With Vista/7/8/8.1, having more than 1 HDD/SSD physically attached meant that the system partition(s) could potentially be on any disk. Is this still the case in 10, or has Microsoft finally fixed this bug?
View 3 Replies
My nice new SDD arrived, I installed it into the PC and disconnected the other SATA drives bar the DVD, spun up my W10 DVD and fairly quickly had a new activated install of W10.
So I plugged in the old SDD (it has the old C: on it) and the HDDs and it booted off the old SDD.
Unplugged the old SDD, plugged in the new one plus the HDDs, it wouldn't boot.
Went back to just the new SDD installed, boots fine, hot-plugged the HDDs and it wouldn't see them.
So right now I'm back where I was with the old SDD and the two HDDs which are mirrored.
Prior to doing my Windows 10 upgrade on my HP Pavillion DVT7 2200 Notebook, I successfully created the 3 Recovery disks. Prior to that I was receiving messages that a hard drive failure is eminent and I should back up my files and replace the hard drive. My Windows 10 upgrade went fine and for most part I'm happy with it. My issue now is my XP Mode is not supported and I have lost a VM that is use run legacy software.
My question is when I run my system recovery is it going to roll me back to where I was before creating the Recovery disks? Will I have to reinstall all my software? I have ordered a replace HDD from HP and it will be arriving on Wednesday.
Is there any way to remove eject from my internal drives. Windows 10
View 9 RepliesI am referring to this tool.
View 4 Replies I'm pretty sure I'll be upgrading my desktop this week while I'm on vacation. I've done my laptop with no problems at all, it's a Dell Latitude E6400 with Win7 Pro bought refurbished from Newegg. The laptop was a mid 2008 model and W10 works great on it.
My question is about my desktop drives, my OS drive is an SSD and my backup drive is an HDD. There is nothing but the backups and system image on the HDD, it is an inside the box drive connected to the second SATA on the MB. Is there a chance the W10 upgrade will put it's boot loader/manager on the backup drive?
I have seen posts where for best results, all drives except the one being upgraded/clean installed on should be disconnected to avoid the boot loader/manager showing up on another drive. I can do this but it's sort of a PIA due to pulling the tower out, disconnecting cables, and opening it up. Then repeating after the upgrade to put things back.
My backup drive is an HDD with nothing on it other than backups which are done every Sunday night. There is no OS on the backup HDD.
Background is, I created another partition on my 120G SSD (30G) where I've been dual booting 7 and the W10 TP's, the plan is to delete that partition and recover the space for the W10 upgrade. Then have a single partition with W10 on my 120G SSD C drive and to continue to use the WD 500G for backup and system image. I will create another partition on the backup HDD for the W10 backups (right now I'm using a 100G partition on the HDD for Win7) and keep the Win7 backup and image until I'm fully on and comfortable with W10.
Will it remove all of my games i installed on the other drive such as D: if i upgrade from 8.1 to 10 ?
View 2 RepliesI have only win10 installed, and one system drive. By accident I boot from win8 dvd, and now win8 appears in boot menu. I tried to remove it in msconfig, deleted and rebooted, but it reappears.
Also I tried to add safemode options to boot menu, I followed tutorial and used command prompt and bcdedit, safemode option appears in boot menu but it doesnt work, it only reset my machine and boot to win10, it doesn't go to safemode. This is how bootmenu look, but only win10 works.
How to remove all other items except win10, for good?
msconfig dont work as they reappear.
How to add safemode item, so it can really work?
I upgraded to Win 10 from Win 7 yesterday. I now have a translucent rectangle on the upper left corner of my screen. It's a lighter shade than the background color of the desktop. Can't move or remove it & don't know what caused it but it is distracting as it also appears on screen when running an app. How did you fix?
View 1 RepliesI am dual booting Windows 10 and Windows 8.1. Each operating system is on a separate physical solid state drive. My default is Windows 10. The Windows 10 OS was installed on the drive that originally contained Windows 7 when I dual booted Windows 7 and Windows 8.1. I don't have drive partitions to deal with as each operating system is on a separate physical drive.
