I have two drives with files on them and want to make one drive A inactive(remove windows) so that I can make the other drive have windows 10. What is the easiest way to do that without removing or formating Drive A.
View 2 RepliesI have Windows 7 and Windows 10 Enterprise Build 10240 set up in a dual boot configuration on the same hard drive. Windows 7 is the first partition on that drive and Windows 10 is the second. I have decided to keep Windows 10 as my main OS and want to remove Windows 7 and reclaim that space for the Windows 10 partition.
What is the easiest way to accomplish this without a complicated and long procedure? I have tried Easeus Partition Master 10.5, but am unable to format or delete this active partition. I tried to format and/or delete this through Windows 10 as well with no success.
I am dual booting Windows 10 and Windows 8.1. Each operating system is on a separate physical solid state drive. My default is Windows 10. The Windows 10 OS was installed on the drive that originally contained Windows 7 when I dual booted Windows 7 and Windows 8.1. I don't have drive partitions to deal with as each operating system is on a separate physical drive.
Now I would like to remove the dual boot by removing Windows 8.1, leaving just Windows 10. That will leave me with an unused SDD.
When I am in Windows 10, the default OS, the msconfig Boot section shows Windows 10 as the default, as it should. To remove the dual boot, can I just Delete Windows 8.1 from the Boot section of msconfig and make the setting permanent?
I have a old windows 7 safe mode boot screen that migrated over to windows 10. I works on windows 10 but I don't need it any more so I want to get rid of it. I just don't want to mess up in removing it... I'm using this tutorial... Can't get rid of the dual-boot option on start-up ?
View 6 RepliesI have uninstalled KB3035583 which has removed the windows 10 script from my taskbar, however I am still getting a message that there is an important update when I boot up to the initial Windows 8.1 screen before my login. On checking what important updates are available, it is only the Windows 10, KB3035583 that it is obviously trying to get me to update again.
After 2 weeks of failure on updating to Windows 10, I have decided to stay with 8.1. I now want to remove the advice to install importantant updates, that pertain to Windows 10, but still showing those for my Windows 8.1 system. At this point, when getting this message, I don't know if it is still just for Windows 10, or if new updates are available for my 8.1?
I want my ssd to be the boot drive and hard drive for storage. I recently installed windows and I accidentally installed it on the hard drive.
View 1 RepliesWhenever I try to install a 64 bit Windows 10 copy from a flash drive, I get stuck on the 4 blue squares, with no white dots spinning. Then after about 10 seconds the PC restarts. I have tried the official way with the media creation tool, I have tried just downloading the ISO and using a third party bootable USB maker, I have tried ISO's from pirate sites (yes, I know, not the best solution) but none of those worked. Every time I tried a different method I always fully formatted the USB drive. Oddly enough the 32 bit version worked once or twice but even that doesn't work anymore. My PC specs are quite good so I really don't know what's the issue. Btw im running a 120 GB AData SSD and a 1 TB Seagate hard drive.
View 5 RepliesBasically I have two drives in my computer that both had windows 10 installed at one point, I removed windows off of one of them and I'd like to remove the drive from my PC entirely, but whenever I take it out windows gives me a message "install valid boot media and restart". What do I need to do so I can remove said drive and keep windows?
(also after that I'm going to install an SSD and copy over windows from the drive I'm not removing if that makes any difference)
How do I automatically mirror files from a hard disk drive to a network folder?
In this case I want to mirror the contents of an entire disk containing photos (no system files) to a shared folder on an OpenMediaVault server running on my home network.
This is separate from the regular backup of the rest of my system which is done with backup software. For the contents of this disk, I don't want them compressed into a backup container file. I want them to be exact duplicates of the original files, kept up to date in that shared network location (login required).
Also, it doesn't matter if they update in real time. Once a day is fine, for example.
I have Windows 10 on a 2TB HDD with about 1TB of the HDD full. I would like to migrate Windows to an 80GB SSD but I can't find anyway to do this without cloning the entire drive, which I can't do because there is too much content on the HDD. Is there any way to migrate Windows to a different drive whilst keeping all user files and installed applications on the old drive so I can have two drives in my system, the SSD for boot and the HDD for storage and applications.
View 4 RepliesIn my desktop I have two hard disks ( disk 0 and disk 1 ) . Disk 1 is a clone of disk 0 created by Macrium Reflect
Disk 0 : ( C: ) windows 10 pro , upgrade from windows 7 , ( E: ) windows 8.1 pro , ( G: ) Storage partition
Disk 1 : clone of disk 0
problem description : I see in msconfig / boot a wrong listing
windows 10 ( C:WINDOWS) : Current OS ; Default OS
windows 8.1 pro ( H:WINDOWS ) instead of ( E:WINDOWS )
Nevertheless the dual booting works fine as well as the shift between the disks via BIOS.
