Networking :: Wireless Serves Keeps Stopping After Update
Dec 8, 2015
my laptop recently did automatic updates and I have been having problems with the WiFi. When I first turn it on every thing is fine, but after about 30 minuets or if I shut the lid and it goes to sleep the WiFi just does not work anymore. I have to go to my network adapter and run the trouble shooter which finds the Windows Wireless Serves is not running on this computer. It starts it and every thing is fine for another 30 minutes or until I shut the lid again. I have looked in services.msc and WLAN AutoConfig is running and set to automatic. I have tried uninstalling and reinstalling the driver for my wireless card.
View 1 Replies
Similar Messages:
Nov 29, 2015
I just updated my media center to version 1511 of windows 10. Via wifi, downloaded and installed ok i thought. But have found i cannot see any wireless networks. Normally about 7 up in my area.
I've tried uninstalled the device and installing it again.
I've tried checking for newer drivers, but isn't any.
I've tried resetting these in command prompt (admin) net sch advfirewall, int ip, int ipv6, winsock and rebooted afterwards.
I've tried plugging the usb wifi adapter into a different usb port.
I've tried restarting the Router. Mobile phone picks up wifi in the same room.
View 1 Replies
Oct 11, 2015
Yooooo! I have a Lenovo Y510p with modified BIOS so I could replace the crappy Intel wireless card that came with it (Intel Centrino N2230) for an Azurewave - Broadcom 4352. The experience has been good so far, the only problem I'm having is the low wireless signal with the card. I have other laptops that have higher range and strengths on the same place with older cards.
I've tried verifying (and even swapping) the cables and noted no difference. I asked on another forum and they told me that it could be that the card is not receiving enough power, but I have yet to find a settings in the BIOS or in Windows that dwindles its performance. I have recently updated the driver from Lenovo's website and it didn't improve a bit. How to improve the wireless signal?
View 9 Replies
Dec 9, 2015
I started my PC in a new premises with a Wireless modem, I have two other PC's connected.
When I started the PC it saw the wireless network and the option came up to connect and there was a tick in the "Connect Automatically" box.
I selected OK but got a message "unable to connect".
I did not get the opportunity to enter the Password/Key.
Now the PC will not connect to the Network nor will and Diagnose and repair fix anything.
BTW the Ethernet adaptor has been disabled.
The laptop I am sending this from is next to the PC so the wireless signal is okay.
View 4 Replies
Feb 10, 2016
I have just bought an HP laptop running windows 10. I cannot connect to internet wirelessly as when I select my network connection it requests username and password. (Screen shot attached)I only have a network password for my connection and have never had or been requested for a username.
We have a couple of laptops at home and they connect with password only no problem. It is only this laptop that requests both. I can find no way past it and cannot connect. It connects via cable fine but thats obviously not ideal for portable laptop.
View 9 Replies
Sep 16, 2015
We have a new (albeit old) wireless printer (HP Color laserjet CP3525) with a wireless adapter card. Computers running Windows 7 or Windows 8 could see the network and connect. All computers could then print to the printer. None of our computers running Windows 8.1 could see the network. I upgraded one computer to Windows 10. It can now see the printer network but cannot connect.
View 7 Replies
Aug 20, 2015
When I first installed Win 10 it was working great got my wifi connection working and everything now it seems I cannot get connected. I have tried several times, putting it mildly. I put in the Modem/router address and password and then I go to the site that shows you the wifi connections and mine is not there. But there are about 10 or 12 that are there. I have tried this several times like I said. And I have rebooted to see if that did anything and it made no diff.
It seems from some of the reading I have done this might be a problem caused by an update. It worked great for several days. And while I am thinking of it can you delete all those other wi fi addresses some how.
View 19 Replies
Oct 29, 2015
I was unable to connect to an older (backup) AP in Win10, but Win7 and my phone, tablet etc could connect no problem - these were connecting using WPA-TKIP, but MS now only allows WPA2-AES
So MS have removed the less secure WPA-TKIP protocol from W10 (this apparently started in W8), but they have left the even less secure WEP protocol in place!!!
I have now connected using WEP - on my router you can use a passphrase to create the hex pairs for the key, but you need to enter the actual hex characters as the key (eg 13 hex digit pairs = 26 characters to enter)
Looking at the wlan profile from the command line interface shows what the settings are...
netsh wlan>show profile plusnet2
Profile PlusNet2 on interface Wireless Network Connection 4:
====================================
Applied: All User Profile
Profile information
-------------------
Version : 1
Type : Wireless LAN
Name : PlusNet2
Control options :
Connection mode : Connect automatically
[Code]......
View 6 Replies
Dec 17, 2015
So i currently have a MSI GT80 Titan running killer wireless 1525 network adapter and am constantly seeing network drops to the point where i get an exclamation mark over my wireless icon and no activity. Connection shows connected but no speed, only until i manually disconnect and reconnect. This has been happening since earlier this week after having the laptop off for a couple days and i'm sure some updates came in from Microsoft.
