Performance :: 2 Recovery Partitions After Performing Upgrade
Jan 26, 2016
after performing an upgrade, I have 2 recovery partitions, the same size, one at the beginning of the disk and the new one at the end of the disk
I only need one, right?
Two ideas came to mind:
1 boot into linux, copy the contents of the second partition to the first partition, and then delete the second partition.
2 use EaseUs partition master to delete the first partition and then move the second partition to its place.
View 8 Replies
Similar Messages:
Jan 11, 2016
I purchased a Dell Inspiron 15 7000 with a 120GB SSD and a 1TB hard disk. I have the OS on the SSD (C:) together with the programs. So far I have installed Office 365 and little else. I have moved the data directories from C:Users to the D: drive.
The laptop came with no CDs or OS disks and Dell tell me none are available so I have created a recovery USB disk. At the end of that process it informed me that I could now delete any recovery partitions on the boot drive to create extra disk space. On trying this the option failed "Unable to delete partition". The reason for doing this is to recover the drive space used by 3 of the 5 partitions on the SSD. They take up over 32GB of the 120GB I bought. I've never needed to use a recovery partition and would have no issue with having to do a full install from CD or USB in future.
Disk Management does not have a "Delete partition" option for any of the SSD partitions. Would a re-install from the recovery USB stick allow me to delete all partitions on the SSD before re-installing or would they just get created again?
View 9 Replies
Aug 16, 2015
Anyway, today I had to repartition a drive. So, I went into disk management and here is what I found:
My main system drive has 3 recovery partitions! This is after an in-place upgrade, refresh, and then reset.
View 2 Replies
Nov 13, 2015
After finishing the installation of the Threshold 2 update 10586.3, I seem to have grown an additional Recovery Partition.
How many of these do I need?
Will the excess one be deleted along with Windows.old after thirty days (or if I run Cleanmgr earlier)?
View 5 Replies
Mar 5, 2016
I have a Dell Venue 8 Pro with an upgraded Windows 10 installed. Always perform Windows Update but did not pay attention too closely. When the drive space was low and started looking a little bit closer, I found out that I have several Recovery Partitions. From Disk Management display, from left to right are the partitions:
500MB EFI | 40 MB OEM | 490 MB Recovery | C: OS 22.8 GB | 450 MB Recovery | 4.75 GB Recovery
The problem is I do not know which partition that Windows 10 actually created as its Recovery Partition. I do know that the 4.75 GB partition is my original Dell Venue 8 Pro Recovery Partition. Which one can I remove to allow the expansion of my C drive? What gives?
View 9 Replies
Nov 20, 2015
I have upgraded to Windows 10 a few months earlier from Windows 8.1, I have not checked my HDD arrangement after the upgrade. Now I can see that there are two partitions the "system reserved" and "recovery". Where these partitions came from? and Can I get red of them?
View 5 Replies
Sep 30, 2015
I read that a clean install rebuilds partitions and makes a recovery partition.
My question is does it allow you to pick the size of the partition that Windows 10 is installed to ?
I have a 1 terabyte drive but like to install in a 100gig partition.
I think I will delete the existing partitions before I start
View 2 Replies
Feb 2, 2016
I used MicroTool partition manager to delete the extra partitions on an OS drive with win10 (leaving just the main C partition on the drive), and now the laptop will not recognize the SSD with the OS on it, and obviously cannot boot. I also tried using the bootable partition recovery tool from MicroTool, but restoring the partitions also does not work, it will only allow one of the two partitions to be restored.
View 9 Replies
Feb 10, 2016
My laptop running Windows 10 updated to the latest build and would not boot. I kept getting Missing boot manager missing. Eventually I removed the drive and replaced it with my backup clone but that backup is missing a week of a lot of work so I was hooked the original laptop drive to my pc.
Short story, I confused the laptop drive with another disc I a, working on and went into admin tools, storage, and deleted the three partitions on the laptop drive. Since I have tried to recover the partitions with Acronis Disc Manager but the volumes it identifies do not fit. There are three partitions. The primary, the HP recovery and the HP Tools. Total disc is 465GB. The primary partition is 452.
The results I get have seven or eight partitions sizing various sizes between 190 - 350 GB. They all seem to intersect.
i them tried the free EaseUS app which lists multiple versions of every file ever deleted. Is there any easy way to do this?
View 4 Replies
Aug 20, 2015
my question is about Partitions in Windows 10.
I have three-
100MB (created from Windows 7, which I knew was needed for booting)
C Partition (Windows instllation)
450MB (created after upgrade)
So, do I still need the 100MB? and what is this new 450MB used for? Disk Management says that is empty. I don't want to delete anything for risk of making my system unbootable.
