I know this problem has been discussed with many variants but not quite the same as I'm experiencing, so I'm starting a new thread.
I did a clean install of Windows 10 pro 64 bit, and everything was running perfectly, that is until two days ago when the computers on the network simply disappeared. I had done nothing with changes or new software or anything of that sort.
I checked network discovery and it was on, but the only computer showing was the home computer. I have tried turning discovery off then rebooting and then back on again and rebooting. In all cases the network drives are accessible. I have manually entered the computer name in the address bar of File Explorer eg "//COMPUTER2" and then I can go and enter the other computers manually. Everything will stay there until I close down File Explorer and then they disappear again only shown the home computer.
I just installed (yesterday) the latest W10 update that installed Version 1511 (OS Build 10586.3) and my home network consisting of five W10 PC's has been "destroyed." I do not use Homegroup. Instead, I have always set up all the drives/folders as shared on all the computers. That worked just fine until now! For some reason only one of the PC's is detected by the other PC's on the network. However, all the drives that I had previously Mapped are OK. Is there some new magic setting that I have to change to get network discovery working again ...or... is MSFT forcing me to use Homegroup?
A little more information to add to my confusion. I was wrong above - two of the PC's are shown in the Network on all the PC's. One of the five PC's, which I use as a home server, runs 24-7. For some reason it has all the other PC's showing under Network and can access all the stuff on all the PC's!! I know it used to take Windows a few minutes to find all the PC's on the Network but... all the other PC's have been running for many hours and nothing changes.
i have a killer e2400 network adaptor over a wired connection on my msi motherboard. Unfortunately, out of the blue it has stopped working. I constantly get the error message "Ethernet doesn't have a valid IP configuration." I have tried a number of things such as stopping and restarting the services in computer management. Nothing appears to work. I know my router works as I'm using it now on another computer.
I upgraded to windows 10 from 8.1, ever since then, my Huawei 173 stopped working. The led light flashes, yet the network signal is not showing, the display hangs and several other issue.
I have two desktops and a NAS drive on my network. Both PC's are Win10. One Pro, the other Home. Everything was working beautifully then out of nowhere the Home machine just stopped accessing the public folder on the Pro machine saying it didn't have permission. I thought the Public folder didn't need permissions if it's shared with Everybody. But it will access and read the other non-public shares on the Pro machine. Weird The Pro machine, however, doesn't even see the Home machine on the network any more, although I can ping it. Again, weird. I had a mapped drive to the Home machine which is now broken. Both PC's can see and access the NAS drive. No settings were changed, nothing was touched, it just worked one minute and stopped the next. The Pro machine was just updated to Build 10586.3 on 11/13/15. But I don't think that caused it because everything worked until the 17th. All the network settings were correct and they have not been changed. I can't find anything about it on the internet except the typical "Make sure Network Discovery is on and file sharing is enabled." Yes, Network Discovery is on and file and printer sharing is enabled on both machines. Still no go.
I'm not sure if it's related to the last update or not, but suddenly my homegroup started saying my other PC was offline. So I went and left it and recreated it, and sometimes it'll connect for maybe 5 minutes then disappear again. Also, it's saying almost everytime I try to join that Windows No Longer Detects a Homegroup on this network. Very strange since it's showing it. I can get to the other computer via the Network icon so it's not a disaster, but this is a frustrating issue.
after installing a replacement GPU, RDP now only connects to the home server when i have "use all my monitors" enabled.If i have it unticked the session will try to open on my second monitor - which is connected to the onboard GPU, unlike the first, which is connected to the discrete one - as usual, but blurt out a connection error after starting to render the remote desktop.If i tick "use all my monitors" in RDP settings, a connection is made, but displayed on my main screen.
I've never seen this problem with the previous O.S., Windows 7, but Windows 10 is throwing me this error message approximately 70% of the time when I run the network troubleshooter...either from the Control Panel, or by right clicking on the task bar's connection icon.
