I have updated to windows 10 automatic update , Every thing working fine except network adapter. Network adapter is missing , i can see realtek device in device manager, Mine is Dell CPU.
View 19 RepliesI have DELL Inspiron 14R N4010. Automatic upgraded to Windows 10 Home. Previously I have Windows 7 Home Premium. After upgrade I didn't see the wired network adapter. However my wifi is working fine and can access Internet. I tried to re-install the LAN driver (Atheros AR8152 PCI-E Fast Ethernet Controller Driver); it ask for upgrade/repair/de-install means driver is already present in the system. In spite of that upgraded the dirver (got the upgraded driver setup from Dell). Unfortunately, the device is still not visible in device manager.
View 4 RepliesWhats going on with my tablet (WinBook). I've installed W10 few weeks ago since then never had any problems with it, but today I noticed I cannot connect to wifi. it's gone from Network settings, if I open "connection" icon on task bar I only see Airplane mode..Network adapter from Device manager is also gone. What to do now...
I did try this - connect to internet via Bluetooth from Lumia phone and with Intel Driver Update Utility scanned tablet, only thing it found is update for Graphics driver.. what else can I do?
I cant create a virtual wifi network using this command : netsh wlan start hostednetwork (the "set" command works)
the solution is to enable Microsoft Hosted Network Virtual Adapter which is missing , and yes i tried to show hidden devices ..
Cannot access the Internet after version 10 is installed on my desktop.
View 1 RepliesMy Dell laptop which is windows 10 only has a chronic problem with the adapter constantly needing to be reset. Searching for similar problems led me to the possibility of a USB adapter.
View 1 RepliesMy computer was updated on Wed, 12/16 and my internet adapter went missing..I've been on hold with HP service for over 10 hours during past few days and would like to have this internet adapter put back on....so far, I have zero results...I have tried to do it my self but to no avail
View 5 RepliesI recently bought a TP LINK TF-3200 card because my Lan port got fried :P. But, it id getting detected but is not working as I am not able to find new drivers for it.
View 8 RepliesThis is all after upgrading from Windows 7 three days ago.
After two days of enjoying Windows 10, my internet just started going out. The pc would freeze for a sec and then id get a red x in the bottom and my wifi would be gone. In device manager, it always shows my wifi network adapter operation was unsuccessful. I switched to a different adapter and installed the latest drivers, which say are compatible with windows 10, and the same issue still happens. I also tried some CMD command I found online related to old VPNs and that didn't work.
Usually it only fixes if i unplug and replug the adapter. Disabling and enabling doesn't work. I repaired winsock and renewed tcp/ icp and that didn't work.. What can I do? I cant go 20 minutes without losing internet.
My computer just won't sleep for longer than 15 minutes, I've disabled wake-timer in the advanced power options. I also disabled my keyboard, mouse, network, adapter, and everything else in my device manager that could possibly be waking my computer up without me wanting to do so. I also checked my cmd logs for devices armed to turn my PC on.Checked the Event Viewer aswell but in the log it says whatever keeps turning my PC on is 'Unknown'.
View 1 RepliesOk so got a new usb WiFi adapter. I installed the driver first which I downloaded on my phone then transferred to my pc via usb cable. Have tried reinstalling multiple times, still won't work. I'm guessing the problem is there's no win 10 drivers for it. NOTE: I did have a old usb adapter working with no driver before but not even that's working even with drivers uninstalled. The new adapter shows up in device manager with a problem indicated with a code 10.But not in network devices.
View 1 RepliesI'm using a Linksys AE2500 network adapter on Windows 10 technical preview and when ever the adapter is plugged in, my CPU usage nearly hits 100%. I've checked for malware and that doesn't seem to be the problem.
View 1 RepliesSo after 2 failed attempts at installing Windows 10 on an Acer Aspire Z5801 PC, I finally managed to succeed. However, a new problem appeared after installation.The Wireless network adapter went completely missing. Windows does not detect its existence at all, it's like the PC doesn't have one installed. It doesn't appear in Device manager + isn't listed as an "unknown device". It's simply not there at all.The wired network adapter is there, but not wireless.
Installing the driver from Acer's website - I had to select Windows 7 64-bit as the version is all that's available for my adapter.I used a USB stick to transfer the setup files to the Acer PC. It said it successfully installed but still didn't appear, even after a reboot.Used a USB wireless adapter (Netgear) to see if it was an issue with how Windows 10 handles Wi-Fi - nope, that installed and worked fine.Scanning for Windows updates after using the USB adapter. Some updates were found and installed (no driver ones though), but still no Wi-Fi.
