Networking :: Workgroup Can't Connect To HTPC
Dec 13, 2015
I have 3 pc's in my LAN
Mark= Win7 32 bit
Dave= Win10 32 bit
HTPC = Win10 64 bit
I'm trying to share the files on HTPC and have created a workgroup.
Dave and Mark can share files
Mark and HTPC can share files
But Dave who can connect to the win7 pc through the workgroup can't connect to HTPC. Error is Windows can't communicate with the device or resource (HTPC). The computer or service you are trying to reach might be temporarily unavailable. If the device or resource is nearby and you have access to it, make sure it is turned on and connected to the network.
Since the win7 pc can connect to the win10 HTPC why can't the win10 pc?
View 8 Replies
Similar Messages:
Jun 24, 2015
I'm finding Windows 10 enjoyable and pleasant for the most part.
Unfortunately, some things that are easy to find or to do (probably due to years of experience) in Windows 7 and 8/8.1 are not easy to find, assuming they exist at all, in Windows 10 build 10130. For instance, I've looked high and low for "Change PC Settings" and it is like the proverbial needle in the haystack.
My present problem is that I can't see other computers in my network/workgroup. They are visible to my Windows 7 and 8.1 computers. My network is set to private in Windows 10. Find devices is set to on.
I note that I can ping all my devices, Squeezeboxes, WDMycloud hard disk, chromecast, computers etc., and the squeezeboxes, Logitech Media Server , WDMYcloud and Chromecast are showing up as devices.
View 9 Replies
Nov 18, 2015
Drive C: on a new win10 laptop is marked Shared for Everyone, read+write+control (because it will hold a webserver and database server that must be manageable from other workstations in the workgroup).
Yet win10 refuses access to a map-network-drive request from File Explorer run as administrator on any win7 machine in the same workgroup.
View 3 Replies
Oct 17, 2015
I have a workgroup on desktop and laptop both running windows 10 - it was functioning not long ago but recently stopped and i cant figure out why. i've pfoofed round so much trying to get it going again i've probably made it worse
I just want to access some files between computers and connect to printer attached to desktop
I can ping desktop from laptop but not reverse desktop to laptop - kaspersky is on both machines.
I tried setting up a homegroup but no luck there either - both machines can still access the internet thru netgear cgd24nv3.
View 9 Replies
Jan 21, 2016
We have a peer to peer network, with one Win 10 machine (acting as server - which we call server) which shares several hard drives for everyone in the office to access. It has network discovery on, file and printer sharing on, turn off password protected sharing off. It has all the drives named and shared properly so everyone has full access. All the other Win 7, and Win 8 machines have complete access as designed.
Another Win 10 machine has complete access as designed. All machines are part of the same workgroup Engineer. My machine is a Lenovo laptop which was upgraded from Win 8 to Win 10. When I try to access the Win 10 machine (which is acting as server), I get the Enter Network credentials pop-up asking for Username and Password which we do not use nor have ever set up on the Win 10 machine or any other. I know that there are several posts that have the Enter Network credentials popping up, but the difference is that their screenshot showed them as part of a workgroup.
See the following:
When I get the same pop-up on my Lenovo Laptop It looks like the following ....
My System Properties information ....
Notice that the example above which is part of the workgroup has no reference to a domain. My pop-up on the Laptop shows reference to a domain, and whats interesting is that the domain is the computer name of the laptop itself. There are no domains set up on any machine of our peer to peer network.
View 2 Replies
Nov 10, 2015
I have so far avoided using Windows ID login (except on a sacrificial VM I use for Windows Insider(*)) as I can no longer access the SMB shares that I have set up.
Is there any way for the two to co-exist? I can't get my head round using SMB shares and NTFS permissions with Windows Live ID - is it possible in any way at all, or have MS (as usual) given us a "new spiffy improved thing" which is actually none of the above?
Why can't I use a local login AND have have access to the Insider programme?