Now I would like to remove the dual boot by removing Windows 8.1, leaving just Windows 10. That will leave me with an unused SDD.
When I am in Windows 10, the default OS, the msconfig Boot section shows Windows 10 as the default, as it should. To remove the dual boot, can I just Delete Windows 8.1 from the Boot section of msconfig and make the setting permanent?
I have the following entries in my system start up:
Windows 10
Windows 10
Windows 7
How do I remove the last two entries so startup just shows one Windows 10 only or just boots right into Windows 10 without a start screen ?
In ADMIN TOOLS|COMPUTER MGMT|DISK MGMT the following are listed...
C: 952 GB
"healthy recovery partition" 450 MB (the box is shaded)
"healthy recovery partition" 449 MB
D: 909 GB
How can I get rid of the recovery partitions (or at least one, if the other is required) and reclaim the unused space for C: ?
After win10's installation my external monitor has black borders.
This was happening also with win7 after installation. with catalyst control center [which I cannot open anymore in win 10... as I have an ATI Mobility Radeon HD4670 which is not supported] I could easily fix the issue:
- open Catalyst Control Center
- go to My Digital Flat-Panels
- choose Scaling Options
- slide the slider all the way to the right (so that it is a 0%)
So, this is a monitor scaling options (or border padding I think in windows) issue that I need to fix. I search everywhere but I cannot find any fix in win10.
I am using Windows 7 SP1 [ Genuine ]. My upgrade to windows 10 is ready via windows update but i don't want to install it. how to remove this option so that normal system updates can be install.
View 2 RepliesWhat I mean is, if I select to keep my personal files only, will the installed programs be removed completely from my hard drive, or will they be moved to the Windows.Old folder like what happens in Windows 7 or Windows 8/8.1 ?
Because I would like to have them in the Windows.Old folder in case I might need some of the files there, but I want the installation to be clean as well.
I've tried downloading and installing Windows 10 via the System Update for the past 24 hours (I've tried it 5 separate times). Every time it gets to 84% overall, and 36% configuring settings, then goes to a black screen with nothing on it (including no cursor) and almost no HDD activity. This has happened all five times.
Windows 7 Ultimate 64bit SP1
Intel Core i7-2600 CPU
16gb Ram
AMD Radeon R9 380 Series
Single monitor
last few hours I spent trying to manually deploy Windows 10 on clean GPT disk but after applying image and rebooting I always end in unbootable state.
I manually setup drive like this:
Code:
select disk 0cleanconvert gptcreate partition primary size 350 #RE tools won't fit 300MB anymore :-)format quick fs ntfs label "Windows RE tools"assign letter tset id de94bba4-06d1-4d40-a16a-bfd50179d6acgpt attributes 0x8000000000000001create partition efi size 100format quick fs fat32 label Systemassign letter screate partition msr size 128create partition primary format quick fs ntfs label Windowsassign letter wlist volumeexit#no recovery image partition as per documentation it is no longer needed and followed by pretty common deployment:
Code:
dism /apply-image /imagefile:g:Sourcesinstall.wim /index:1 /applydir:w:dism /image:w: /set-Timezone:"Central Europe Standard Time"md T:RecoveryWindowsREattrib w:WindowsSystem32RecoveryWinre.wim -h -s -rcopy w:WindowsSystem32RecoveryWinre.wim T:RecoveryWindowsREwinre.wimbcdboot w:windows /s s: /f UEFIw:WindowsSystem32
eagentc /setreimage /path T:RecoveryWindowsRE /target w:Windows
After reboot I always end unbootable (as we talk Apple computer it means 1) no partition on Option or 2) folder with ? or 3) just gray screen, make your pick). There's a chance that Windows rely on some UEFI 2.0 feature, which is not available as the old guy has 1.2 only. Or maybe I missed some step somewhere.
Upgrading from windows 7 to 10, started install at around 10:30am and left it....around 2:30pm it started the large circle with the % in the centre, and again left it for another hour or so and came back to a black screen, no cursor or anything.
