No Video Signal After Upgrade (ASUS GTX 650 Ti Boost)
Jul 30, 2015
I was installing everything with relative ease so I left my computer unattended. When I came back, the computer had restarted and sounded fine except there was no video output. (I aIso couldn't hear the hard drive spinning), thinking this was normal, let it sit for about 3 hours before I got suspicious. So I tried all of the available video ports (except displayport) and none of them had a signal. I let it sit for about 2 more hours, still, nothing. So I tried turning it of and back on again. Still, nothing.
View 1 Replies
Similar Messages:
Nov 29, 2015
Upgraded my system to Windows 10 from 8.1. ASRock Z170 Gaming K4, i7-6700k, 16Gb DDR4, GTX980Ti, 958.87 Win 10 drivers (was using the same version win 8.1 driver) 3 Asus 24" monitors connected with display port to HDMI cables.
After a few minutes of not touching the keyboard or mouse, the monitors appear to have the signal stop being sent but I can see the LED backlights are still on so the screens have a glow, they are not black. As I have a TV tuner card in my system and usually have one monitor showing TV having all 3 screens lose the signal from the video card is a pain. Power setting is set to turn screens off after an hour of inactivity but this issue seems to be the video signal getting shut down.
So is this a Windows 10 or nVidia driver issue? Did not do this with 8.1 with the same driver version.
View 3 Replies
Feb 10, 2016
I have an Asus AiO ET2221A upgraded from Win8.1 to 10 3 months ago, and today only boots into the EUFI BIOS screen. There are no errors reported on Boot, just the BIOS screen
I was able to run Memtest from a DVD - fine, but couldn't boot into Hirens on USB or DVD. The BIOS does list the hdd partitions, plus I can search the hdd partitions/folders from within BIOS(!!).
I did remove and run Chkldsk on anther PC which showed/replaced several errors (20 bad sectors). I also loaded the latest BIOS download onto the hdd which in theory I can access from within BIOS. However after replacing the hdd after the chkdsk repair, it still wouldn't boot into Windows.
I am surprised as I would expect the BIOS to report it can't find the Windows (if it is the disk), rather than stick in BIOS without any diagnostics.
So I am still in a quandary as to whether this is a BIOS issue and/or a HDD issue, plus by upgrading from 8.1 to 10 the latter usually corrupts the Windows (8.1) recovery partition.
I am no expert on EUFI BIOS, but I understand that the Windows License is stored within the BIOS. If I try and re-install the BIOS is the license retained? And from that could I also re-install WIndows 10 from a download?
Edit: since posting I have got the system to boot into Hirens, but as soon as XP starts to load it turns off the USB mouse/keyboard so becomes useless. All I did was to switch off secure boot, and specify the boot order, either optical or USB. Progress but not sure what it tells me, or how I can get the usb mouse to work in Hirens in a eufi system (not had this issue before with non-eufi systems).
View 9 Replies
Sep 24, 2015
Some weeks ago I upgraded my son's Zenbook. Initially it seemed to work fine. So I did a clean install. I can vaguely remember an odd miss start-up after the clean install.It seemed to work allright after that. Anyway my son skyped a couple of weeks ago to say it isn't working. Generally speaking, can I fresh install the original W7, it was home premium. I haven't a disk and wonder if there are any ISO's available at MS for download?
View 5 Replies
Dec 10, 2015
Having Windows 10! automatically upgraded the computer Operating System (OS) you find your ASUS Motherboard has become inaccessible due to no mouse or keyboard controls. You may also find your BIOS/UEFI is inaccessible or refuses to start.
First, if you have ASUS AI Suite versions 2 or 3 when Windows 10 installed and ASUS had USB+ power controlled app, then Windows 10 on starting disables all USB 2 and 3 ports. Only solution is crash the computer 2 or 3 times whilst Windows 10 is loading the basic system; I did this by holding down the power on button for more than 6 seconds. after the computer tries to reboot the third (3) time it should start with an accessible screen asking for the user to input a decision how to reboot.
