I have created a disk image of the system disk, C: with the disk image software in Win 10 backup. The system disk was 70GB with 40GB of files. When I tried to write the image to the SSD the Win 10 install software said the disk (120GB= 110GB) was too small. I reinstalled the windows disk booted and shrank the system disk to just under 60 GB and retried the process with the same result. System is Win 10 32 bit on an old Acer netbook.I would like to be able to transfer the installed files to the SSD.I have looked at the tutorials for creating a system image and also how to create hardware independent image for installing win 10
First of all, I upgraded to windows 10 from windows 7. My device is a ASUS K55vd notebook. When I was running on windows 7 I successfully created a factory image disk via ASUS ai recovery application (a five bootable disk). Then I decided to upgrade my hdd to ssd. My idea is to have a clean factory installation of windows 7 on ssd so I didn't clone my old hdd.
What I did was mount the ssd and ran my recovery disk and successfully installed a fresh windows 7, it is then when I update my windows 7 and went to windows 10. Currently I'm running on windows 10 and there is the notification of creating a factory disk which I would like to do but as soon as I start burning the disk it says that the recovery partition does not exist even though I have my recovery drive ( R: ).
Next, I tried creating system repair disc from Control Panel>System and security>Backup and restore (windows 7) then this prompt came. "The selected disc cannot be used. The selected disc does not contain a valid Windows installation."
Lastly I tried creating system image also from Control Panel too. However it failed and says that the mounted backup volume is inaccessible.
In my reagentc /info:
In my disk management:
I would like to ask for some solution regarding that and I'm wondering if the previous factory image disc that I have from before (win 7) is still usable if I decided to factory reset my pc? And can I make a bootable disc in which it reverts my windows to the point where I freshly upgraded to windows 10 so that I would relieve myself the hassle of upgrading again to windows 10 when the factory image disc work (in which it will surely reverts my windows to win 7).
I created ISO disks for both my 32 bit and 64 bit systems at the MS download site. If I use the ISO disk instead of the Windows Update method, does the install still create the W7 image in case I want to go back to W7 after installing W10?
Also, do I boot from the disk or do I go into the ISO disk and click on Setup?
Is it permitted to install the backup image of Windows 10 to a New bigger hard disk in the same PC. After that I will use the new hard disk only and format the old one.
I am planning on installing Windows 10, and I'am thinking of doing a clean install. So my question is if I create a system image of my current OS i.e. Win 8.1 will I be able to restore it on Windows 10? Because I do not want to install every software again.
I created system image backup file at least once a week. I did one yesterday, and today I needed to run it to restore my system. To my horror, I cannot find way to run it. I ran system image backup restore multiple times. I know how to do it...... until today. Today, by the time I clicked Troubleshoot option, there is no Advanced Options to choose from. Instead it sent me to Startup Settings option where I could go to safe mode etc,
I ended up running a system restore. Good thing I do create restore point religiously. But, after system restore, I still have the same problem.......... cannot restore image by using system image backup.
adding............... I went to my other laptop running Win 10 Pro, I had no trouble running system image restore.
I hope shortly to receive a "pre-owned" Dell M6800 laptop with a 128GB Solid State Disk (SSD) and a 750GB HDD.
It comes with 8.1 installed (shudder) and I will upgrade to 10 immediately as I couldn't tolerate 8 or 8.1. Once I've done that, I'll need to transfer all my applications and data (which will be tedious I know unless there's some trick or clever tool/application to do it).
Aapart from the OS what should go on the SSD, and what on the HDD. Looking at my current system, the Windows directory plus Program Files, Program Files (x86) and Program Data run awfully close to 128GB, so this isn't quite as simple as Windows & Apps on SSD, with everything else on the HDD and use junctions if necessary to point to data on the HDD.
So I recently formatted my Windows 8.1 system and installed Windows 10. But it seems that the setup decided to set my System parition to a separate HDD (G: ) and put the bootmgr and all the boot files there, instead of using the left-over 350MB System Reserved partition on my primary SSD that Windows 8.1 had used. So of course now if I removed that disk, I wouldn't be able to boot anymore.