View 6 Replies
Nov 20, 2015
I've successfully installed Win 10 on 4 PCs with no problems so far, so I was asked to upgrade one of our office systems from Win 8.1 to Win 10. The unit was an ASUS with Win 8.1 OEM-installed and working, but missing almost all of the available Win 8.1 updates. All else looked good and Win 8.1 was working well. I updated the machine to current 8.1 maintenance level, and the 'Get Win 10' app appeared as expected. I did the upgrade with no problems, but then found that Win 10 Disk Management shows a very large C: partition (Win 10) and 4 small partitions marked 'healthy recovery partition'... and they all show 100% free space and have no drive letters. Right-clicking on those partitions offers no options. Is there no way to get rid of these partitions within Windows? Or will I have to use GpartEd or equivalent? These partitions must have existed before the upgrade because I have not yet created any Win10 backups or recovery disks. I do have the Win 10 ISO files handy, so as a last resort I can do a full drive format and a clean install, but I'm curious about what might be hidden in those mystery partitions.
View 9 Replies
Aug 29, 2015
Just wondering looking at my partitions after upgrading to windows 10 . Do I need to keep the last too partitions? I love windows 10 and had presumed that after a clean install my old windows 8 and 8.1 would be removed are these last too files remainders from them and if so can i delete and how should i do so. Just took a snip of the partitions content!
View 3 Replies
Aug 11, 2015
Recently upgraded to w10 from w8.1 via the upgrade option, then proceeded to make a USB boot with w10 and performed a clean install.
However, something is fishy with my system and w10 so for now i want to revert back to w8.1 via a clean install of w8.1
When i installed w10 however i noticed i have an abundance of partitions, and preferably i would only like to have my SSD and HDD as optional storage spaces. I do of course not want to delete any necessary recovery or system partitions, but to me it seems like i currently have too many.
Which of the partitions in the picture below can i delete? Is it safe to delete all the recovery partitions when clean installing w8.1 from usb? meaning that will the installation create the necessary partitions required by windows?
See picture for info(gjenoppretting = recovery)
View 3 Replies
Dec 7, 2015
Why my monitor screen background flashes when performing functions in Windows 10?
View 1 Replies
Oct 27, 2015
I have tried several times to create a system recovery drive on a USB.
Followed the instructions to the letter, and used two different brand, brand new USB's.
After initial start up it says I need a USB with at least 8 GB capacity, which these USB's have. But nothing happens, it just keeps asking for a USB after one has been inserted.
View 4 Replies
Dec 23, 2015
I have recently updated to Version 1511 and thought I would try to create a recovery drive on a USB having been unsuccessful when trying in the earlier Windows 10. This time it seemed to be working with the system files box checked, though it seemed to take an age before the USB was required to be inserted. It said I would require a USB of 8GB minimum capacity so I used a 16GB size.
When it finished creating the drive ( I did not see the actual finish but no messages were left on screen) I noticed that the USB had only a little over 1 GB of information loaded.
I would probably find it useful if I could be told what files I should expect to find on the USB and the size of each. The files in my USB are titled: boot; efi; sources; bootmgr; bootmgr.efi and reagent. The sources file ( 1GB) is by far the largest.
View 9 Replies
Dec 12, 2015
I recently purchased a new Windows 10 laptop (HP), which I presumed is a 'clean install' and I'm mooching around looking into how to create a recovery disk. Anyway, when I go into control panel, underneath System and Security I see a link that says; Back up and Restore (Windows 7).I'm wondering why there's a reference to Windows 7 on my Windows 10 device?
View 6 Replies
Dec 5, 2015
Just installed a new M.2 SSD into an MSI GE72 laptop running Windows 10. First used MSI's Burn Recovery tool to copy the recovery to a USB flash drive. Restored onto the SSD and wiped the HDD. The resulting partitions on the SSD are shown in the attached image. So I end up with 6 partitions:
1 - EFI Recovery
2 - Hidden Windows partition
3 - C: or first usable partition
4 - 900 MB Recovery partition
5 - D: or second usable partition
6 - MSI's OS recovery image partition
The issue I'm having is that I'd like to collapse partitions 3 and 5 into one large partition for the C: drive. I am unable to do this because of the 900 MB recovery partition between them. Disk Management does not give me any options for this partition. Since I plan on dual booting with Linux installed on a second partition on the HDD, I assume I can use GParted to move the recovery partition to partition 5. I also assume that by doing this, I'll break the recovery function as WinRE is still pointing to partition 4. Also, since I'll then collapse the two usable partitions into one, the partition numbers of that 900 MB partition and the MSI OS recovery partition will change. I'm guessing that there is a way to update the settings but I've run across different forum threads that say the OEM recoveries are custom set up by them. So any generic Windows 10 guides I find may not be applicable.
Of course, I have no basis for a lot of these assumptions as this is my first foray into a Windows OS after Windows 7. Also my first time owning a machine with UEFI, which seems to be fighting against me installing Linux.
I don't understand why MSI would decide to split the large usable partition into two? Even more confused as to why they decided it was a great idea to create an untouchable 900 MB recovery partition in between them?