Two Options; 1. start in safe mode and hack ASUS AI Suite by manually uninstalling the program. 2. Revert to Windows 7 and uninstall AI Suite correctly.
Second, if you cannot access BIOS/UEFI, it is because Windows 10 loaded something into the motherboard active memory; to recover switch off or remove mains power and wait until BIOS goes to battery backup; about 5 minutes. If you have additional graphics cards like I have, switch off power until the LED's on the cards go out. Then switch mains power back on and you should be able to access the BIOS/UEFI with the delete key before Windows 10 logo starts.
View 1 Replies
Aug 6, 2015
I have an Asus Vivobook. In windows 8 I used sleep mode all the time. after the upgrade to windows 10 whenever the computer enters sleep mode either by closing the lid, automated or manual, when I wake it it restarts. I entered the BIOS and the AHPC mode was enabled, and was the only option. I looked through the computer power options, but I can't find anything.
View 1 Replies
Sep 11, 2015
I just upgraded my htpc computer from win7 to win10 this morning. I have an Asus P7H55 motherboard with onboard Intel HD graphics H55 series. things were not perfect to start with.
Situation before the upgrade:
- if I was watching a moving in full screen on Netflix and went away forgetting to come back to the main web page, 9/10 when I would come back to the PC, the TV would somehow have forgotten it was connected and flash as it had lost its signal. I had to hard-reboot the computer, then the problem was fixed until next time. I never was able to figure out why it did that - overheating? incompatibility when going to idle / screensaver if in full screen? was it specific to the TV? I just went with it.
Situation after the upgrade:
Now, the TV just won't display the computer, period. I know something changed during the install of win10 - as the TV screen suddenly went dark then an error message "incompatible" started showing at the bottom of the screen.
What I tried so far:
- I went on Asus' website to try to download windows 10 drivers. Somehow they seem to have forgotten putting them on their website. The 8.1 ones dont work either.
- I tried downloading stuff from Intel (they provide the chipset and graph card) but so far haven't had much success
What I'd like to avoid:
- in some research, I found that some people had to connect using VGA instead of HDMI to fix this problem with their Sony Bravia TV. I'm not thrilled with this idea as the resolution and quality would degrade compared to HDMI.
- if at all possible I'd also like to avoid having to purchase a brand new graph card for this computer.
My setup:
motherboard: asus p7h55
tv: sony bravia
View 1 Replies
Feb 10, 2016
The other day, I tried to do a factory reset on my laptop, but it failed, and I could only click cancel. Now, when I booted up my computer, it goes to the ASUS logo, then a black screen, still backlit, with an underscore flashing in the upper left corner of the screen. I can access the BIOS, and have been trying to do boot overrides. I don't have the ASUS Recovery partition installed on the laptop, and I don't have any possible ways to install an ISO. T
View 2 Replies
Feb 10, 2016
i have a corsair h100 from 2012 that has been acting weirdly. it randomly boosts itself high rpm then back to normal and sometimes turns itself off. i have to shut down my computer then start it for the h100 to turn on again.
i've checked the wires and im sure they are fine. since a restart does not make the h100 to turn on again.
is this normal wear and tear on something like a processor cooler that is 4 years old? should i rma if the warranty still active?
View 1 Replies
Oct 3, 2015
So, I was chatting with Microsoft about an issue with OneDrive, and all of a sudden my computer crashes. The error says "KERNEL AUTO BOOST LOCK WITH RAISED IRQL". I have included the dump log in this thread.
DESKTOP-CS4PJG9-Sat_10_03_2015_121137_66.zip
View 6 Replies
Aug 14, 2015
I upgraded my Lenovo U310 laptop from Windows 8.1 to Windows 10 a week ago. Everything seems to have upgraded successfully. The only problem that I can find is that none of the video streaming from Windows 10 apps can be played. I get an error 'Unsupported video type or invalid file path' when I click on a video article in USA Today or when I try to stream video from any other apps, NBC News, MSN Money, etc... from Windows 10 store.