So what'll be the best way to move all of the boot files and system partition setting back to my old 350MB System Reserved partition? Will I need to disconnect all the other drives and do a repair install of Windows 10? Or can I manually move the files and partition settings over? The old partition is still marked as Active, so maybe I can just move all the Boot related files from G: to the 350MB partition and it'll just work? Maybe mark G: as INACTIVE too
I have 3 HDD's (2 internals (1 SSD 120 GB and 1 HDD-Sata 200 GB) and 1 external USB HDD (2 TB)). I have installed Windows 10 Pro x64 final οn the SSD 120 GB without problems and i have installed the extra programs that i use, also without problems. Then i decided to make an image backup to the external USB HDD. The image created succesfully. After that, i have removed the SSD 120 GB, installed the HDD-Sata 200 GB and tried to check to the HDD-Sata 200 GB if the Windows image recovery works. I used the Windows installation DVD and the external USB HDD to do the recovery.
The image recovered normally and the HDD works like as if i was using the SSD 120 GB. So my problem now is with the capacity of the HDD-Sata 200 GB which is shown as 120 GB. So any way to restore the capacity of that HDD again back to 200 GB? I don't want to format the disk now, just continue to use it as a backup disk just in case of failure of my SSD one. I know that i cannot use the HDD Capacity Restore Tool, because it is working only with 32-bit systems (which i currently don't have one right now) and even if i use it i don't know if it will restore my disk to full capacity but in a state that requires format from the begin (something that i am trying to avoid).
So in general, my question is how to restore the capacity of a hard disk after image recovery (when you backup to a new hard disk with capacity bigger than the capacity of the disk that i want to backup).
I found out that the hard disk is 100% utilized. In Task Manager, the process that utilizes the disk the most is ESET Service. If I open Resource Monitor there are many instances of the System process that are reading the disk, not writing it. I have two partitions on my disk - one for the system and the other one for data; the extensive disk reading is done for Pictures (I assigned a folder with pictures, about 140 GB in size, to the system My Pictures folder) on the data partition.
I am not running any tests in the ESET Endpoint Antivirus software and it seems to me that the high disk activity starts when I do not do anything and just e.g. browse Internet or look at something. So, it feels like Windows is doing something, but what it is and how I can influence it. If it were disk optimizations I think I should see also disk writes, not only reads. Could it be that Windows is doing something automatic with Pictures, Documents, etc.?
I wonder what is going on - I dislike the fact that something is going on with the hard disk, making is 100% utilized and making other work very slow and non-responsive.
Whenever I try to create a system image or run recimg I get error 12289 and the backup fails. System protection is turned on and maximum space used is set to 20%. I have no third party backup software installed and this is a real not virtual machine.
I successfully created the image to an external drive, apparently. It took some time and the moving activity bar moved to completion.Opening the drive there is no sign of the image altho there is one I created last year. Also altho it said that so much of the drive would be used the resulting free space seems the same as before the creation.It is not in my C drive so what has happened?
I had updated windows 7 home premium to windows 10 then when the update was complete I created a backup image of the whole system.... and saved in an external HD. then my fixed disk died, replaced by a new fixed HD I can not recover the backed up windows ten image from my external HD ... is that due that when replaced the new HD I am contrived to recover the system with windows 7 home premium and windows 7 do not recognize the backed image of windows 10?
I created a system image on a Seagate external hard drive using Windows 10 Home, and I created a restore disc for booting with an external BUFFALO DVD drive connected to a USB port. I went into the UEFI and set my BUFFALO drive as the first drive to be used for booting at power up or reset. When I restarted the computer, a message appeared saying "Press any key to boot from CD or DVD". I pressed a key. After a few minutes, the following screen appeared:
I used the down-arrow key to select US and hit enter. Then the following screen appeared:
I used the down-arrow key to select "Choose Device" and hit enter. Then the following screen appeared:
This screen gave me only two options: (1) Boot with the BUFFALO optical drive, and (2) Boot with the Solid State Drive which the HP Spectre x360 has (instead of a real hard drive). When I used the down arrow to select the BUFFALO optical drive, the screen that asks for the desired keyboard layout reappeared. When I selected US and hit enter, the screen that asks for a booting option reappeared. When I selected "Choose Device" and hit enter, the screen that gave me the option to boot with either my BUFFALO optical drive or the Solid State Drive reappeared. I found I could keep going around in circles like this, without ever having an opportunity to restore the computer with a system image I had created earlier.
