Installation :: Sysprep Disconnects NIC

Sep 24, 2015

We have upgraded our MDT 2013 to Update 1 build 8298.And we have quite a few issues that we didn't have before.We have some pretty simple task sequences we use to build images, one for each OS. CurrentlyWindows 7x64, Windows 8.1x64 and Windows 10x64. Each os has a separate virtual machine in our VMware environment. We don't capture the image in MDT since our deployment system requires and older WinPE to run (Capasystems.com).I pick the Syspreb task so it does what needs to be done at the end of the build. Shutdown the machine when it's done, pxe boot into capa and then proceed to capture the image.

After the upgrade I boot from the litetouch ISO like we normally do and using a VMxnet3 driver make the connection to the share and this runs smoothly all the way to the sysprep part. When the machine is done syspreping it completely "drops all network connections" and the build "fails".

Tried with different drivers, old and new. Even tried running it on hyper-v but it yields the same results. Every task sequence was built from scratch since the format part was changed.

View 1 Replies


Similar Messages:


Installation :: Error After Booting VM After Sysprep

Sep 22, 2015

So we're trying to get our first Win10 VM up and running. I downloaded the latest ISo from the Volume License site and installed it on a VM just fine. I ran all Windows Updates as well.

After that I ran Sysprep and choose OOBE, Generalize, and Shutdown. I then copied the VHDX file to a new location for a new VM as we normally do.

That all seemed to work fine until I then attached that hard drive file to a new VM and fired it up. After clicking the through the timezone page I get an error stating:

Windows could not complete the installation. To install Windows on this computer, restart the installation.

I found some info online about changing the minimum password setting to 0 but that did not work. I then fired up my Template machine to see if that would setup fine and that now gets the same error so I'm kind of stuck.

I don't want to have to do manual steps on every VM we create

View 2 Replies

Installation :: Sysprep Error During Upgrade

Jul 30, 2015

Using the media creation tool (both usb and ISO) I get an error. Something like "installation has encountered an error during first_boot with sysprep." In not at my toshiba laptop at the moment so the wording may be a little off. Upgrading from my 8.1 current os. I just read about removing my eset antivirus before upgrading so I will remove that and my malwarebytes program as well and try again.

View 2 Replies

Installation :: Modern Apps After Sysprep Does Not Work

Sep 10, 2015

I install Windows to vhdx in hyper-v. I make two users, make some updates and install some apps. I make sysprep and copy vhdx to another PC and boot from this.

After this, start menu does not work. i can not tun no modern apps, and Notifications panel does not works too. When I make new user, all works fine. I need to make this work for the already created User.

View 3 Replies

Installation :: Unable To Sysprep After Redstone Update

Nov 16, 2015

Recently updated a workbench PC and updated it with the Redstone patch. I attempted to sysprep the PC however I am getting the following Error:

'Sysprep will not run on an upgraded OS. You can only run sysprep on a custom (Clean) install versions of Windows.'

View 4 Replies

Installation :: Driver Auto Load Fail With Sysprep?

Jan 21, 2016

I am working on creating a new master image to deploy windows 10 64 to a new of different models throughout our organization. Currently I am having difficulties getting the drivers to be "auto Detected"

The Sysprep command I am using is : sysprep /generalize /oobe /shutdown /unattend:C:windowssystem32sysprep10answer.xml

When the PC boots after being sysprep it does not detect and install the drivers.

I have loaded the uncompressed drivers to C:windowsINF and created a folder called drivers. I set the permissions for pretty much anyone to have full control. If I manually point the driver install wizard to that folder they all install correctly. This previously worked in 7 32 bit without any thought.

I tried adding the driver path to Pass 2 and 5 in my answer file without any change.

View 1 Replies

Installation :: Driver Letter Change Post Sysprep?

Aug 5, 2015

Preparing upgrade to 10
Did clean install Window 7 to customize, sysprep, image, install on several duplicate PCs prior to upgrade
1st drive is SSD, 2nd is HDD
SSD partition c: os and d: virtual box
HDD e: data

wrote answer file move user and program data from c: to e:

Something happened post sysprep and partition letters switched d and e, I changed the drive letters in windows and now can't get into profile There is a shortcut to e on the d partition of SSD Tried reassigning letters using diskpart but they don't remain when entering windows but go back to the wrong assignment.