Steps I've taken already to resolve this:
1. Uninstalled killer wireless software suite and installed stand alone killer driver
2. Refreshed the PC with clean windows 10 install
3. All drivers are up to date including BIOS
4. Ran ccleaner along with registry side of it
5. Memtest shows no errors
6. Hard drives show no errors
7. Connected to LAN and no drops all day
I'm not sure what else to check as this is a fairly new laptop bought back in march and doing some searching on google showed some posts about people with the same issues (different laptops/hardware) thinking it was related to Windows 10.
View 1 Replies
Oct 19, 2015
I have been connecting my PC to my router via a Ethernet cable and have had no issues but I want to move the PC to another room and run it off a wireless adapter. I tried a TP-Link USB adapter but it didn't work so I switched it for a Netgear one. That doesn't work either which makes me think there is something not right with my PC. I have installed and uninstalled multiple times, tired different USB ports but the Wireless Adapter doesn't seem to get an IP address and there are no Wireless settings in the control panel.But there are no Wireless setting and no connectivity to the Adapter.
View 3 Replies
Aug 24, 2015
Most of the time we need to boot in safe mode with Networking to fix some of the issues. In some of the windows 10 computers wireless not working in safe mode with Networking
For an example my dell 5547. Has a wireless card, Intel Ac-3160 works fine in normal mode, But in safe mode it refuses to detect any Network, I am seeing similar behavior in some other models too in windows 10
Wired Networking (ethernet) is working.
View 9 Replies
Nov 30, 2015
When I power up my laptop it connects to a network, that I don't have (xfinitywifi). I have deleted the profile, to no avail, I get to my network by cycling my wireless. Its really annoying.
View 2 Replies
Jan 15, 2016
I have two wireless networks at home, and one is faster than the other. This is because the slower one is wired to my desktop, and the modem and router are the same box. So I would like to remove the slower from machines wireless connected. I searched the forum, and got a solution, the command below, but the answer, as can be read, is that the filter does not exist in the system. I am attaching a screen that shows GVT-15DF at the list of connections.
C:Userslarau>netsh wlan delete filter permission=allow ssid="GVT-15DF" networktype=infrastructure O filtro nao existe no sistema.
View 5 Replies
Dec 16, 2015
I just bought an ASUS PCE-N53 PCI-E adapter for my PC that I built several months ago. Previously, I was just using ethernet. Put the card in my PCI-E 1 slot, and installed the drivers from the installation disc, but nothing shows up in Device Manager and I have no wireless option in my Network Connections settings. why it's not showing up, minus it being dead out of the box? I can't try it in my PCI-E 2 slot because my graphics card is in the way.
View 4 Replies
Jan 4, 2016
Yesterday I relocated our Wireless Modem to a cooler room. We live in the Philippines so these devices can get quite warm...After relocating and hooking up all the wires, cables etc. My wife's computer a Dell, would not connect to the Wireless modem. I checked and replaced all wires with new ones, and rechecked the connections, everything was okay...I use a MAC which is still working fine, and connected right away, so I know the Signal is getting out. I did the "ping" command and it is not going thru. Tried everything I know, cannot get her wireless to work. I have a Red X on her adapter, in the Network Connections dialog box, "Not Connected"...Her system uses a Broadcom 802.11n adapter, which I replaced just recently...When I registered I added all the Dell system info, CPU info etc..
View 1 Replies
Aug 8, 2015
So after 2 failed attempts at installing Windows 10 on an Acer Aspire Z5801 PC, I finally managed to succeed. However, a new problem appeared after installation.The Wireless network adapter went completely missing. Windows does not detect its existence at all, it's like the PC doesn't have one installed. It doesn't appear in Device manager + isn't listed as an "unknown device". It's simply not there at all.The wired network adapter is there, but not wireless.
Installing the driver from Acer's website - I had to select Windows 7 64-bit as the version is all that's available for my adapter.I used a USB stick to transfer the setup files to the Acer PC. It said it successfully installed but still didn't appear, even after a reboot.Used a USB wireless adapter (Netgear) to see if it was an issue with how Windows 10 handles Wi-Fi - nope, that installed and worked fine.Scanning for Windows updates after using the USB adapter. Some updates were found and installed (no driver ones though), but still no Wi-Fi.
In the end, I reverted back to Windows 7 and what do you know? The adapter got recognised again.The USB adapter isn't a viable solution since it's required by another PC. I just used it for testing purposes.
View 9 Replies
Dec 24, 2015
This didn't happen right away. They worked fine for a month or so. It is not the ISP, my ISP is very reliable, they consistently give me the bandwidth I am supposed to get. 20MB down 2MB up. The problem laptop averages 0.3MB down and 1.5MB up.
The other hosts on my home network are not having any problems. I have another Win 10 Machine that was upgraded from Win 7 that is working just fine. One Ubuntu client and one more Win 7 client.
Fixes I attempted:
I went to the HP website and applied the recommended updates.
Checked Microsoft updates - none were suggested or required.
I removed and readded the network adapter drivers. Several times.
