Installation :: Upgrade Stops At 24% Fails With 0xc0000f
Aug 2, 2015
Upgrade of Win7 HP laptop -- not usual failure code. Upgrade done through Windows Update (copy was reserved). Gets to 24%, restarts, bring up Recovery screen, fails with 0xc0000f -- a required device isn't connected.
Only one physical drive in the laptop -- works fine under Win7.
Have seen threads about problems with System Reserved being too small for Win10 (200MB for Win7 vs. 450MB for Win8). Tried shrinking C: and resizing System Reserved.
Repeats above problems -- plus, leaves laptop in weird mode with Win10 partially installed, a new Recovery partition, and nothing working (meaning, Win7 won't boot anymore).
Am now trying option of installing from DVD, after merging boot stuff into C: partition and removing System Reserved -- figuring that if Win10 requires a System Reserved partition, it knows how to create one the right size.
I am now getting a new error. The error i am now getting is error C1420127 windows 10 now installs almost but towards the end it stops and says error and then when i go to look at it that is what the error is.
I've successfully updated to Windows 10 on my two Surfaces, but there is some kind of issue on my desktop PC. The upgrade process from Windows 8 fails at about 71% total (Installing features and drivers at 91%), and the error I get is:
C1900101-40017 Windows Update ran into a problem.
When I click on "Get help with this error" I'm directed to a page with some general troubleshooting with Windows Update. I've run Windows update repair tool and it fixed some issues, but the installation failed again.
I have now tried freeing up more disk space which I admit was a bit tight and I'm preparing to run the update again. Still, I'd prefer if there was a more detailed error message or a log file where I could see what exactly went wrong, but there are no indications where I might find one (either in the error message, the troubleshooter, or Google). As it is, I'm shooting blind here and this will now be my fifth upgrade attempt.
I have been trying to upgrade 7pro for a day or so with no luck. First of all I tried the 'get windows 10 app' this tells me a update (KB2952664) is not installed. It was showing as failed in my update long but has since installed ok. However the app still says its missing. So I tried the media creation tool. This starts up fine but about 40 min in this screen appears
I press ok and after about 10 seconds the installer just closes, and that's it we are back to normal. I have tried this 3 times and I get the same result.
The first time, it hung at 26% total, 89% copying files. Then it bricked my system completely so I made a clean install of Windows 8.1. There was nothing else installed than Windows & Updates.
Tried to update it with a stick made by the Media Creation Tool --> Stuck at 23%, 77% copying files.
I tried everything: Disabled Network Adapter, pulled all Cables (only mouse left) out, I also detached my second HDD.
I am trying to install Win10 on my SSD (Samsung 830 Pro, 130GB). I am running a Z77 Chipset.
I'd love to install completely new with the Image but that doesn't work because of the activation later on..
I'm stuck with a fresh Windows 8.1 install now, that's not really what I wanted. I'd love to update to 10 since I had it as a Insider too.
Have followed instructions & downloaded upgrade only to find every time it gets to 32% it fails & will not go any further, have done this four times outcome always the same, I have 74gb of hard drive free so there should be enough to accommodate the upgrade.
I have made 3 attempts at upgrading my Toshiba Satellite notebook from Windows 7 home premium to windows 10. Have tried both the upgrade sent via the Microsoft message and using the media creation tool. All 3 times it stopped in configuring devices at 38%, 47% overall progress. The setuperrlog.txt is:
I reserved my copy of windows 10. I have tried to update it plenty of time but every time i do it fails during the second boot, it stops at 93% and goes to a black screen for a while, than it says "restoring back to your previous version of windows" I dont know what to do. I tried mostly everything. I deleted all the files in the software distribution and went into command prompt and put in wuauclt.exe /updatenow that didnt work. I downloaded the windows tool directly from windows that didnt work.
Although I have been notified that my upgrade is ready to install, every time I try this it fails with an error message code of '80070002'. I've followed MS instructions on how to fix but guess what - it still fails.
When upgrading to W10 it failes. W10 can't get the source disk. I think it's because i have already moved my W7 from the HDD to a ssd disk using Samsung migration program delivered with the ssd disk.
This update "Säkerhetsuppdatering för Internet Explorer Flash Player i Windows 10 Version 1511 för x64-baserade datorer (KB3119147)" (Swedish !!! but I bet You can guess my problem )stops att 95% when downloading. Have waited for hours.I have restarted several times but no diff result.
I received notification that my Windows 10 reservation is now ready. After downloading and preparing to install through Windows Update, I receive a failure notice with error code 80070005.
