Installation :: Restore With Disk Image?
Aug 19, 2015How do I reinstall Windows 10 from a USB Disk Image
View 2 Replies
Similar Messages:
Ηow To Restore Capacity Of Hard Disk After Image Recovery
Aug 5, 2015I have 3 HDD's (2 internals (1 SSD 120 GB and 1 HDD-Sata 200 GB) and 1 external USB HDD (2 TB)). I have installed Windows 10 Pro x64 final οn the SSD 120 GB without problems and i have installed the extra programs that i use, also without problems. Then i decided to make an image backup to the external USB HDD. The image created succesfully. After that, i have removed the SSD 120 GB, installed the HDD-Sata 200 GB and tried to check to the HDD-Sata 200 GB if the Windows image recovery works. I used the Windows installation DVD and the external USB HDD to do the recovery.
The image recovered normally and the HDD works like as if i was using the SSD 120 GB. So my problem now is with the capacity of the HDD-Sata 200 GB which is shown as 120 GB. So any way to restore the capacity of that HDD again back to 200 GB? I don't want to format the disk now, just continue to use it as a backup disk just in case of failure of my SSD one. I know that i cannot use the HDD Capacity Restore Tool, because it is working only with 32-bit systems (which i currently don't have one right now) and even if i use it i don't know if it will restore my disk to full capacity but in a state that requires format from the begin (something that i am trying to avoid).
So in general, my question is how to restore the capacity of a hard disk after image recovery (when you backup to a new hard disk with capacity bigger than the capacity of the disk that i want to backup).
Installation :: Image Restore On Larger SSD
Jan 28, 2016Is it possible to restore a Windows 10 system image taken from a 60Gb SSD to a new 240gb SSD on the same computer?
I am thinking of using the windows 10 installation USB to boot then repair to recover the image onto the 240Gb SSD.
Would this work? Does partition size affect the new 240Gb SSD?
The system is already licenced for Windows 10 and nothing has changed other than the SSD volume size..
The VERY last resort is to install over again with all programs, tweaks, etc..but, I'd rather not.
Installation :: Inability To Restore From Image Backup?
Jan 18, 2016I have an unallocated 1Mb partition as the first partition (according to Easus) on my laptop drive, in addition to the recommended reserved, system and EFI partitions. Could this extraneous partition be the reason for my inability to restore from an image backup? (Restores fail after making my laptop unbootable)...
View 9 RepliesInstallation :: Macrium Image Restore Changes Partition Layout
Feb 10, 2016I tried one again to use Macrium to backup only C:, clean install then restore only C:.
Once again it did more that I asked it to and removed the 16MB partition created by the clean install.
After clean install I had this, 4 partitions on Disk 0 (SSD):
After restore I had this, 3 partitions o n Disk 0 (SSD):
I did not run the Macrium fix boot option after the restore so when I rebooted Win 10 ran Auto repair then the system booted up normally.
Why is Macrium doing this?
Guess I'll ask in the Macrium forum and see what I can find out.
The reason I'm doing this is is Shift Restart from Power is not working, it just boots normally.
I just redid the steps in Brink's tutorial to setup Recimage, then ran reagentc /setosimage /path "locationResetRecoveryImage" /index 1
I'll try Shift restart again now and see what happens.
Installation :: How To Create Factory Image Disk
Feb 10, 2016First of all, I upgraded to windows 10 from windows 7. My device is a ASUS K55vd notebook. When I was running on windows 7 I successfully created a factory image disk via ASUS ai recovery application (a five bootable disk). Then I decided to upgrade my hdd to ssd. My idea is to have a clean factory installation of windows 7 on ssd so I didn't clone my old hdd.
What I did was mount the ssd and ran my recovery disk and successfully installed a fresh windows 7, it is then when I update my windows 7 and went to windows 10. Currently I'm running on windows 10 and there is the notification of creating a factory disk which I would like to do but as soon as I start burning the disk it says that the recovery partition does not exist even though I have my recovery drive ( R: ).
Next, I tried creating system repair disc from Control Panel>System and security>Backup and restore (windows 7) then this prompt came. "The selected disc cannot be used. The selected disc does not contain a valid Windows installation."
Lastly I tried creating system image also from Control Panel too. However it failed and says that the mounted backup volume is inaccessible.