In the end, I reverted back to Windows 7 and what do you know? The adapter got recognised again.The USB adapter isn't a viable solution since it's required by another PC. I just used it for testing purposes.
I recently brought a new wireless network adapter for usb (Asus usb N14) and since I've started using it the connection is really unstable, I'm on the same connection on my iphone and it's just fine but on my pc it's really struggling, I've ran speed tests and it'll work fine when randomly it'll just go down, I'll still be connected to the router but have no internet. Right now looking at the wifi graph in task manager it literally going straight up for a few seconds then straight back to 0 when downloading a file, and I'm unable to download any large files because it'll just fail after about 30 seconds.
I've updated it to the latest version with no change in performance or reliability. One other thing I'm at Uni so other people will be using the connection and I've no access to the router unfortunately.
I decided to take the plunge and install win 10 on one of my machines. Used windows update to install build 10074 from windows 7.
Everything seems to have worked fine except my network adapter (onboard Realtek thing) isn't being detected.
Figured this might be a driver thing so I installed various versions of the realtek drivers both win 7 and win 8 ones and these seem to install fine but then cannot detect the card. The installer gives an error that the card may be in "Deep Sleep mode".
Once installed the Device "REaltek PCIe GBE Family Controller" appears in device manager with no issues or conflicts, but nothing is in the Network Connections window when I go through Network and Sharing centre.
I have tried booting to the trouble shooting menu and selecting load unsigned drivers but this has not worked.
I rolled back to Win 7 and the card came back and all connectivity was restored. Re-installed win10 and back to the same issue.
I have a problem with Windows 10 Network Sharing feature. It assigns fine the IP address 192.168.137.1 to the network card that acts as the bridge to connect other computers to the Internet. But it's not working, and when one goes to the share NIC adapter and right-click on it and select PROPERTIES, and then from the list of it shows one select :
"Internet Protocol Version 4 (TCP/IPv4) then you see that everything is fine, the IP address 192.168.137.1 shows there and the subnet 255.255.255.0 also there. BUT ONCE YOU CLICK ON OK in that window, another Window POPS UP and a message saying:
"The IP address 192.168.137.1 you have entered for this network adapter has already being assigned to another adapter (in parenthesis it shows the same adapter that it's assigned in the SHARING tab in the main adapter), so there is not way to get out of that 'network card properties'. further down the message in that window says: DO YOU WANT TO FIX THE PROBLEM BY CHANGING THE IP ADDRESS FOR THIS ADAPTER? and the choices are: YES or NO
The command Line in an MSDOS window run as administrator: IPCONFIG /ALL doesn't shows any other virtual or real NIC with the IP address 192.168.137.1 except for the one that was assigned in the "Sharing" tab in the properties of the real NIC that connects directly to the ISP box.
I don't know if I have explained well this issue, but all I can say it's that no other network adapter has that IP address. I have a VirtualBox virtual adapter that it has an IP address totally different, the same as another Virtual VMWare adapter.
I even went to control panel > Device Manager > Delete both NIC's (the one that connects directly to the Internet and the one that acts as the SHARING network, and the issue remains the same.
I cannot use the Wireless Router to connect my tablets or WI-FI Cellphones.
I have several Operating Systems in the Same Computer to boot with, and Windows 8.1 for instance Network Sharing works fine in the same computer.
I'm running Windows 10 PRO 64bits
OS: Windows 10 Home, 64-bit
PC: HP Pavillion g6 notebook
Network adapters: Ralink RT5390R 8-2.11bgn Wi-Fi Adapter (Date: 5/18/2015, Version: 5.0.57.0), and Realtek PCle FE Family Controller (Date: 4/01/2015, Version: 9.1.401.2015)
Problem: Every once in a while, I'll lose my internet connection. When I click the wifi icon on the taskbar, there will be no networks listed. The only way to fix the problem is to go the Device Manager, disable the Ralink Wi-Fi Adapter and then re-enable it. This fixes the problem anywhere from a of couple minutes to a couple of hours, then it happens again.
Solutions I've tried: I've tried doing a system restore but it failed and there are no more restore points. I've tried uninstalling the Ralink driver, downloading a new copy, and reinstalling it.
After kb 3081449 update i can't access internet.trbl info is
"windows couldn't automatically bind the ip protocol stack to network adapter."