I am trying to restore a Windows 10 system image with no luck. Here is what led up to this situation:
1. Upgraded from Windows 8.1 to Windows 10 when it became available the end of July.
2. Made a System Image (ssd m.2 mounted on the motherboard) after I was to a point where everything seemed to be working fine on 8/12/15 and saved the image to a separate hard drive on my system (E: drive).
3. Updated the bios from 2012 to 2501 yesterday and I was no longer able to boot from the ssd drive. Windows would start to load and then give me an error that no operating system was available. Tried everything I could to get Windows 10 to boot from the ssd drive with no luck (after the initial boot manager reached the point where the operating system should begin to load, all drive activity stopped)
4. Performed a System Restore saving all personal data because I could not see the system image I had created or access the original ssd partition the had original Windows 10 on it in a command prompt from within Windows RE (the drive did not exist).
5. Windows 10 now loads less all the programs I had installed.
6. When I attempt to restore the system image from advanced options in Windows 10 RE, it gets to the point of showing me available images for which there are none showing. I copied the image from the original hard drive to a USB hard drive and to a network location. Windows does not recognize the image in any of the locations.
I read in a thread somewhere that in Windows 10, the only way to restore a system with a windows system image was with the actual OS that created it. Since I did the Restore from the original system image from the recovery partition and not the one I had made the image with I am assuming that is why Windows is not showing any image to restore.
I have a custom built system:
Asus P97 Pro mobo Intel i7-4790 3.6GHz 32 GB RAM 64 bit Windows 10 SSD - Crucial CT500MX200SSD4 Hard Drives x2 - Toshiba DT01ACA300
How to get Windows 10 to recognize the image. I am going to give it about another hour of research and then do a clean install.
Windows 10 build 10586 x64. When I try to create a System Image I find that Windows 8.1 and Windows 10 are both selected. How Do I just create a system Image for Windows 10
How do I set up an external HDD to be used for system image backups? For example, specify how many images to keep, schedule the backup, etc. also, can I use the drive for anything else other than image copies?
I did a clean install of windows 10 and now i am trying to do a system image and save it to usb but windows keeps saying this is not a valid location, my usb is a sandisk 64 gb formatted to the correct format that windows asks me to do. I have tried to do create a image on two usb flash drives but i keep getting the same error from windows that this is not a valid location .
I have just created a system image to disc, and I would like to know how I go about verifying that the disc is working. When I say disk it took 5 hrs and 19 disc's to finish.
I recently purchased a Lenovo 900 ultrabook, and proceeded to upgrade from Windows 10 Home to Windows 10 Pro (using a Windows 7 Ultimate product key). Now that I have done this the factory "restore" does not include my upgrade and I am concerned that I would lose it if I ever needed to restore.
So, I am trying to do a full system image backup to a flash drive, but Windows 10 says that the drive is not allowed for this. I can create the USB drive as a network share and get the backup to work using that method, but I don't really trust that it will work properly.
How to do a full system image backup to a USB drive in Windows 10 that you trust will work in the case a restore is needed?
I've not partitioned a hard drive on Windows 8/8.1. In fact, I've never partitioned a hard drive on Windows 7. The last time I partitioned a hard drive was Windows XP to dual-boot two operating systems. I'd like to partition the hard drive on my laptop in order to save a backup of my system onto it, as I don't have an external drive right now. Any detailed, step by step process to partition my hard drive and then back up my system onto it? I have 350GB of free space.
Before I upgrade to Windows 10 on my Windows 7 desktop I'd like to know whether or not there is a built in create a backup system image?
Once my Windows 10 upgrade is running properly and before adding in any new programs I wish to create a backup system image
--- I know I can use a 3rd party program and I am use to Macrium Reflect on my Windows 7 but I wish to know whether or not there is a built in create a backup system image utility
So far I have found which I will do while my Windows upgrade is in pristine condition