In my reagentc /info:
In my disk management:
I would like to ask for some solution regarding that and I'm wondering if the previous factory image disc that I have from before (win 7) is still usable if I decided to factory reset my pc? And can I make a bootable disc in which it reverts my windows to the point where I freshly upgraded to windows 10 so that I would relieve myself the hassle of upgrading again to windows 10 when the factory image disc work (in which it will surely reverts my windows to win 7).
Installation :: Transfer System Disk Image To SSD
Feb 10, 2016I have created a disk image of the system disk, C: with the disk image software in Win 10 backup. The system disk was 70GB with 40GB of files. When I tried to write the image to the SSD the Win 10 install software said the disk (120GB= 110GB) was too small. I reinstalled the windows disk booted and shrank the system disk to just under 60 GB and retried the process with the same result. System is Win 10 32 bit on an old Acer netbook.I would like to be able to transfer the installed files to the SSD.I have looked at the tutorials for creating a system image and also how to create hardware independent image for installing win 10
View 9 RepliesInstallation :: Does The ISO Disk Create The W7 Recovery Image
Sep 13, 2015I created ISO disks for both my 32 bit and 64 bit systems at the MS download site. If I use the ISO disk instead of the Windows Update method, does the install still create the W7 image in case I want to go back to W7 after installing W10?
Also, do I boot from the disk or do I go into the ISO disk and click on Setup?
Installation :: Backup Image To New Bigger Hard Disk?
Oct 9, 2015Is it permitted to install the backup image of Windows 10 to a New bigger hard disk in the same PC. After that I will use the new hard disk only and format the old one.
View 5 RepliesSuddenly Cannot Restore Image By Running System Image
Sep 21, 2015Windows 10 Home.
I created system image backup file at least once a week. I did one yesterday, and today I needed to run it to restore my system. To my horror, I cannot find way to run it. I ran system image backup restore multiple times. I know how to do it...... until today. Today, by the time I clicked Troubleshoot option, there is no Advanced Options to choose from. Instead it sent me to Startup Settings option where I could go to safe mode etc,
I ended up running a system restore. Good thing I do create restore point religiously. But, after system restore, I still have the same problem.......... cannot restore image by using system image backup.
adding............... I went to my other laptop running Win 10 Pro, I had no trouble running system image restore.
Performance :: Can't Restore From System Image
Aug 20, 2015I created a system image on a Seagate external hard drive using Windows 10 Home, and I created a restore disc for booting with an external BUFFALO DVD drive connected to a USB port. I went into the UEFI and set my BUFFALO drive as the first drive to be used for booting at power up or reset. When I restarted the computer, a message appeared saying "Press any key to boot from CD or DVD". I pressed a key. After a few minutes, the following screen appeared:
I used the down-arrow key to select US and hit enter. Then the following screen appeared:
I used the down-arrow key to select "Choose Device" and hit enter. Then the following screen appeared:
This screen gave me only two options: (1) Boot with the BUFFALO optical drive, and (2) Boot with the Solid State Drive which the HP Spectre x360 has (instead of a real hard drive). When I used the down arrow to select the BUFFALO optical drive, the screen that asks for the desired keyboard layout reappeared. When I selected US and hit enter, the screen that asks for a booting option reappeared. When I selected "Choose Device" and hit enter, the screen that gave me the option to boot with either my BUFFALO optical drive or the Solid State Drive reappeared. I found I could keep going around in circles like this, without ever having an opportunity to restore the computer with a system image I had created earlier.
Restore Win7 Image On New Partition
Jul 31, 2015I completed upgrade from Win 7 to Win 10. So far everything seems to be working great. I have a Macrium image of my C drive with Win 7 on an external HD. Can I create a new partition on my C drive and restore my Win 7 image there? That way I can dual boot to either OS. I have done some research and it appears to be a relatively easy thing to do, even for a computer dummy like myself.
View 8 RepliesPerformance :: Restore From Windows Image Backup?
Oct 29, 2015I Created an image backup using Windows 10. I burned the repair CD. I booted from cd. Options are most recent backup [but it only shows D:, the factory backup partition]. No browse capability. Other option does not let me browse to the folder the system created, "F:WindowsImageBackup". How do I restore from this image instead of the factory image?
View 8 RepliesCan't Enter BIOS Menu After System Image Restore
Mar 5, 2016I have an Asus UEFI mobo on my custom-built desktop, a few months old.