The hardware in question is:
HP Envy 17t Laptop
OS: Windows 10 Pro Version 1511 (OS Build 10586.36)
Wireless:Broadcom BCM43142 802.11 bgn Wi-Fi Adapter driver: 6.223.215.14
Ethernet:Realtek PCIe GBE Family Controller Adapter driver: 10.1.505.2015
View 6 Replies
Oct 6, 2015
I recently brought a new wireless network adapter for usb (Asus usb N14) and since I've started using it the connection is really unstable, I'm on the same connection on my iphone and it's just fine but on my pc it's really struggling, I've ran speed tests and it'll work fine when randomly it'll just go down, I'll still be connected to the router but have no internet. Right now looking at the wifi graph in task manager it literally going straight up for a few seconds then straight back to 0 when downloading a file, and I'm unable to download any large files because it'll just fail after about 30 seconds.
I've updated it to the latest version with no change in performance or reliability. One other thing I'm at Uni so other people will be using the connection and I've no access to the router unfortunately.
View 1 Replies
Feb 10, 2016
In the last two weeks I have been experiencing something very strange with my Windows 10 Pro. When my laptop resumes from sleep the Wireless is turned off in Windows. I don't believe it was an update because I have defer updates enabled. Unfortunately, I just noticed System Restore was turned off.
1) I have checked the power settings in Device Manager and the device is NOT checked to use power management)
2) I have updated to the latest wireless driver available.
Edit: I believe this issue has something specifically to do with Sleep because when I reboot or shutdown/power-on the Wireless is enabled and working fine. It only seems to be when Windows goes into sleep mode.
View 8 Replies
Dec 20, 2015
I have several computers, one laptop recently has a new problem. The internet network connection in the corner has a tiny yellow triangle and says the connection is limited and says it is NOT connected to the internet - even though it IS connected to the internet. It does this for both the wireless icon and the ethernet icon, so it can't be a driver issue.
I have rolled back the drivers, gone to the HP support site to get their drivers, updated to the latest drivers, and nothing gets rid of those triangles.
It's also not a router issue, because I have another computer on the same router with no problem on either the wifi or ethernet. I've done sfc /scannow in both safe mode and normal mode. I've looked for any errors and there are none. It is very annoying.
View 3 Replies
Feb 2, 2016
I'm currently running Windows 10 (directly upgraded from 7) on a Lenovo G780. The update in general has been a bit of a nightmare and I've had a number of problems, but now I'm having problems that I'm not even sure are related to windows 10 and my computer is becoming borderline unusable, which is a concern as I use it for work. I've updated all the drivers, and in fact I've managed to temporarily fix some of these problems only for them to come back again. These are the main problems I've been having:
- Start menu is only intermittently working, once it stops I have to restart to get it working again.
- Disk usage in task manager is often at 99%, and when it isn't it's still usually about 50%. Computer often crashes as a result.
- Sound keeps stopping, but in very strange ways. For example I'll be listening to music on itunes or youtube, and the music will suddenly stop, and the timer on the song will stop moving (rather than just the sound muting), it's as if the computer stops attempting to create sound. Again, this is usually only fixed by restarting.
- Computer sometimes won't turn off, for example when I shut it down from the start menu it starts closing all my programmes and then just stops without turning off. If I turn it off manually by holding the button, it starts up again as soon as I let go of the button. V strange. I've had to take the battery out a couple of times.
I've tried lots of solutions from people on the internet, I've scanned with Avast, Hitmanpro, Rkill, MBAM, Spyware, CCleaner etc. I've rolled back to before updates, I've then re-done said updates. I've done driver scanning software etc.
View 7 Replies
Jul 31, 2015
I am upgrading from 8.1 to windows 10 on an I7 laptop but when installing it crashes at 32%. I have tried three times with the same result.
View 1 Replies
Jan 17, 2016
How do I stop automatic W10 updates? Every time I have an update downloaded thing fall apart. Either Outlook stops working (Outlook not available try again later) or my Favorites bar disappears and has to be redefined, or like now, my Adobe is all sc.... up and I cannot delete adobe files or access my adobe files when I am travelling and off line. This Windows 10 is the worst mess I have ever seen in 61 years of IT/IS/Data Processing. My next PC will definitely be a MAC.
View 1 Replies
Jan 25, 2016
Have my computer hooked to my LG TV via HDMI cable. When I watch a movie it keeps stopping every so often because the buffer cannot keep up with the movie. Am using a Linksys N router with an HP All in One 23-Q129 computer.
View 19 Replies
Aug 30, 2015
After downloading windows 10 . i can't view any videos without them stopping.
View 3 Replies
Jul 31, 2015
The service is starting at boot up but then stops. I can manually start the service and it starts but then stops unexpectedly in less than a minute. Here is the event viewer log. may need to recover to Win8.1 as I need printers.
Update... I have 3 PC's (2 laptops, 1 HP & 1 Dell & 1 Dell Desktop). The Dell Desktop printers are working fine but the printer spooler service on both laptops starts and stops unexpectedly. Tried unchecking fast startup under Power and on one laptop tried LPD Print Service & LPR Port Monitor under turn Windows features on under Control Panel Programs & Features..
View 5 Replies
