My pc was installed with windows 10 dual boot with windows 7. After I removed windows 7 from harddisk somehow the dual boot options were not removed. I am still able to log into windows 10 but it is kind of disturbing. How should I completely remove the dual boot screen and log into win10 directly?
View 1 Replies
I have Windows 7 and Windows 10 Enterprise Build 10240 set up in a dual boot configuration on the same hard drive. Windows 7 is the first partition on that drive and Windows 10 is the second. I have decided to keep Windows 10 as my main OS and want to remove Windows 7 and reclaim that space for the Windows 10 partition.
What is the easiest way to accomplish this without a complicated and long procedure? I have tried Easeus Partition Master 10.5, but am unable to format or delete this active partition. I tried to format and/or delete this through Windows 10 as well with no success.
I am dual booting Windows 10 and Windows 8.1. Each operating system is on a separate physical solid state drive. My default is Windows 10. The Windows 10 OS was installed on the drive that originally contained Windows 7 when I dual booted Windows 7 and Windows 8.1. I don't have drive partitions to deal with as each operating system is on a separate physical drive.
Now I would like to remove the dual boot by removing Windows 8.1, leaving just Windows 10. That will leave me with an unused SDD.
When I am in Windows 10, the default OS, the msconfig Boot section shows Windows 10 as the default, as it should. To remove the dual boot, can I just Delete Windows 8.1 from the Boot section of msconfig and make the setting permanent?
My Grandma pokes around way too much in her computer that has Windows 10 I used to remove all kinds of things in Windows 7 but since upgrading to windows 10 I all the things I had setup to no longer show are now back again after update. The things I would like removed are...
The power menu when you click Start (I use a CLI command in the Run Box to restart and shutdown)
The Network Icon in the task tray
The Volume Icon in the task tray
Any visible access to control panel (I use Windows+R to bring up run and enter "control")
My network connection user name shows "Secured". Right below is the same name followed by "- guest" and "Open". Is this a potential problem? Does this allow someone else access to my network connection? If so, how do I delete it?
View 2 RepliesIn my desktop I have two hard disks ( disk 0 and disk 1 ) . Disk 1 is a clone of disk 0 created by Macrium Reflect
Disk 0 : ( C: ) windows 10 pro , upgrade from windows 7 , ( E: ) windows 8.1 pro , ( G: ) Storage partition
Disk 1 : clone of disk 0
problem description : I see in msconfig / boot a wrong listing
windows 10 ( C:WINDOWS) : Current OS ; Default OS
windows 8.1 pro ( H:WINDOWS ) instead of ( E:WINDOWS )
Nevertheless the dual booting works fine as well as the shift between the disks via BIOS.
The question is , could I fix the situation using the EasyBCD of Neosmart Technologies to edit the bootloader ?
I see can change drive letter H: to E: and save the change , am I right or wrong ? or any other way ....
My laptop has dual boot - Windows 7 and Windows 10. My Win7 environment is my main working environment with lots of programs installed and important files. I installed the Win10 environment just to play around with 10 during the technical preview. Now, I would like to disable the 10 environment and upgrade the 7 to 10. Am I able to do this, or have I already "used up" my one upgrade on this computer's Windows license?
I notice that in Windows 7 I have not received the icon in the notification area that invites me to upgrade to 10. This makes me think I might have used up my chance to upgrade.
My end goal is to have a single Windows 10 environment. Note that the reason I want to upgrade my 7 environment to 10 is because I don't want to have to re-install all of my programs and files into the current 10 environment.
After several weeks of testing I'm ready to go full on Windows 10 and want to get rid of Windows 7 but I have some partitioning issues I want to clean up. I currently have Windows 7 on drive 0 (360 GB) and Windows 10 on drive 1 (500 GB). Both are SATA drives and RAID is enabled in the bios but not active.
What I think I'd like to do is simply swap the drives physically so that Drive 0 has my current Windows 10 install on it and make it primary boot active etc. The drive with Windows 7 on it would become drive 1 and I would delete the Windows 7 partition and re-partition it with a clean empty partition just for extra space.
Second question, any advantage to using this drive configuration in a RAID setup?
Today I installed Windows 10 on my machine (ASUS N55SF laptop) for the first time on a separate hard drive. Now I have Windows 7 on my main hard drive and Windows 10 on my new drive (the latter being an SSD one). After installing Windows 10, I got a new boot option in my BIOS called "Windows Boot Manager" which is set as default, but it runs Windows 10 directly, I can't see any boot manager (I can assure "Windows Boot Manager" behaves this way because my BIOS lets me override the boot option, so that I can directly run any boot option, and this is probably the only way I can run Windows 7 currently).