B150M-K D3
It has American Megatrends firmware
Today I restored my system from a macrium reflect system image. I went back only 2-3 hours in time. After rebooting, windows started up fine. But the bios reverted to its default settings, although I had previously tweaked it a bit.
What's more, I can't get to the bios menu at all. I mash the delete key at startup, and I just see a blank screen. Even an hour later, just a blank screen.
This happened to me not so long ago, but that time, the bios screen did eventually appear, and with a little patience I was able to tweak the bios again. But this time it is more stubborn.
I also feel that the boot process is slow. I see the asus advert, and it coughs a couple times and drags on until I get to the windows boot menu where I choose if I want windows 10 or macrium reflect recovery environment.
I very often restore from a system image, and every time, it makes a new bios boot entry. I have dozens of boot entries by now in the bios boot menu. Maybe that's causing a problem?
The fan is unusually loud, although cpu usage is low, just 0-2 %
Performance :: 0x80070057 Error At The End Of System Image Restore
Sep 19, 2015A couple of days ago I made a system image backup (there were no error messages that it was unsuccessful), now I need to restore it, I boot Windows 10 DVD, point to a network location and start the restore, but after an hour or so, at the end it errors with "0x80070057: Parameter is incorrect". After that Windows boots to diagnostic mode but fails to repair anything. Diskpart shows that the partition which used to be C is RAW, I also have an impression that the order of partitions is different (C was 3rd, after restore it seems to be 1st).
I checked and I'm able to mount VHDX with C partition and access all files, chkdsk doesn't find any errors on it.
It's a UEFI computer with GPT installation. Is there some way to restore it with some 3rd party tool, or manually? What can I do?
PS: there's a lot of clues on the internet about fixing similar problem when such error popups at the beginning of restore from a USB thumb drive. The solution is to unplug the thumb before starting so the restore doesn't get confused with the additional drive. It's not the case here, I'm not using USB thumb and I get the error at the end of restore.
Update: I managed to restore an older backup of Windows 8.1 from before upgrade to Windows 10. I used Windows 8.1 DVD for the restore.
The difference between an old image and the new one is that after upgrade to Windows 10 I removed an optical drive and replaced it with a SSD which I was using for page file and ReadyBoost. Also, Windows 8.1 had 3 partitions, while after upgrade to Windows 10 I noticed that there's some additional 4th partition (so there were 2 restore or EFI partitions, not sure which), but the backup image of Windows 10 still consists of 3 VHDX files. The image of Windows 10 isn't an image made from a scratch - when I was setting up the backup I simply pointed to the old 8.1 image and Windows 10 was making its images on top of the old one (I wanted it to backup the differences only, to avoid huge transfer of the whole drive).
Anyway, as I already stated I'm sure that VHDX of Windows 10 isn't corrupted. It's probably some problem with XML metadata so the restore procedure can't recreate proper partition layout corresponding with images, or something. A
Image Backing Up Page Labelled As Backup And Restore
Aug 13, 2015Do i have to remove windows 7 from my computer before i can system image W10 ?
View 1 RepliesPerformance :: Restore Points And System Image Are On Backup Drive
Jan 22, 2016Question; My computer had to be reformatted because of a lock out by a hacker, can I use a restore point that I made before the hack, to restore my files? The restore points and system image are on my back up drive , I restored a couple of files from it. and the folders are there but I do not want to screw things up, as I don't know what I am doing.
View 9 RepliesInstallation :: Apple MBP / UEFI Installation Won't Boot After Image Apply
Aug 25, 2015last few hours I spent trying to manually deploy Windows 10 on clean GPT disk but after applying image and rebooting I always end in unbootable state.
I manually setup drive like this:
Code:
select disk 0cleanconvert gptcreate partition primary size 350 #RE tools won't fit 300MB anymore :-)format quick fs ntfs label "Windows RE tools"assign letter tset id de94bba4-06d1-4d40-a16a-bfd50179d6acgpt attributes 0x8000000000000001create partition efi size 100format quick fs fat32 label Systemassign letter screate partition msr size 128create partition primary format quick fs ntfs label Windowsassign letter wlist volumeexit#no recovery image partition as per documentation it is no longer needed and followed by pretty common deployment:
Code:
dism /apply-image /imagefile:g:Sourcesinstall.wim /index:1 /applydir:w:dism /image:w: /set-Timezone:"Central Europe Standard Time"md T:RecoveryWindowsREattrib w:WindowsSystem32RecoveryWinre.wim -h -s -rcopy w:WindowsSystem32RecoveryWinre.wim T:RecoveryWindowsREwinre.wimbcdboot w:windows /s s: /f UEFIw:WindowsSystem32
eagentc /setreimage /path T:RecoveryWindowsRE /target w:Windows
After reboot I always end unbootable (as we talk Apple computer it means 1) no partition on Option or 2) folder with ? or 3) just gray screen, make your pick). There's a chance that Windows rely on some UEFI 2.0 feature, which is not available as the old guy has 1.2 only. Or maybe I missed some step somewhere.