View 3 Replies
Jul 28, 2015
I want to clean install Windows 10 on my HTPC and remain an insider. Will it ask for a product key? Can I use my 8.1 product key? I found an ISO that I am going to try so that I don't have to install 8.1 and 1,000 updates.
View 2 Replies
Feb 23, 2016
I am on windows 10, tried to map my NAS using map network drive but says "Windows cannot access Nas102 check spelling or might be problem with your network. Next, I tried to map a specific folder inside Nas102 and it worked! For example Nas102Music I also tried to make a fake folder name and map that for example, Nas102FakeFolder and the error said check spelling of "fakefolder" Nas102 was detected but not the fakefolder. trying to connect to the whole NAS instead of just mapping individual folders inside of the NAS.
View 9 Replies
Dec 4, 2015
Today, while having lunch at my favorite restaurant, I tried to connect to their WiFi network as I usually do. I got the following message:Checking network resources.And then, after a few seconds: Can't connect to this network. My obvious question is, why not? To begin with, was it something wrong with my computer, or something wrong with their network?
For example:
DHCP server did not respond
DHCP server did not issue an IP addressStored password incorrect; enter new password: _________
WiFi adapter card not respondingInsufficient virtual memory
But no, none of that useful information was offered. How am I supposed to fix the problem?
View 2 Replies
Oct 17, 2015
There are a few networks I cannot connect to and I'm not sure why. Most networks like the one I have at home, I am able to connect, however when I am at my friend's house or some cafe, it doesn't let me connect to the internet. I tried updating my drivers and it still doesn't connect. It was able to connect few months ago when I had windows 8.1 but when I upgraded to windows 10, I started facing these problems.
It doesn't tell me what to problem is either. It just says "Cannot connect to network"
View 3 Replies
Jan 2, 2016
I have set up a Homegroup on two laptops which use Windows 10 and both connect to the Homegroup. However, neither will display any computers on the Homegroup.I have tried all sorts of things but all I seem to get from the Homegroup trouble shooter is that there are network problems. I have tried changing the advanced sharing options on both laptops to:
1. Turn on network discovery and ticking automatic setup ....
2. Turn on file and printer sharing
3. Allow windows to manage ....
Then clicking save changes.When I go back into the screen the radio button that I selected for turn on network discovery has been deselected and the turn off button selected. Nothing seems to make any difference!
View 1 Replies
Feb 10, 2016
Ever since I got my computer (which came with Windows 10), I've had trouble connecting to the internet. Every time I shut down and start it up again, it's never online even though I'm using a cat 5 cable hooked directly to the source. My laptop can connect wirelessly, so that's how I know my internet is fine, but it's a Mac (which I'm currently using) so it's a completely different OS.
Usually if I went into the command prompt and did ipconfig /release then /renew, it fixes it, and I'm online. But ever since doing a recent Windows Update that trick doesn't seem to be working anymore. I.E. ipv4 and ipv6 are enabled, tried turning off Firewall temporarily to see if that was the issue, tried uninstalling antivirus software.
View 1 Replies
Oct 31, 2015
i have tried connecting to my school's apartment however it always goes to no connections are available and then airplane mode and shows connections are available. the Wi-Fi connects just fine in all other areas of the school byt not in my apartment. The apartment is located inside the school and there are a couple of access points. I can connect to my friends Wii-U just fine but not my laptop? And when I troubleshoot, it says "Problem with router or access point.
View 1 Replies
Dec 30, 2015
So i recently updated to windows 10, and i noticed i wasn't connected to my Ethernet anymore, so i had to connect my PC to the wifi. Under my "network Adapters" it only shows "Qualcomm Atheros 802.11 1/b/g/n" I tried connecting another ethernet cable, but nothing happened.
View 1 Replies
Jan 11, 2016
I cannot seem to connect on Ethernet though Wi-Fi works OK. I have seen several articles about ethernet problems with Win10.
CABLING
First the network config:
Two notebooks, C and D are plugged into a switch and the switch plugged into the router. Now, the cabling is verified to work because computer C, running Win7 connects just fine and if the internet cables are swapped, computer C still connects just fine.