I have no issue streaming videos from any of the browser though. What could be missing that could cause video streaming to fail?
View 1 Replies
Dec 20, 2015
Since installing Windows 10 my video picture is upside down and there is no sound. I can see the other party correctly but neither of us can hear. I have uninstalled and reinstalled Windows 10. Windows Media Player works ok. Skype Echo 123 doesn't work.
View 2 Replies
Sep 1, 2015
Basically, after installing windows 10 I turn on the computer, and it works. But my TV which I run through HDMI to my computer shows and says "no signal". SIDE NOTE: when I turn on my computer my computer runs awfully quiet. For a few seconds I hear something get loud but then it dies down.
View 1 Replies
Oct 11, 2015
Yooooo! I have a Lenovo Y510p with modified BIOS so I could replace the crappy Intel wireless card that came with it (Intel Centrino N2230) for an Azurewave - Broadcom 4352. The experience has been good so far, the only problem I'm having is the low wireless signal with the card. I have other laptops that have higher range and strengths on the same place with older cards.
I've tried verifying (and even swapping) the cables and noted no difference. I asked on another forum and they told me that it could be that the card is not receiving enough power, but I have yet to find a settings in the BIOS or in Windows that dwindles its performance. I have recently updated the driver from Lenovo's website and it didn't improve a bit. How to improve the wireless signal?
View 9 Replies
Jan 25, 2016
Sometimes when turning pc on I get a popup saying input signal out of range change settings to 1600x900-60hz and when pc comes on everything is magnified then after rebooting several times screen returns to normal?
View 1 Replies
Feb 23, 2016
Sometimes when I'm gaming online my connection gets lost and my wifi gives me no internet signal but there is internet on my other devices, I solve it by clicking on airplane mode twice (on and off again ) then the Internet comes back . Is there a permanent solution to this ?
View 1 Replies
Aug 5, 2015
last night i started the auto upsate to Windows 10 from windows 8 and It restarteded a few Times and everything seemed Good, so i went to sleep and leet the computer run.
So when i Woke up this morning i went to the computer to test Windows 10 now when i tought IT Was installed. But nothing happen so i tried to restart but still No signal. I have tried to restart the bios from cmos battery but still nothing.
View 2 Replies
Dec 21, 2015
After upgrading from windows 8.1 to 10, my monitor stopped working, showing a "no signal" error then popping to black screen. The computer works I can hear it running when I power on, but the monitor shows nothing.
I tried to remove the CMOS battery for a few minutes (something I read from another thread), but didn't work.
Specs:
Operating System
Windows 8.1 64-bit
CPU
Intel Core i5 4690K @ 3.50GHz
Haswell 22nm Technology
RAM
16.0GB Dual-Channel DDR3 @ 666MHz (9-9-9-24)
Motherboard
Gigabyte Technology Co., Ltd. H97-D3H-CF (SOCKET 0)
Graphics
22M45 (1920x1080@60Hz)
Intel HD Graphics 4600 (Gigabyte)
4095MB NVIDIA GeForce GTX 760 (Gigabyte)
Storage
1863GB Seagate ST2000DX001-1CM164 (SATA)
View 1 Replies
Jan 20, 2016
saw other post about Crashing without BSOD, and i followede some of the steps other people had to no luck. screen turns black, says no signal(one says no VGA and other say no HDMI), sounds cuts off, PC is still on, Lights in mouse and keyboard have to shut down the pc manual no BSOD.
ad the problem for some time now. first time i got them was in the Starcraft 2 legacy of the void, in some of the cutscenes, but only in the cutscenes, and now i have it again in blade and soul. sometimes at the login and sometimes when i enter the game(Cutscene). URL....starcraft was random times some cutscens were ok, some not, What i did was instant esc and watchede the cutscene online if it crashede) every other game i played/tryed i never crashede like this. WoW fallout 4 so on.