Maybe also try to convince me how UEFI and Windows 10 is so much better than Windows 7 with a custom recovery in a less than 5 GB custom made recovery partition?
View 4 Replies
Nov 19, 2015
I'm running Win 10 Version 1211 (build 10586.11) - i.e. the latest build with the latest update.
I want to create a new recovery drive but when I get to the window that says "Connect a USB Flash Drive" and the process comes to a dead stop.
-I'm using the same 16GB thumb drive that was previously used to create a Win 8.1 recovery drive so it should be good
-The thumb drive appears in File Explorer and I can read and write to the drive so the system sees it
I should also mention...
-I have attempted this with and without "include system files" checked.
-I find it interesting that after a thumb drive is inserted, I don't have the icon in my system tray that I would normally select to eject the thumb drive.
Nonetheless, I can read and write to the thumb drive. I've inserted the same thumb drives in another computer with Win 10 build 10240 and I get the USB eject icon on my system tray
View 9 Replies
Dec 25, 2015
I am in of a "Free Back/Recovery Program" that is so EASY as pie to understand. I want to backup my pc and also be able to restore and all of this has to be easy for me to run it. I will be backing up onto my external harddrive.I have tried Acronis True Image and to hard to recover back my partitions and etc..
View 9 Replies
Dec 7, 2015
On my HDD there are two partitions, one with Win 7 and one with Win 10, chosen by the Win-Boot-Manager. If I start Win 7 all the recovery points from Win 10 are lost. But starting Win 10 all the "7-points" are still there.
View 5 Replies
Oct 13, 2015
I have upgraded a Win 7 and a Win 8 computers to Win 10. On the Win 7 I used an 8 GB USB Drive for Recovery and it did not use all of the space. On the Win 8 computer I'm getting a message that I need a 32 GB drive. I understand that it may also be backing up my Win 8 information, but 32 GB seems way too much. I hate to waste money on a drive that is not needed.
View 6 Replies
Oct 31, 2015
I upgraded to WIN10 from WIN7. I use Raxco Instant Recovery to make snapshots of WIN10 in this case. I'm on the main snapshot, and I created a copy called the 2nd snapshot, which I can revert to, to save my bacon if need be. I discovered upon completion of updating the main snapshot to the second snapshot, that there were 1,974 errors in the process shown in the log. WIN10 seems to run OK for the most part.
Later I had to boot to the second snapshot because I had a problem with the task bar not responding on two occasions in the first snapshot. After booting in the second snapshot, I copied it to the first snapshot to eliminate the problem, and at the end, it showed 2,125 errors in the log. My question is, if these errors are just crap that migrated during the upgrade from WIN7 to 10 or do you think there are legitimate errors in my WIN10?
View 4 Replies
Dec 4, 2015
I am using a small tablet with Windows on it. It already has little space (32GB which is actually 29 GB), with Windows eating up a ton of space. Now, with a virtual partition on the tablet reserved for system recovery, I have less than 5 GB left, not enough for Windows to update. I would like to merge the virtual partition so as to get ~5 GB extra space, in or to do so I would like to make a recovery disk on a SD-card.
The problem is, Windows does not seem to recognise the SD-card when I try to make a recovery disk! Is there a workaround, or did I get the SD-card in vain?
View 9 Replies
Oct 18, 2015
One of the 1st things I do with a new PC is create & test a recovery drive. This is the 3rd Windows 10 PC I've worked on-all Toshiba Satellites by coincidence. This one seems to have a problem, possibly creating the recovery drive and if not that then certainly using it. Or else I've forgotten how I used it on the other two. I test it by doing a restore from system image-since I create it immediately after completing setup I haven't lost anything and this assures me that if nothing else I can get back to 'ground zero'.
This is the 3rd time I've tried this on the new PC. The first time it said it was unable to create the recovery drive. I checked the USB stick & tried again. That time is 'successfully' created the drive. Both times 'copy system image to recovery drive' was checked. When I tested the 'successfully' created drive it couldn't find a system image on it.
So I'm trying it again and it's just sitting on the 'Please Wait' screen-for 20 minutes so far. Presumably it's erasing the drive so I'm reluctant to simply reboot. And this is the last 16GB USB stick I have. Should I shut it down & try again, get another USB stick, or what? Or have I totally forgotten what I did on the previous 2 PC's that worked?
View 3 Replies
Mar 5, 2016
I created the USB recovery drive successfully with the option "Back up system files to the recovery drive".
Since I needed the USB for another purpose, I transferred the files from the USB to a separate partition on an external HDD and made this drive bootable using YUMI.
So now, on the same laptop, I am able to boot to this new partition on my external HDD where windows recovery environment comes up just fine. I did not want to test the reset or refresh part. Out of curiosity, I clicked on the "System Restore" option on the advanced options screen. I got an error message "To use system restore, you must specify which Windows installation to restore. Restart this computer, select an operating system and then select System Restore"
View 2 Replies