Computer D however does not connect. I did some other things to redundantly check too, just FYI.
So cabling looks OK.
ROUTER
both computers have fixed (reserved) IP addresses in the router.
The router sees computer C
but not computer D
Just FYI, if I turn on Wi-Fi, the router sees D on WiFi, but not the ethernet.
PING
Computer C can ping D
Computer D can ping C
Computer C can ping the router
Computer D cannot ping the router
Some investigation suggested the following, all of which I tried with no better results:
- Update the network adapter drivers (already current)
- Winsock posible culprit, so NETSH WINSOCK RESET and reboot - no change
IE used to find and fix these things pretty well, but here we have EDGE. Perhaps I'll try to install IE. Connectivity diagnostics are where IE shined over Chrome and Mozilla.
UPDATE: IE 9, 10, etc. are not compatible with Windows 10. So, the connectivity diagnostics just not as good in Win10. I can tell I am getting tired, as it's getting hard not to swear.
UPDATE: Added a pretty picture.
View 9 Replies
Feb 22, 2016
I upgraded to Windows 10 two months ago. Last week, I lost networking. I've scanned the posts and haven't found a solution.
Network troubleshooter says adapter might be the problem, device manager shows adapter working normally. Power saving not enabled. No VPN installed. Original adapter is Broadcomn NetLink Gigabit Ethernet.
Too late to roll back to Windows 7.
Installed new Realtek PCIe GBE Ethernet adapter that is Windows 10 compatible. Tried an old USB Netgear wireless approach.
Cannot connect desktop to network at all. All other tablets, laptops work fine.
Tried all suggested command prompts (netsh, etc).
Tried updating drivers by downloading to tablet and then transferring to computer.
View 4 Replies
Nov 16, 2015
Have 4 computers & NAS on the "Workgroup" within a private network. Most are using static IP addressing, one is using DHCP.
Two are Windows 7 machines, two have been upgraded to Windows 10.
The "Network" on the windows 7 machines show everything including the windows 10 machines and the NAS.
Both of the Windows 10 machines show both of the windows 7 machines but not the other windows 10 machine nor the NAS.
The NAS can be connected to the windows 10 machines using the app even though they do not show up on the windows 10 machines "Network". (Not a real problem & has been addressed in other forums)
When ARP -a is run on any of the Windows 7 or 10 machines, all the other IP addresses are there including the NAS.
All of the machines can ping the other IP addresses on the network.
It would seem that something in the Windows 10 OS is not allowing the other Windows 10 machine to show up in "Network".
Windows 10 appears to be a great upgrade even without the network mapping feature that was in windows 7 nor showing the NAS.
Prior to upgrading the 2 windows 7 machines (now on windows 10) to windows 10, everything was working just fine. Four computers and the NAS were showing up in "Network" and connectivity was excellent.
Before I convert the remaining two Windows 7 machines to Windows 10, I must know just what is causing this issue and the solution. The inability to communicate between these two computers, if not solvable, is a deal breaker.
View 1 Replies
Apr 14, 2016
Title says it all.
View 5 Replies
Nov 7, 2015
Can't connect to broadband connection... The Modem (or other connecting devices) has reported an error
While I troubleshooted in network and sharing center I got:
There might be a problem with the driver for the Ethernet adapter
And
There might be a problem with the driver for the wi-fi adaptor
I am using Windows 10...
View 3 Replies
Nov 21, 2015
There seem to be a lot of these problems and they are posted all over.
Firstly most of my programs that were carried over from my windows 10 upgrade seem to have some form of internet connectivity problems, my browsers work completely fine, with the exception of internet explorer, which I think is the reason for the connectivity problems, it also seems that I cannot install java, that was a possible solution that came up in a different forum. error says: cannot install java with current internet settings. The other programs that have connectivity problems are steam, bluestacks and Microsoft office 365, and that it cannot verify my licence I am currently reinstalling it to see if this solves it. will post it here if it has been solved. I use to have comodo antivrus before upgrading to windows 10, I am unsure if there are any remnants of it hiding that is causing these problems.