specs:
GPU: AMD radeon HD 7950 3GB
CPU:Intel Core i5-3570 @ 3.40GHz
Ram: 8GB ddr3 1333MHz
hard drive(s) 1: Samsung SSD 840 series 250GB
hard drive(s) 2: 500GB (SATA 6Gb/s) 7200RPM
mainboard: ASUS P8B75-M
PSU:XFX PRO XPS-550W-SEW
Windows: 10.
what i have try'ed so far. update all drivers,(also BIOS)removing mouse/keyborad/headset from usb(when the game was in loading scene to the cutscene removeing Ram blocks,MemTest did a Verifier /standard /all in CMD crashed(got minidump file) HW monitor C* on pc, GPU never came over 65, CPU never over 70 no overclocks Checked Voltages seems to be in range,
use WhoCrashed to read the DMP file.
On Wed 20-01-2016 19:42:35 GMT your computer crashed
crash dump file: C:WindowsMinidump12016-4453-01.dmp
[code]...
This appears to be a typical software driver bug and is not likely to be caused by a hardware problem. The crash took place in a standard Microsoft module. Your system configuration may be incorrect. Possibly this problem is caused by another driver on your system that cannot be identified at this time. URL...
View 1 Replies
Dec 9, 2015
After installing windows 10, most of the time when I boot after the windows logo with circles below it the signal to display stops, if I press reset then the computer boots but the startup is very slow. With windows 8 from pressing the power button I would get to desktop in 8 secs, here it takes at least 30 secs or more. I would like to know the if problem is with windows 10 or Nvidia drivers.
I have Nvidia's 650 Ti boost card.
View 1 Replies
Dec 5, 2015
So I bought a new monitor, the MG279Q and tried plugging it in to my PC via displayport, the monitor comes with a DP->miniDP cable, (from GTX780 DP to monitors miniDP) and the monitor gives no signal. However the computer does recognize the monitor and for example gives the sound alarm for new device attached. I can also see the device describes as "Generic pnp monitor" and I can see it in the Windows's own control panel for monitor + the nvidia control panel (pics in the end). But it won't allow me to set the monitor to use..
I suspected that the cable might be broken so I tested it with my UX32LN (GeForce 840M) laptop which has a miniDP. I plugged it to the monitor (from laptops miniDP to monitors normal DP, the monitor has both DP and mDP) and wow, image straight away. So the cable should be fine I guess.. But this is somewhat of an different situation as I use different port in the monitor compared to my desktops GTX780. And I don't have other computers or gadgets that I could use to test the monitors miniDP port.
Next I plugged in the monitor via HDMI to my desktop and that worked just fine. It recognizes the monitor without problems. Using my old XL2411Z monitor with DVI + MG279Q with DP or the MG279Q with HDMI+DP at the same time I can see the MG279Q being connected twice but it only chooses the HDMI connection and doesn't let me change it to DP even though it shows the connection.
Here are some pics to explain it better:
Multiple panel settings window. It shows the MG279Q on the top (under GTX780 the one not clicked) but it won't let me click it to use. Sometimes it lets me tick it for a second but instantly ticks the box off. The monitor nro 2 is the MG279Q via HDMI.
Surround+PhysX window shows that I've connected the monitor via DP but it is greyed out. It also won't let me make a surround set with the Xl2411z + mg279q DP.
Changing resolution settings only displays the HDMI connected monitor.