Installation :: Use Image To Upgrade
Oct 18, 2015I have several machine running Windows 7 Professional that I want to upgrade to Windows 10. Question is can I upgrade 1 machine add my other programs Office etc , take an image and then use that image to upgrade the other machines. Adding a new machine using Win7 image was easy, install the image changes the license number for Win7 & Office reboot and that was it.
View 5 RepliesInstallation :: Image From Media Tool?
Aug 27, 2015i decided to reinstall everything starting with windows 7 then upgrading or using the free upgrade that i initialy used to get windows 10. but it seems that offer is no longer on the start menu bar task bar.
i have the img of windows 10 pro burned from media creation tool to a dvd.
can i use the dvd to simply just upgrade windows 7 to windows 10?
or do i need a serial key for windows 10?
i had some trouble with curse client and some audio stuttering in windows 10 when i used the free upgrade, but it didn't show until after i installed call of duty black ops III where it said i needed audio below 44000khz (sound blaster Z) to be able to open the game....... : and a bunch of bsod out of nowhere. i havent had a bsod on windows 7 for over a year so idk where that came from.
is there a upgrade function from the dvd (windows 10 pro; as in the free upgrade) or do i need a serial specifically for win 10?
Installation :: System Image Of Current OS
Jul 25, 2015I am planning on installing Windows 10, and I'am thinking of doing a clean install. So my question is if I create a system image of my current OS i.e. Win 8.1 will I be able to restore it on Windows 10? Because I do not want to install every software again.
View 2 RepliesInstallation :: HDD Has Bad Sectors - Can Put Saved Image On New SSD?
Aug 12, 2015Second device just got win10 logo in taskbar yesterday, but now windows says my hdd has bad sectors and I cannot access it properly. I have a saved Macrium image I made several days ago. Can I put it onto a new SSD and will my existing valid keys still work so that I can get the upgrade?
View 7 RepliesInstallation :: Downloaded ISO Image And Tried To Burn It To DVD Only
Jul 31, 2015I've downloaded the ISO image and tried to burn it to DVD only to find that is too large 5.6 GIG and doesn't fit on a 4.7 : is there a way to get it to fit or can I extract it to desktop and run it from there?
View 9 RepliesInstallation :: Image Corruption - Even After Reinstall From ISO
Apr 14, 2016I have upgraded directly from a Windows Ten Pro ISO downloaded directly from Microsoft, but both sfc /scannow and Dism "restore heallth" run from an elevated prompt report that they cannot repair the image errors. Windows support simply says to "reset" from Update and Security from the Settings menu, but this machine was running CLEAN Windows 8.1 (sfc /scannow or DISM commands reported no errors) and resetting as they suggest will (at a minimum) mean that all of my installed software will be entirely lost.
I am desperate for a person proficient in restoring the integrity of a Windows Ten Pro image (have tried BOTH reinstalling directly from the downloaded ISO (multiple times and from re-downloaded ISO's and doing in-place upgrades). Both methods report the same errors upon reinstallation or in-place upgrade methods.
The running image is corrupt, corrupt, corrupt. What are the command(s) to restore it to health, as was the case with the previous clean 8.1 that was running before the upgrade???
Both Sfc /scannow and DISM restorehealth report that the image is repairable, but it is beyond my understanding how to do do.
Installation :: How To Install Vhdx Image Onto Computer
Nov 29, 2015I no longer have access to the old computer.
From my internet reading it would appear that virtualization might be invovled and I've managed to install a virtual machine on the new computer, however, I've now hit a brick wall ..
The vhdx image file is on an external HD together with bu's of my data files (just to be on the safe side)
Installation :: Creating USB Pen For Dism Apply-image
Oct 1, 2015I have managed to create a USB pen drive to apply WIM images using the DISM Apply-image command in 64bit so I know it can be done but how to create a pen to apply 32bit WIM images
View 6 Replies