If I go to Start → Advanced system settings → Startup and Recovery → Settings, I only see Windows 10 in the "Default operating system" drop-down menu, while I only see Windows 7 if I do this while on Windows 7. It's like the two OSs are not completely aware of each other.
I cannot get to the advanced boot options menu that I could with windows 7 by hitting the f8 key. You know the menu that has safe mode with Command prompt safe mode with network support startup repair and Just regular safe mode. Use some of those features but I can't get to them the f8 does not work anymore.
View 1 RepliesI am trying to have my computer boot Linux by default, from an external hard drive, while my internal drive has Windows 10 on it. Unfortunately I cannot get it to work: Windows 10 boots automatically at every restart and cold start.
Steps I've taken so far:
The boot order I want is set and saved in BIOS. There's no uEFI on my computer.
Windows 10 fast startup option is disabled. I also disabled the hibernation option just in case.
Still, I can only get Linux to boot by going into BIOS every time and selecting the (already selected) external hard drive again. When I then try to mount the internal (Win 10) disk from within Linux, I get an error saying it cannot be mounted because Windows 10 is still using it.
how to solve this and give full boot control back to BIOS?
I would like to know how to dual boot my win 10 pc with osx as my secondary os. I need mac as I need to see important messages that I receive when I use my pc.
View 1 RepliesEvery time I try to boot into safe mode or advanced options I get the same BSOD ERROR: CRITICAL_PROCESS_DIED.. Is there any other way for me to accomplish this?
View 1 RepliesBasically when i go to turn on the PC it turns on and gets stuck on the screen where it tells me to push DEL or f2 to go to the bios settings. The problem with that is it wont let me access the settings at all when i push either of those buttons. So then I turn my PC off and then on again and it boots fine. Then I check for updates to see if it's some bug and I'm up to date. So I restart to see if the problem has been fixed. And it gives me the same frozen screen of the BIOS options. Then i turn it off and it boots fine, wash and repeat.
Build:
CPU- i5 4790k
GPU- MSI GTX 970
MOBO- Asus Z97
RAM- Corsair Vengeance 2X8 GB
PSU- Corsair 650 watt
Memory- Samsung SSD 120GB, Western Digital Black 2 TB
I have win10 64 installed on my SSD and win10 32 bit on a HD. The SSD is GPT partitioned and the HD MBR. I can boot from the Windows boot loader in the BIOS into 64 bit windows on the SSD and, by selecting the appropriate HD in the BIOS into the 32 bit windows in the HD. I cannot figure out how to get that boot menu (either gui of text based) that I have read about in the forums. Do I need to convert the HD to GPT as well. Do I need to change anything to get this to work?
View 9 RepliesI have Windows 10 and 8.1 dual booted but I’m having trouble removing 8.1. 10 is on a Seagate 2TB HDD, and 10 is on a Samsung 2TB HDD. Both are SATA and my motherboard is BIOS. As long as the Samsung (8.1) is drive 0 and is boot’s first choice, all is well. I get the option to select either OS, and either one can be made default.
In attempting to remove 8.1 I have tried several things like making the Seagate drive O, removing power from the Samsung, swapping boot choice, but always fail and I continually get, “an operating system wasn’t found” no matter the disk or boot sequence, except the one above.
Included are jpg’s of disk management while in Windows 10, both disk and volume views. How to decouple 8.1?
I attempted to set up a dual boot configuration using my existing Win 7 Pro on a Samsung SSD drive, and a clean install of Win 10 Pro on a fresh Kingston SSD drive. I created bootable Windows 10 installation USB, reset the UEFI Bios boot order and proceeded with the install. Win 10 installed, however it would not recognize the Win 7 Pro drive. I checked the UEFI Bios again, and the Samsung SSD was no longer shown in the "Fixed Boot Order Priorities". However, it was listed under "Hard Drive BBS Priorities", and under "Boot Override". It also shows up in Win 7 in the drives listings.
My motherboard is a MSI Z97 Gaming 5, with Click Bios 4 v1.9.
I must also mention, my Samsung SSD with Win 7 Pro was set up not with UEFI but Legacy boot. This was my first mobo with UEFI, so I made that mistake due to my ignorance.
I reformatted the Kingston Win 10 drive. Rebooted, but got error message that boot device not found. I rebooted and hit F11 to get back into Bios. A popup box gave me a listing of bootable devices and the Samsung SSD appeared. Selected it and it booted into Win 7 no problem. I went back into the Bios, but the Samsung SSD still not listed. I shut down the system, unplugged the Kingston SSD, rebooted, went back into Bios, and the Samsung returned.
I then shut down the system, connected the Kingston into a different SATA port, rebooted the system, went back to Bios, and the Kingston remains unlisted in the "Fixed Boot Order Priorities" as before, but shows up in "Hard Drive BBS Priorities", and under "Boot Override". It also shows up in Win 7 in the drives listings. Remember that the Kingston is just formatted, no op system installed on it.