I googled this and apparently it happens but I don't know why. I can only think that I was lucky to image the clean OS however if I can fix this it would save me time. If not, I will get rid of the d: partition and put that post sysprep

Here is the answer file

< ?xml version="1.0" encoding="utf-8"?>
< unattend xmlns="urn:schemas-microsoft-com:unattend">
<settings pass="oobeSystem">
<component name="Microsoft-Windows-Shell-Setup" processorArchitecture="amd64" publicKeyToken="31bf3856ad364e35" language="neutral" versionScope="nonSxS"

[code]...

I can't seem to fix this problem

View 3 Replies

Installation :: Replace Key To Sysprep And Move Bootcamp To New MacBook Pro?

Apr 14, 2016

I upgraded my Bootcamp version of Windows 7 Ultimate to Windows 10 on my MacBook Air. The screen is cracked on my MacBook Air so I am trying to move Bootcamp to a new MacBook Pro. When I run Sysprep I am getting an error message that says Sysprep cannot run on an upgraded version of Windows.

My question is: If I purchase new Windows 10 Pro operating system, can I replace the upgraded Windows 10 product key with the new key and will it change the upgrade to a new installation of Windows 10. If it will do this, I can then run Sysprep and move Bootcamp to my new MacBook Pro.

View 2 Replies

Installation :: Sysprep / Default Apps And Windows Apps Crash?

Aug 18, 2015

I'm installing Windows 10 on new computer for my organization . I try to configure one with fresh install (package of apps like Libreoffice, VLC, etc. for users) and custom desktop describes in this tutorial:

Default User Profile - Customize in Windows 10 - Windows 10 Forums It works fine, in audit mode I install apps, drivers, custom desktop and configure default apps like google chrome for internet browser, adobe reader for pdf files etc. then I run the command line to enter oobe mode generalize. Everything is ok, I continue my install. Then I create new user local account. And when windows starts, I have my custom desktop but default apps are removed (Microsoft Edge replace Chrome, Pdf files are read with Edge, etc.) and Apps Windows like "Weather" or "Actualities" crash .

View 5 Replies

WiFi Disconnects Randomly

Aug 9, 2015

So, firstly I would like to say that I'm sure most of you have at least heard of this issue if you have never directly dealt with it yourself. This did not just start happening after I upgraded to Windows 10; in fact, it followed me from 7 to 8 to 10 now. Although, each time a new Windows is installed, the issue stops happening for a few days. But I'm getting ahead of myself.

The Problem : I can be doing anything. Listening to music, playing a game. Then suddenly, everything will stop and I'll look. Sure enough, I've been disconnected from my internet. Again, this has happened throughout Windows 7-10. All I have to do is manually reconnect, and I'm back. But usually only for a few more minutes. What I have noticed, however, is that it happens more frequently depending on what I'm doing/playing; I just don't know what makes this occur.

What I have tried : I have been trying to solve this problem for years, which obviously means I have scoured the internet, searching for every possible method that has been suggested. Here's what I've attempted:

Reformatting Windows (like I said, it goes away for a few days after a reformat/an upgrade, but it never stays away).Uninstalling my Wireless card and having Windows automatically reinstall it (this seemed to work for 30 minutes.)Playing with my router settings.Changing my Power Save plans.Playing with the Firewall settings.Uninstalling programs that seemed to be part of the problem.Searching for viruses.

Nothing was effective. And if it was at all effective, it was only temporary.

View 2 Replies

Bluetooth Disconnects WiFi?

Nov 6, 2015

Upgraded from 8.1 to Windows 10 on Lenovo laptop. Now as soon as I connect to an external Bluetooth hardware to play music my wifi disconnects - every single time! All Bluetooth and adapter drivers up to date.

View 11 Replies

Updates :: Windows Activated In Sysprep Mode From Clean Install?

Nov 16, 2015

I'm having issues with deploying out-of the box windows 10 on a Lenovo B50-80EW preinstalled win 7 pro and upgradable to win 8.1 Pro however since the new windows 10 update build 1511 ISO I download I thought it would go through OK . without have to do first upgrade install to windows 10

Secure BOOT on UEFI ON

From putting the windows 10 ISO in drive it doesn't prompt for activation key. As soon as network settings prompts I press shift/ Contro / F3

Now in administrator Mode I check windows is activated however I have the same model of laptop and I want to mass deploy an image but want to use the OEM key embedded in BIOS to each laptop of this model is this possible to be done as I deployed on another machine and got message saying this key is already in use is there an issue with the new ISO available from Microsoft .