Though Win10 is the first O.S. to give me this error, the Microsoft support forums indicate that it's been fairly annoying to Windows 7 users back to 2010. Also, Microsoft support employees just give vague general tips for trying to nail down the cause.
I'm only experiencing this in EDGE. Edge sometimes freezes on a webpage when I'm attempting to post a message to a forum, similar to what I'm doing now. I run the Network Troubleshooter and get the "Native Host Has Stopped..." error. I open a new Edge tab, come to this forum and try to do a search for the answer, but this forum's search function ignores my input. So, I opened IE-11, navigate to Win10 forum, and all works well.
Experienced the "Scripted Diagnostic Native Host has Stopped Working" error when running the network troubleshooter?
I have been using this version of windows 10 from last 1 month. I installed all the drivers and everything was working just fine. From last few days my wifi driver isn't responding. I tried reinstalling the driver but the problem still exists.
I can connect through the Ethernet cable and the Bluetooth driver is also working. Only the wifi driver has stopped.
I recently set up a Homegroup on a Win10 laptop so I can see another PC on the network. That PC is running Win8.1, and I would like to use it for file backup. The devices are visible on both ends of the network and have connectivity, but when I choose to use the File Backup function from the laptop, nothing transfers and eventually I have to restart because of no response from the system. Also, my browser will stop working. I have added the PC as a network location and specified the location for backup, but is has locked up twice now. Could this be a routing issue? I previously ran the auto backup feature to a memory card, but need more space.
I have changed my router. Is a 'FritzBox fon WLAN 7170'. First i connected, it was all good, i tried to connect to browser and it was good. Then i tried to connect Steam. "Could not connect to the steam network, either check your connection and click 'Retry' or start Steam in offline mode."I looked up for the probem, tried to:
- start the shortcut with -tcp - turn the firewall off - remove Steam from processes - uninstall Steam and install it again. - delete all files from Steam (without steamapps folder)
I tried other games online, they don't work either..I saw that video - Fritz!Box Firewall Port forwarding - YouTube (is 3:22 minutes long, if you want to watch it)I saw on the internet i can connect to the router settings with WIFI connection and i can't connect (CMD - ipconfig - Default Gateway in the browser).
Do i need to port forwoard all of them ?Is the Dynamic DNS the case?Why is the IPV6 with "No network access"? -Is the IPV6 important for online games?Do i need to set IPV6 ON?
My windows 2003 server stopped working in normal mode, but working in "safe mode with networking" and giving reply from all peers, and reaching all remote locations. in Normal mode not even ping to peer and giving error "destination host unreachable". tried with new NIC. IP conflict coming when assigning used IP address, if giving a new IP address not even request going to peer showing the same error as "destination host un reachble".
Product Name: Hp Omen 15 Operating System: Microsoft Windows 10 (64-bit) Wifi card: Intel Wireless-N 7260
since some days my wifi has stopped working.If I click on Wifi icon it shows only ONE (max two) NETWORK:And I live in a building with 20+ networks, as you can see from WiFi Analyzer (I'm the red one on the right).If I deactive/reactive Wifi with fn+f12, it goes to Airplane mode and to Wifi mode again and it eventually shows all the networks/My Wifi is on the top. If it's saved, Windows connects to it and then it drops the connection; if it's not saved and I try to connect, it says "You're not able to connect to this network".The fun fact is that after some seconds every network disappear and only one is showed (probably the neighbour one..I dunno).
I've already tried to HARD-RESET the notebook keeping the power button for 10/15sec with the laptop turned off.I've already tried to follow these instructions [URL] ... updating drivers (Intel 18.12.0.3, 18.12.1.2, 18.30.0.9 [Windows 10 default], 18.32.0 [Lastest drivers]) with no success. Everytime I install a new drivers, I uninstalled the previous one + Wireless software + reboot.