So I tried uninstalling the Nvidia drivers + freshly installing them, did not work at all. Neither did uninstalling the generic pnp monitor so the computer would reinstall the displays drivers. I also freshly installed from Win7 Pro -> Win 10 Pro and no difference (was intended to do that later on anyway so I thought that I might check, my laptop is running Win10 and it's DP worked after all). I also went to BIOS and checked that iGPU is disabled + monitor setting is set to PCIE instead of auto, no use. I would also test the GTX780's DP on other desktop computer but I can't. Anyway I'm somewhat suspecting a software/hardware compatibility issue as the monitor is being recognized. Doubt the fact that the monitors miniDP or my graphics cards DP port is broken..
What should I do or try? I really want to run the monitor via DP so I can utilize the 144Hz refresh rate.
Tech specs:
PC: P8Z68-V PRO/GEN3 (bios v3202) + i7 2700K, GTX 780 DC2 (vbios 80.80.21.00.AS04), 4x4GB 1600Mhz DDR3, AX 760 PSU, Win10 Pro
Monitor(s): MG279Q + XL2411Z
View 9 Replies
Feb 10, 2016
I even went to the point going to the configure in Network Adapter Settings > Configure > Ticked off Allowed The Computer To Turn Off This Device To Save Power
It worked For 15 minutes or so, then the Wifi kept on dropping out, I've Restarted and Done All The Router Stuff, That Other Blogs Suggested, Still Nothing, Wifi continuously Drives me insane, now it drops to 2 bars of signal all the time.
I also did ipconfig/ flushdns and that didn't work either, though i was hoping it would, but anyway, I have port forwarded my IP so I can play Mine Craft with my cousin, but other than That, why it just drops constantly in wifi signal all the time.
What I can do to get it staying 5/4 bars signal Strength and not drop when I'm watching Netflix or playing Mine Craft or Battlefield 4 Multi Player. what else I can do, if they need my Wire Less info/name of it, it is
Intel(R) Dual Band Wireless-AC 3160
and yes it is up to date in patches and etc... it worked fine even in Windows 7 Home and Windows 8.1 Home, but as soon as I grabbed Windows 10 Home Update, it just keeps on doing this annoying bug.
View 5 Replies
Mar 5, 2016
when i connect a dvi or hdmi from my gtx 780 to my acer H274HL Monitor all works fine but when i want to connect display port cable on my gtx 780 and the other side is hdmi that goes to my monitor than there is no signal at all.
i am running windows 10 64 bit enterprise and all drivers are up to date also windows updates are up to date.
View 9 Replies
Aug 14, 2015
I've installed Windows 10 on my "new" computer. Everything worked fine.
But my computer won't turn againt. My Monitor says " No Signal Detected "
View 1 Replies
Sep 13, 2015
So I was in my bios and I changed my CPU mode offset sign from + to -, I saved the settings and exited. When the PC restarted it came on perfectly fine but I am getting no signal on my monitor and my razer keyboard & mouse aren't coming on or lighting up.
My motherboard is a P8Z77-V LX
My CPU is a Intel Core i5 3470 3.20Ghz.
My RAM is G.Skill RipJawz 1866mhz 4 X 4
My GPU: Asus GeForce 660ti DirectCU II OC Edition.
I googled around and it said to take the battery out for 10 seconds and put it back in, I did that and no change, I also took the jumper from 1-2 and put it on 2-3 for 10 seconds then back again, Again no change.
Ive reseated the RAM/GPU and CPU and nothing seems to be working.
The pc turns on fine but nothing seems to be working.
Even my Corsair H80i pump LED changed from white to pink which is the colour I set it. All fans are working too.
Why I changed my cpu offset mode, Before this issue I just had a bluescreen for WHEA_Uncorrectable_Error, I turned my PC back on and I googled around and it said it was something to do with my CPU voltage, and one person suggested to try and change it from + or auto to -, So I restarted my PC and changed the cpu offset mode from + to -, after that it doesnt seem to be working and im not quite sure why.
What I can do to try and solve this issue or should I just order a new motherboard?
View 9 Replies
Nov 2, 2015
My printer showing offline, how to switch to online? printer is on and have strong WiFi signal ....
View 1 Replies