I am currently on Windows 8.1 Pro x64. I have administrative privileges.
For several months, I've had an ongoing issue when I run 'sfc /scannow', corrupt files are found, some of which it cannot be repaired. From the CBS.log file, I found these related to "utc.app.json". I was assured that when Microsoft sent out update for DiagTracking (KB3022345), it causes a false positive for file corruption.
Also worth noting is that I currently have my boot SSD partitioned and configured to dual boot Windows 8.1 Pro and Linux. This all works fine, and I've been told this shouldn't be a problem for upgrading to Windows 10.
I would like to do an in-place upgrade to Windows 10, not a clean install, so that I keep all of my software and settings as they are.
I followed steps for installation on SSD with UEFI Everything went well until the first restart after installation files reached 100% When screen came back it was back to original Install now screen.
I had disabled secure boot in firmware as suggested. SSD is the only drive attached at present. Should I attempt a reinstallation or are there other steps I should pursue first.
I am using a retail licensed Windows 10 Pro version installed on USB using Microsoft creation media.
Dell 8700 XPS i7 4790 processor at 3.40 Ghz 16GB memory 2 TB HDD Windows 8.1 installed presently not connected Kingston HyperX 120GB
I used the free download Windows 10 Update to go from Windows 8.1. Install went find and it comes to the login screen that says "Welcome Back". I click on the next button and a small blue circle comes up and spins but nothing happens beyond that. I unplugged external drives, cards, flash drives etc and tried a hard reboot but it still stops at the same spot. What can I do from here?
Since updating Windows 7 to Windows 10, if I try to" scan to computer" I get a message on the printer touch screen " No Connection No computer is connected" How can this be corrected?
I have a problem with downloading Windows 10 Pro .ISO file. I tried to download it two times but every time media creation tool exits suddenly when it gets 98% without any error message or something! and the process in task manager is killed automatically,
After a critical update on the 20th, my computer will no longer boot. I have tried using this method to reset, i have also tried using the repair tools to return to windows 7, which fails as well. System restore also fails. My computer didnt come with recovery disks. I called tech support and they transferred me to sales so i could buy a clean copy of windows 10. get back to windows 7. I was a fool to upgrade.
So I've been trying to update to WIN 10 a lot of times since it came out. Unfortunately the update fails around 80-90% and a BSOD shows up. The BSOD says something like Kernel Inpage Error. I've tried to update from Windows Update, the media creator tool and from the "Get Windows 10" program.
My laptop was upgraded to Windows 10 two days ago but my desktop has not received the green light yet. I was reading that if you downloaded the Media Creation Tool from Microsoft's web site that it had an option that would allow up to upgrade your PC or create an ISO install disk. I downloaded the app on my laptop and created an ISO disk as a backup in case I need to do a clean install on that platform but when I tried to run the app on my desktop it brings up the UAC prompt asking if I want to run this program and when I click Yes, nothing happens.
I read some thread somewhere that if you're having problems with this app you need to do a selective startup where you don't run any startups and you disable all of the services and after restarting, I tried this and after restarting my PC running the Media Creation app again failed to do anything .
If I run Windows Update it says I have no updates pending but it was interesting that every time I've run the Media Creation Tool it puts an entry in my update log that says the update failed. The fact is the upgrade has not failed in the normal sense only the Media Creation Tool failed.
My concern is that I have a reservation for the upgrade but that too might fail so I'd like to get my desktop upgraded to Windows 10 asap.
If I use the Window 10 Upgrade System Tray Icon to do the download then it will auto-resume with no data loss if the internet connection fails. If I try to download Win 10 Upgrade some other way then it does not have auto-resume and I'll lose the data and have to start over.
I have 3G cellular internet here in India. It is unreliable and slow and often drops out. So auto-resume is an absolute necessity if I want to successfully upgrade to Win10.
My plan is soon after I get the Win 8.1 laptop to download and install Win10. Here 3G cellular internet is slow and unreliable. I'm scared that if I try to download Win10 it will fail and I'll have to start the download from the beginning.
Someone told me that the Win10 download includes the ability to auto-resume so that if a download fails it can re-start from where it left off once the internet comes back. Is that true? I need to get confirmation on this before I get my new Win8.1 laptop.
If Win10 download really does have auto-resume capability then I can do the Win10 download and resume as needed if the download fails. without losing data.
How to confirm that Win10 download has auto-resume capability so downloaded data is not lost.