I also tried fresh install with out no ethernet or wireless connected and still get on same machine windows is activated in audit mode on fresh setup.

View 3 Replies

Networking :: WiFi Continuously Disconnects

Jan 25, 2016

This just started happening only a few days ago, I'm not sure what might have caused it, but my laptop will suddenly disconnect from my wifi network. sometimes it won't disconnect, but just stop receiving/sending packets. I can tell this because suddenly my pages are stuck loading and skype is trying to reconnect, but nothing happens until I manually disconnect.

I have tried Troubleshooting. But I usually get "Your proxy setting could not be recognized" or something, even though I don't have any proxy settings.Uninstalling and then reinstalling the latest driver for my wifi card. Disabling power saving for the wifi card as talked about here. Everything mentioned on the Microsoft page here

Ethernet works fine. I can connect my phone to wifi and tether it to my laptop, so this shouldn't be a problem with the router.

View 1 Replies

Networking :: WiFi Disconnects Regularly

Nov 11, 2015

In my bar we have free Wi-Fi, I use it myself on my laptop (windows 10.1)

Quite often the Wi-Fi disconnects but nobody sees the router anymore. So everybody loses their connection. It's like my laptop can shut down the router for a while. After a minute or 2 it's visible again.

I also noticed that when I download something large (via torrent) it disconnects allot more.

View 3 Replies

Networking :: Automatically Disconnects From VPN Server

Oct 24, 2015

I am connecting to the VPN server with Windows 10 built-in provider using L2TP/IPsec protocol withusername/password and a Pre Shared Key. Everything is fine except the fact that every 1.5 hours it disconnects automatically. Then I have to go to VPN settings again and press the Connect button to connect to the VPN server.

My friend doesn't experience this problem while connecting to this VPN server from his MacBook. This is a very big issue, that can compromise the privacy of a user.

View 4 Replies

Networking :: WiFi Disconnects Randomly Since Update

Dec 19, 2015

Since installing the recent updates for Windows 10, every now and then my Wifi will just disconnect... Turning it back on is as simple as clicking on the Internet icon and clicking "connect" again, though I'm a gamer and when the connection drops out during games it becomes a real problem. My Wifi is set to connect automatically, but that tool seems to be ignored as it disconnects and stays disconnected until I manually click "connect".

View 4 Replies

After Upgrade RDP Disconnects - LAN Ethernet Connection Is Set To Limited

Aug 22, 2015

I upgraded to Windows 10 on my home PC and now every time I connect to this PC from another PC I can use it for a bit and then all of a sudden it disconnects and when I try to log back in it then doesn't connect anymore.

Then when I actually go to this PC again I see that my LAN Ethernet connection is set to "Limited" and I have to restart my PC to get everything back to normal.

Is my Broadcom Ethernet card not compatible with Windows 10?

View 1 Replies

Headset Just Disconnects And Videos Are Unable To Play

Aug 23, 2015

For some reason out of nowhere my headset will disconnect, and videos stop working . My headset just disconnects, and videos are unable to play. Also, sometimes the shortcut bar will also stop working when this happens. Windows 10 ...

View 1 Replies

Gaming :: Archeage - Disconnects Every Time Select A Server

Nov 17, 2015

I recently built a new PC and installed windows 10 as my operating system (some what regretting it at this moment) and i have installed a game called Archeage that worked just fine on windows 7 with no connection issues what so ever. Now with windows 10 as i try to select a server i get disconnected right away with maybe a 1/100 chance of actually connecting to the server.

Is there something i have to configure with windows 10 to allow me to connect to game servers because i find i have a similar issue with Black Ops 3 in terms of connecting to the server.

View 3 Replies

Networking :: Laptop Disconnects From WiFi At Random Intervals?

Feb 23, 2016

My laptop is randomly disconnecting from my new router. Sometimes it's every few minutes, sometimes it can be an hour or two in between disconnections. This only seems to effect wireless devices and I notice it most often on my laptop. The router is a Fritz!Box 7490 and is connected to 2degrees Internet. The message in the WLAN event log is :

Wireless LAN device deregistered itself (5 GHz). MAC address: 64:BC:0C:6A:79:62 The weird thing is that if I disconnect from wifi and reconnect it re-establishes the connection near instantly. Sometimes it just shows as connected to wifi but not to the internet.

I have tried factory resetting the router and I've tried setting my laptop DNS settings to 8.8.8.8 and 8.8.4.4. I have also tried to change the wifi channels in case of interference.