View 5 Replies
Dec 9, 2015
I started my PC in a new premises with a Wireless modem, I have two other PC's connected.
When I started the PC it saw the wireless network and the option came up to connect and there was a tick in the "Connect Automatically" box.
I selected OK but got a message "unable to connect".
I did not get the opportunity to enter the Password/Key.
Now the PC will not connect to the Network nor will and Diagnose and repair fix anything.
BTW the Ethernet adaptor has been disabled.
The laptop I am sending this from is next to the PC so the wireless signal is okay.
View 4 Replies
Feb 10, 2016
I have a Windows 10 Pro 64bit box as my NAS
Storage Spaces, ReFS, 2 drives mirrored
HomeGroup
HDD sleep on idle
Hibernate/Sleep disabled
My problem is when I typically save or open a file with the Windows file dialog on any Windows 10 machine, and I try to go to that machine through the network path //MyNAS/MyFiles, it initially gives me a cannot connect or find error.Is this due to the dialog not waking up the drives on the NAS? Something is obviously asleep here, and I usually end up opening Total Commander or Windows Explorer to "wake up" the connection and then everything works. I don't mind waiting, but I'd like the dialogs to hold tight until it connects, not give me not found or cannot connect.
View 1 Replies
Feb 10, 2016
I have just bought an HP laptop running windows 10. I cannot connect to internet wirelessly as when I select my network connection it requests username and password. (Screen shot attached)I only have a network password for my connection and have never had or been requested for a username.
We have a couple of laptops at home and they connect with password only no problem. It is only this laptop that requests both. I can find no way past it and cannot connect. It connects via cable fine but thats obviously not ideal for portable laptop.
View 9 Replies
Oct 23, 2015
I purchased a new computer running Windows 10 (build 10240) today and have set up the windows. However, it will not allow me to connect to my WiFi. When I use the network option in the task bar, no wifi networks are shown and it says that there are no connections available. When I access the network settings, where the different sections are listed on the left-hand side, WiFi is not an available option.
Updating drivers Deleting drivers and then allowing the computer to reinstall A few different command prompt methods such as resetting the TCP stack, as well as trying some that were for people who upgraded from windows 7/8.
View 5 Replies
Oct 17, 2015
I have a PC out in my building and it runs off wifi, sometimes my modem shuts down and reboots but it will take like 5-10 minutes unless I go all the way back to the house and power cycle it. The problem is my windows 10 is set to auto connect to it but never does unless I click the wifi drop down list then it will reconnect, any application that tries to reconnect to a specific wifi more aggressively than windows 10 it gets annoying because if I need to use the pc I cant just look across the room to see if my modem is back.
View 4 Replies
Jan 19, 2016
I've scoured the web and pulled together enough info to enable me to create an incoming VPN connection on our dedicated P2P file "server" which runs Windows 8.1 Pro. On my Windows 10 Pro laptop, I've also created an outgoing VPN connection to the server. When I click the "Connect" button in "Network and Internet" Settings, the connection is established immediately with no error messages and a resulting status of "Connected". On the server side, the incoming connection also shows connected. Sounds like success, but no matter what I try, I can't find a way to actually access any of the drives/files on the server.
I expected the server to show up in the list of "Network" computers, thereby enabling me to map a drive to the shared folder(s), but no such luck. I made sure when I was creating the incoming connection on the server that I enabled "File and Printer Sharing", as well. Also, FYI, the server's WAN connection is on a static IP, and I've done the necessary port forwarding to the server's internal IP address. The one especially odd thing is that when I view the connection details on my laptop, it shows a subnet address of 255.255.255.255, and I don't have a clue whether or not that's correct. There's oddly little information that I can find that describes all of the possible entries that are required in the many and various dialogues that are presented while trying to setup the VPN.
View 1 Replies