I set up the Win 10 install on the Kingston SSD as a legacy drive too. Another question I will ask is can you have one operating system on a legacy drive and one on a UEFI drive in the same PC?
My dual boot configuration has 10 with classic shell and 7 pro. Classic shell has settings for taskbar which control opacity and color. My 7 just showed a nearly transparent taskbar so I went to 10 and changed classic shell taskbar settings to opaque then back to 7 and the taskbar was now opaque.
View 3 RepliesSo i currently have windows 10, build 10162, and i like the OS X, especially since i do video editing, and i love the workflow. The problem is, everything on my PC is optimized for windows, and some things wouldnt work on a mac, and i didnt want to spend the money on a mac. I know its possible to dualboot some OS's so i want to know if theres a way i can just add an OS to my current pc. I have an extra HDD that i could put it on. And i want to put Yosemite on it, and i also have an intel CPU, nvidia card, which i believe is necessary for a hackintosh.
View 1 RepliesI'm planning to download the iso, or whatever file it is from the Microsoft website, and install it using that. (I never got the taskbar notification,.how I can make a dual boot on my second hard drive using that download (another thread I made, I've gotten the hard drive working and want that to be my dual boot, not having two operating systems on one hard drive)
I would like Windows 10 on my second, completely wiped hard drive.Unless I'm able to use my Windows 7 disk to install it on the second hard drive, and use the Windows 10 download to upgrade it on that hard drive in particular?
I just installed windows 10 on my second ssd and I have win 7 on a different.
How do I get a screen at bootup so I can pick what os to start?
Now I have to go to bios and change boot order of drivers every time I want to boot into a different os. I get no boot screen where i can just select what to start.
On the bottom of windows 7 there is a icon to upgrade to windows 10. However, is there/will there be a way to upgrade to windows 10 and keep windows 7 in a dual boot configuration.
View 1 RepliesI've installed Win10 on secondary HDD and I kept my WIndows 7 on different HDD.How do I setup dual boot?Each time PC reboots its loading only windows 10 without any dual boot.I can change the boot order in my BIOS but it would be great if I can do it via dual boot
View 1 RepliesI'm using WIn 8.1 as my main OS, but I have the 10 Home preview (Build 10240) on a second hard drive and I'm dual-booting. But there's something strange happening:
- If i set WIndows 10 as the default OS, then the PC boots to the OS selection screen and gives me 30 seconds to pick which one I want to use
- But if I set 8.1 as the default, it boots directly into 8.1 and doesn't let me select the 10 preview.
I'd prefer to have 8.1 as the default, but I don't want to go into BIOS every time I want to switch between them.
So, currently, we're trying to dual-boot Windows 10 Technical Preview on a Toshiba laptop with Windows 8.1. We already got the partitioning set up and everything, but when trying to install, it says we can't install to a GBT partition, or something along the lines of that.
We went to try to install it the same way that you do for Windows 7 and everything else, but upon setting the disk drive to the boot device, it still loaded into Windows 8. After a little Google work, I found that Secure Boot must be turned off, and that the BIOS option has to be changed from UEFI to CSM. After doing that, we could boot into the Windows 10 disk. However, when trying to install it, it says "Windows cannot be installed on this disk. The selected disk is of the GPT partition style"
We would like to fix it, and I found a way to do so on a Microsoft forum, and that's as follows:
1. Boot up to installation DVD/CD.
2. Click install but don't follow through.
3. Press SHIFT-F10 to bring up console.
4. Type "diskpart"
5. Once inside diskpart type:
-> list disk (find the one you want to convert)
-> select disk 0 (select the one you want from the list)
-> convert mbr (should take a second or two)
-> quit
6. Continue with install
But I need to know if it will format the entire hard drive, as I'd prefer not to lose the data on the primary partition. If we can do it while only formatting the partition for Windows 10, that would be fine (as that's empty already anyway).
New Dell XPS8700. Upgraded from Win 8.1 to Windows 10 and worked fine for about a month.
On start-up, it now hangs on the Dell logo or when trying boot options to start from USB or recovery DVD go to blank black screen. Dell phone support sucked but they sent me a recovery USB drive (to factory set Win 8.1), however start-up would still hang at the Dell logo. Tried all different boot combinations from CD/DVD, USB, OS/Boot partition but cannot proceed beyond Dell logo or black/blank screen. I do not have a original Windows 10 OS disc, however did a download from
HTML Code: [URL] .... to USB and PC does not boot up from that media either.
Used an original Windows 7 Ultimate installation CD to start and get to command prompt to recover files from C: drive and can browse through all folders and files. Copied user data to USB drive. So HDD appears OK.