I have updated Ethernet adapter and have latest wireless adapter.
Recently i have purchased my brand new hp laptop. in my laptop - Microsoft hosted virtual adapter is missing. how can i get/install/ download Microsoft hosted virtual adapter / Microsoft Virtual WiFi Miniport Adapter?
View 1 RepliesMy laptop, an Acer, has been freezing multiple times a day recently. Sometimes I get a blue screen eventually that tells me there's been a WHEA error, sometimes none of that. Yesterday, I kept staring at the screen for a while instead of restarting, and eventually it recovered. I could see the processor activity climb to 100%, and that interrupts claimed up to 14% of the activity. Afterwards, the network adapter (Qualcomm Atheros AR956x) was turned off, apparently because of a 'code 12' - 'insufficient available resources'.
That problem was only resolved after a restart. When I shut the computer down, I got a screen telling the computer was being 'prepared' for a long time - sometimes I also see a blue screen showing the installation of updates at start-up, even if none were waiting to be installed. The drivers for the network adapter are up to date, version 10.0.0.318 (apparently dating from May 2015). I'm quite sure this is a software issue - 'chkdsk' doesn't find any problems, nor does 'sfc /scannow'. And a friend of mine with an Apple laptop running Windows 10 (we've never exchanged USB sticks or anything) has exactly the same problem since installing Windows 10 (different network adapter however, and seems to have improved recently).
For the past few days I have been having the issue were an update keeps failing in windows 10 so every time it re downloads the update it tells me that my pc is going to restart in about 10 minutes regardless of what I am doing and this is about at least 3 times a dat and it is extremely annoying.
The update is a thing called "microsoft malicious software removal tool" and windows wont let me disable automatic restarts or automatic updates and i dont even need this "update" because its just a virus removal tool which I don't need but windows wont let me cancel the update.
Ever since the 1511 update last week, my SP3 display adapter crashes all the time. For example, if I'm using Windows Live Movie Maker, it will crash after only a few seconds of playback, then I have to close the app and reopen it, so I can get another 30 seconds of work done if I am lucky. If I'm using Blender or Repetier Host, it does better - lasts minutes instead of seconds, and doesn't always crash in those apps, but it does occasionally.
When I try to print to my 3D printer, it crashes sometimes, wasting plastic. I can get around that by doing the print from SD, but sometimes when it is something small, it's just easier to print from the host. Having increased problems (I used to get it occasionally, but not often) since updating to Win10 version 1511 last week?
What is the identification number of the last Windows 10 automatic update?
My installation of Windows 10 was done August 14.
The last automatic update I received was KB25533437 on August 15.
I'm aware that automatic updates via windows update cannot be disabled in windows 10 Home - does that apply to the store also.
In my Surface 3 (updated to win 10) the option to disable store updates automatically is greyed out with a message to contact my administrator (which is me!)
(I also have another win10 VM running pro where the option is not greyed out)
Laptop: HP-Pavilion Dv6-6c40ca
OS: Windows 10 (free upgrade)
Wireless adapter: Broadcom 802.11n (BCM9413HMGB)
I did the free upgrade from Windows 7 to windows 10 three weeks ago. It was a clean wipe/install and everything worked fine. I had working WiFi for three weeks.
Then I noticed windows updating itself when I powered-off the other night. The next morning my wifi was knocked out. Thew wifi symbol is still there, it just has a red circle with an x in it now. It doesn't show any networks. My other devices can 'see' over a dozen networks and can connect to my home network without issue.
Things tried:
-Uninstall/reinstall driver and restart
-"Roll Back Driver" and restart
-Download and install the latest driver from HP and restart
-Tried this solution to a tangentically related problem (that of people losing their WiFi directly after upgrading to windows 10)
Thoughts:
-the driver is very old (2012). the one from HP was uploaded in 2015 but when I click on the info I see it is issued in 2012
-Attempts to find the driver directly from Broadcom result here but these are all for Linux.. I am sure that Broadcom has windows drivers too, but how to find them?
(not sure how to link directly to image hosted on Google Drive. So this link is to a ss of my wireless adapters driver page in device manager) [URL]....
I had the upgrade to windows 10 icon in the bottom of my screen like a lot of others. But when it was time to upgrade I didn't want to because I am a gamer and don't want to upgrade before I know everything is safe (all drivers headset, gpu, mobo everything) but I clicked continue so I could accept all the conditions and such. But now it is going to upgrade automatically....
View 1 Replies