HP's website for that laptop should work for installing Windows 7- same results, does not detect hard drive.
At this point I'm wondering if maybe it's a BIOS setting that's causing this? I don't recall changing anything in the BIOS when I last installed Windows (which was v8), but it was awhile ago, so can't be certain.
Haven't had to rip lately, thought it was easy, went to play a cd in the player and I can't rip cds in Windows 10 to hard drive. What am I missing? WMP will not allow ripping.