I tried to uncheked "Allow this computer to turn off this device to save power" on my Wifi hardware settings without success.The HP Network support says I didn't choose a Wifi (Really? The problem is I don't see my Wifi on the list!).This is not related to a new Windows 10 upgrade since I've installed it months ago and It's the first time I've this problem :/ It always worked
I tried different settings too/I changed channel, I set 802.11g on my router, APSD off on the router.I set "Magic packet off, ad hoc QoS off, U-APSD off, fat channel off,incremental throughput off, HT mode off" on the card setting without success. Nothing chaned.The Hardware test doesn't detect any failure. If I go close to the router, it shows my network with full power connection and it connects to it. Then I go back to my bedroom (probably 3/4 meters far), it KEEPS the connection for 30/40min and It drops the connection and I can't reconnect to it anymore. It always worked perfectly in my room in these months (I bought it in March 2015), so the distance is not a problem, I'm 6/7m far from the router.In this case It shows my Network (Connected) and the neighbour network...and the other 20+ networks???
The only way I have is USB tethering with my Nexus 5.I tried the Wifi connection on Elementary Freya (Ubuntu linux based OS) and it shows 20+ networks available on the list. It has not connection problem with my Wifi, but sometimes it stops working, the webpages stop loading and I must reboot Wifi to reconnect to it (usually after 30/40min using it).What's the problem? Is my Wifi card broken?
have a problem with usb drivers according to my control panel which says it is fixing the issue and then tells me to reboot but it is not fixed. Keyboard lights up on start but when the first blue window appears it goes off. I can get into the bios ok and the keyboard works there. only one port is working (USB3). as my mouse and keyboard are usb and there is no PS2 port i am kinda cactus at the moment. Been searching for usb drivers for win 10 but not having any luck. Everything was working fine since November until yesterday.
Just upgraded to Win 10 and kept losing internet access. After troubleshooting my home network is now named "Network 2". How do I change the name to "Network 1 "?
Mic stopped working after windows 10 update. I can't raise the db levels and it does not record any sounds. Its like its muted all the time, but i cant unmute it. Its an HyperX Cloud II if that matters.
Win 10 was working well on my Toshiba Satellite.(i7 4 gig ram).Then I lost the ability to download with Cannon Camera software. This program stopped working. ( got off pictures by removing SD card and putting it direct in laptop.)Next computer slows down and run st 55 to 60 Deg C. (air temp about 23 deg and desktop computer running at 35 deg.)
Then Blue screen telling me Video_Krnl............ failed/error.Ran restore point and system worked again for a while(2 days).Now I can only get 3 to 4 minutes before blue screening and failing. Have blown out cooling fins but little to no dust as computer is only just one year old. Regularly run AVG and Wise 365 cleaner over it.
This morning when i turned on my computer the sound was not working.I reinstall all my sound drivers, i reboot my computer a lots of time, i cheked if everythings was pluged correctly and everythings was supposed to be fine but the sound don't work !
Recently i have upgraded to Windows 10 from Windows 7. Everything was fine the first hour, then all of the sudden the mouse stopped working and it was no where to be seen. The mouse that I use is an old Logitech mouse that has a ball to control the mouse. So, I plugged in another mouse and it was working, but the clicks were backwards.
Recently discovered Windows Explorer stop working. Ran SFC /ScanNow result were some flies were repaired, which directed me to C:WindowLogCBSCBS.log, nothing found there. What to do, it was only by accident I discovered it was not working, no error messages or any signs.
The start button on windows 10 has stopped working for me. It came right after I installed a new graphics card though in the days before I had noticed strange stuff like when I searched for an app and clicked on its icon within the start menu nothing would happen. File explorer, settings etc stills works but are very slow.
I Tried to connect to my 2 other PCs this morning. I just get a screen where it says it's 'Initialising Display parameters' but will not get past this screen.
Was working perfectly yesterday! I can take control of these same computers if I try it from my Linux Ubunto PC. So that rules out the network and all of the other PCs which are still on win7