The question is , could I fix the situation using the EasyBCD of Neosmart Technologies to edit the bootloader ?
I see can change drive letter H: to E: and save the change , am I right or wrong ? or any other way ....
When I try to boot from a recovery flash drive, it fails with: EFIMicrosoftBootBCD error status: 0xc000000f and message: The Boot Configuration Data for your PC is missing or contains errors.
The recovery flash drive was created on a Lenovo ideapad originally with Windows 8, now upgraded to Windows 10, latest upgrades applied. Checked the box for copying system files. Target drive was a 16GB DataTraveler flash drive formatted as FAT32. Creation ran to completion with no errors. When booting normally, Windows 10 runs fine with no issues. I tried re-creating the recovery drive with the same results.
I created a repair disk and tried to use bootrec to fix the issue, but I suspect it did nothing or fixed the c: drive. I ran boot rec while in the root directory on the flash drive.
I was moving video files (AVI) from an external backup drive (WD Element) to another external backup drive (Seagate expansion) after having moved another video file from my laptop (Acer) to that Seagate external drive. The night before I had moved some video files from the WD to the Seagate with no problem but using a different laptop (Sony). These video files are all rather large and I can tell that the space is still being allocated on the Seagate because while the folder cannot be seen the space that was there is still being used by the Seagate because I am missing over 100GB which would be about the size of that now missing folder.
What happened was there was a message that the Seagate drive could not be recognized while the files were in the process of being moved to that drive from the WD. This is after I had already moved a video file of about 26GB with no problem into that now missing folder. When I saw the message I attempted several times to move files to that Seagate drive but I could not so I unplugged the Seagate drive from that laptop (Acer) then reinserted it into the usb port. I got a repair message that said it needed to be repaired because some files were corrupted and that no data would be lost but the drive would be unavailable during the repairs so I checked ok. It took only about 30 seconds and it said the repairs were completed and the drive was available but I noticed that the folder that I was moving the video files to was not gone.
As I stated there are more than 100GB of files in that folder some are video and others are audio recordings that were created by using the myrecording (audio and video) features of the Acer laptop and they are very important so I need to figure out if they can be retrieved from that Seagate drive. I have not copied anything else onto that Seagate drive but I have plugged it into the Acer computer to ensure it is being recognized. Both the external drives WD and Seagate are plug and play that are powered from the usb -- they have no power adapters.
I have a legacy 64 bit dual core desktop (ASUS mobo). I have several Sata hard drives in it with the 4th partition of my 1 Terabyte drive containing my Windows 10 Professional boot OS. After converting another similar legacy machine to a NAS device I took the old Windows 10 32 bit OS drive from it and tried booting the ASUS machine with it. Needless to say, the OS didn't like it and reverted to Windows 10 Pro Insider Preview edition (build 11082).
When I tried to restore the boot drive to the original one for this machine the master boot was missing.
I had just formatted another partition on the same drive that had contained a Windows7 installation that had failed. This partition may have contained the master boot record. So I booted to a command prompt from a USB drive and successfully ran the following commands:
bootrec /RebuildBcdbootrec /fixMbr bootrec /fixboot bootsect /nt60 SYSbootsect /nt60 all
After that the BIOS just says "An operating system wasn't found. Try disconnecting any drives that don't contain an operating system" This disk and OS are on the original machine it used to run on. As I understand it, Windows 10 tries to record it's key to somewhere in the BIOS. But the BIOS on these old machines don't provide such a facility. I don't understand what Windows 10 OS does with the key in this instance. If it was recorded in the BIOS then I'd presume that the other Windows 10 drive I attempted to use would have found it and used it. Or perhaps not, since it didn't like the new environment.
what I'm looking for is a way to get my original Windows 10 to boot again on the same machine it had always work on before, from the 4th partition of the 1 terabyte drive I'm using.
Have HP Pavilion Dv5 running windows 10, I purchased a new HP Envy with Win 10 installed.I want to give DV5 to my step-daughter with Win 10 on it, and remove me from laptop and Win 10 completely. I have files stored on flash drives and OneDrive and have a Microsoft Account.
If I do a total reboot of Win 10 and have her as Administrator and get a Microsoft account, that should work? My Microsoft Account and OneDrive will be able to link with new Envy laptop and with installed Win 10?