I waited until about 7:30 and still nothing and did a reboot by holding the power button down. On restarting, I get the windows 10 logo with the spinning dots, and then it cuts to black with no cursor. The CPU light does what it would usually do on startup, and when it first cuts to black but then the screen seems to change to a different black (if that makes sense?!) and the light only blips extremely quickly with a long period before it blips again
i know this is another update gone wrong post but I can't seem to find any with the same problem, just similar ones. I've read it can take a long time, but it's been nearly 11 hours and is very frustrating!
i'm not mega pc savvy, I get 2 options when I boot, and I've looked and there's no option for me to do a safe boot, or to revert back go windows 7. If I leave it on black screen for too long it automatically goes into sleep mode.
Is it advisable to set the UEFI BIOS (Asus ROG Hero Maximus VI motherboard) to a factory default settings before installing Windows 10? Or should I at least set the memory "XMP" profile?
View 3 RepliesFor those people who CLEAN installed Win 10 using the Media Creation Tool, will it automatically update to Threshold-2 (version 1511 Build 10586.36) through Windows Update once installation had been completed? Or does that have to downloaded separately?
And what is the "KB" Number for version 1511 Threshold-2?
i'm having an issue with my laptop, i think it's something called a memory leak because my RAM won't go below 80% even when my laptop is idle. I've been searching the internet for answers on how to fix this problem but didn't find any luck. I've already wasted an entire day trying to figure out how to fix this, I even tried to do a system restore but i forgot to save any restore points. I'm hoping Resetting/Refreshing would be the answer but i'm facing another problem; My media installation tool or USB Bootable Drive (I don't know if they're the same. It's what i used when i installed Windows 10) is that of a previous Windows 10 version & build. Would it work If i use it to Reset my laptop? I'm currently using the latest version, build 10586.36.
View 1 RepliesI recently made a clean install of Windows 10. However when I reboot I noticed that the Wi-Fi tray icon wasn't showing any menu. I click it and nothing happened. No list was shown, the only way to connect was to go to This PC Configuration --- Internet & Networks --- Wi-Fi.
Wi-Fi tray icon, battery and volume don't work. I don't know what to do. I search about it and found something about resetting explorer.exe, I try that but didn't work.
I have 2 seperated (physically) SSD drives in my laptop.Previously I had windows 8.1 on one drive, and I installed windows 7 and upgraded it to windows 10 on the other SSD drive.I enjoyed windows 10, so I formatted the drive with the windows 8.1, but now suddenly my laptop says he can't find system drive, and I can't load the windows 10, althogh it was installed with no connection to the windows 8.1 and on another drive.
View 5 RepliesI have been trying for hours to install windows 10 home on my newly built PC but i can't because there is a problem. I bought the usb version since i don't have an optical drive bay.
The problem: I can start the setup, but when i launch the installation my pc suddenly restarts and boots the usb again, so i get back at the 32/64 bit selection screen. This happens when i click "next" after choosing my drive (see included video). The drive i'm using is a Samsung 850 EVO SSD.
I have tried numerous things to fix it including: removing the ram (2x8GB) and putting it back, trying with one ram stick, removing the graphics card and use the integrated graphics card, use different usb ports, use different sata ports, removing the hdd (i can't even start the setup with the hdd plugged in).
I also downloaded Windows 10 from the official website and put it on an other usb stick, the same problem occurs.
I even tried with Ubuntu and the same problem happens!! When i launch the installation my pc reboots and the setup restarts!
I have made a video showing what happens (win 10): OS installation problem - YouTube
I also made a video that shows my BIOS: Gigabyte GA-Z170X-Gaming 3 BIOS - YouTube
The download of w10 got completed and the installation after 95% restarts and says restoring your previous version. now it is again downloading the 2700 MB.
View 1 RepliesI currently plan on doing a clean install on a new ssd of Windows 10. My current mobo is a ASUS P8z68-V which has UEFI so I plan on doing a UEFI installation of Windows 10. However, I plan on getting a new processor and motherboard sometime in the future, so would I have to do a reinstall of Windows 10 when I get my new motherboard, or could I expect it to boot up normally as would a traditional BIOS system would work?
View 4 Replies