View 3 Replies

Start-up Process Disconnects Leaving Screen Black

Dec 21, 2015

Twice I have downloaded the Windows 10 Upgrade and both times the start-up process disconnects leaving my screen black. On each occasion I reverted to my Windows 8.1 OS.

View 4 Replies

Drivers/Hardware :: USB 3.0 External Hard Drive Disconnects After A Few Minutes?

Feb 10, 2016

I connect my USB 3.0 external hard drive to my laptop and it works but after a few minutes of not using it the disk stops spinning and when I to use it again my computer locks up and after 30-60 seconds it disconnects and reconnects some times. Else I have to pull it out. If I use the drive without a to long pause in between it work perfectly fine but as soon as the drive stop spinning and has to spin up that is where it happened. that feature in the power options turn on where the power to usb does not turn off.

I will look to see it I can change the hard drive shutdown time in properties.

View 9 Replies

Installation :: Black Screen After Installation (Error Code 8007002C-4000D)

Jul 30, 2015

I've tried downloading and installing Windows 10 via the System Update for the past 24 hours (I've tried it 5 separate times). Every time it gets to 84% overall, and 36% configuring settings, then goes to a black screen with nothing on it (including no cursor) and almost no HDD activity. This has happened all five times.

Windows 7 Ultimate 64bit SP1
Intel Core i7-2600 CPU
16gb Ram
AMD Radeon R9 380 Series
Single monitor

View 9 Replies

Installation :: Apple MBP / UEFI Installation Won't Boot After Image Apply

Aug 25, 2015

last few hours I spent trying to manually deploy Windows 10 on clean GPT disk but after applying image and rebooting I always end in unbootable state.

I manually setup drive like this:

Code:

select disk 0cleanconvert gptcreate partition primary size 350 #RE tools won't fit 300MB anymore :-)format quick fs ntfs label "Windows RE tools"assign letter tset id de94bba4-06d1-4d40-a16a-bfd50179d6acgpt attributes 0x8000000000000001create partition efi size 100format quick fs fat32 label Systemassign letter screate partition msr size 128create partition primary format quick fs ntfs label Windowsassign letter wlist volumeexit#no recovery image partition as per documentation it is no longer needed and followed by pretty common deployment:

Code:

dism /apply-image /imagefile:g:Sourcesinstall.wim /index:1 /applydir:w:dism /image:w: /set-Timezone:"Central Europe Standard Time"md T:RecoveryWindowsREattrib w:WindowsSystem32RecoveryWinre.wim -h -s -rcopy w:WindowsSystem32RecoveryWinre.wim T:RecoveryWindowsREwinre.wimbcdboot w:windows /s s: /f UEFIw:WindowsSystem32
eagentc /setreimage /path T:RecoveryWindowsRE /target w:Windows

After reboot I always end unbootable (as we talk Apple computer it means 1) no partition on Option or 2) folder with ? or 3) just gray screen, make your pick). There's a chance that Windows rely on some UEFI 2.0 feature, which is not available as the old guy has 1.2 only. Or maybe I missed some step somewhere.

View 2 Replies

Installation :: Installation Black Screen On Reboot - No Cursor

Sep 12, 2015

Upgrading from windows 7 to 10, started install at around 10:30am and left it....around 2:30pm it started the large circle with the % in the centre, and again left it for another hour or so and came back to a black screen, no cursor or anything.

I waited until about 7:30 and still nothing and did a reboot by holding the power button down. On restarting, I get the windows 10 logo with the spinning dots, and then it cuts to black with no cursor. The CPU light does what it would usually do on startup, and when it first cuts to black but then the screen seems to change to a different black (if that makes sense?!) and the light only blips extremely quickly with a long period before it blips again

i know this is another update gone wrong post but I can't seem to find any with the same problem, just similar ones. I've read it can take a long time, but it's been nearly 11 hours and is very frustrating!

i'm not mega pc savvy, I get 2 options when I boot, and I've looked and there's no option for me to do a safe boot, or to revert back go windows 7. If I leave it on black screen for too long it automatically goes into sleep mode.

View 4 Replies

Installation :: UEFI BIOS Settings To Prepare For Installation

Aug 31, 2015

Is it advisable to set the UEFI BIOS (Asus ROG Hero Maximus VI motherboard) to a factory default settings before installing Windows 10? Or should I at least set the memory "XMP" profile?

View 3 Replies







Copyrights 2005-15 www.BigResource.com, All rights reserved