I'm pretty sure I'll be upgrading my desktop this week while I'm on vacation. I've done my laptop with no problems at all, it's a Dell Latitude E6400 with Win7 Pro bought refurbished from Newegg. The laptop was a mid 2008 model and W10 works great on it.
My question is about my desktop drives, my OS drive is an SSD and my backup drive is an HDD. There is nothing but the backups and system image on the HDD, it is an inside the box drive connected to the second SATA on the MB. Is there a chance the W10 upgrade will put it's boot loader/manager on the backup drive?
I have seen posts where for best results, all drives except the one being upgraded/clean installed on should be disconnected to avoid the boot loader/manager showing up on another drive. I can do this but it's sort of a PIA due to pulling the tower out, disconnecting cables, and opening it up. Then repeating after the upgrade to put things back.
My backup drive is an HDD with nothing on it other than backups which are done every Sunday night. There is no OS on the backup HDD.
Background is, I created another partition on my 120G SSD (30G) where I've been dual booting 7 and the W10 TP's, the plan is to delete that partition and recover the space for the W10 upgrade. Then have a single partition with W10 on my 120G SSD C drive and to continue to use the WD 500G for backup and system image. I will create another partition on the backup HDD for the W10 backups (right now I'm using a 100G partition on the HDD for Win7) and keep the Win7 backup and image until I'm fully on and comfortable with W10.
My pc was installed with windows 10 dual boot with windows 7. After I removed windows 7 from harddisk somehow the dual boot options were not removed. I am still able to log into windows 10 but it is kind of disturbing. How should I completely remove the dual boot screen and log into win10 directly?
View 1 RepliesI have Dell Inpiron 3420 Laptop. Windows7 Home Basic was my built-in OS. Now i have upgraded it to Windows10 Home Edition. Now i have left less space in my C-drive. So i want to delete unused files, folders from C-drive. And I also want to backup my windows10 too.
View 9 RepliesI have signed up for nothing, nor agreed to anything (knowingly) but I am concerned that Win 7 updates are 'prepping' me for the win 10 upgrade. Rather than MS having my interests in mind, I've been forced to scrutinize every update that is offered so I have turned Automatic Updates off. I caught the KB 2952664 update and have hidden it, but I am wondering if there are other such "updates" out there that will force/nag me to "upgrade"?
View 3 Repliesi was create map network drive in windows 10 now i need remove but idont now how removed it
View 4 RepliesI wasn't sure which forum to put this into. I created a backup image on a usb hard drive. I wanted to be able to restore it using a usb recovery thumb drive. I used the create usb recovery tool and created the recovery flash drive. When I try to boot from the flash drive I get an error saying that the boot configuration data is missing or contains errors. I can boot up the laptop using the current windows install so it isn't referring to the hard drive. I have tried several usb drives and get the same message on each. Here is a screenshot of the message.
View 9 RepliesMy laptop doesn't boot because OS is on E: drive instead of C: drive
When I try to boot it up (it somehow boots up as windows 8.1 instead of my OS windows 10), it gives a BSoD and shows the error code 0xc000021a. I created a bootable USB drive with windows 10 pro on it, but it shows my OS as windows 8.1 instead of 10, and it doesn't allow me to restore or do a startup repair, because they both fail.
Booting up:
Repair shows windows 8.1 instead of 10:
I have only win10 installed, and one system drive. By accident I boot from win8 dvd, and now win8 appears in boot menu. I tried to remove it in msconfig, deleted and rebooted, but it reappears.
Also I tried to add safemode options to boot menu, I followed tutorial and used command prompt and bcdedit, safemode option appears in boot menu but it doesnt work, it only reset my machine and boot to win10, it doesn't go to safemode. This is how bootmenu look, but only win10 works.
How to remove all other items except win10, for good?
msconfig dont work as they reappear.
How to add safemode item, so it can really work?
How to remove those annoying "back up files" notifications in action center when I already use an external drive
View 1 RepliesMy Windows 10 seems to share some files and i cannot figure out how to disable files sharing.
I have 0 files in my Media player library, also, i have no other dlna sw installed that shares anything.
How to remove these files from shared list?
I just realized that all the shared files are .mov files. Are the .mov files automatically shared somehow?
From the start screen, type 'inetcpl.cpl' and then press Enter. In the Internet Properties window, click the Security tab, click the Internet Zone (globe icon), and then click the Custom level button. In the Security settings window, scroll down to Downloads>File download. Click to select Enable. Scroll down the list further to Miscellaneous>Launching applications and unsafe files. Click to select Prompt (recommend). Click OK. These steps will remove that default security block for downloads.
View -1 Replies