I have a problem, I installed windows 10 and now I'm stuck in a boot loop after attempting a reset to wipe my files in hopes to make things a little faster, and now I'm unable to do anything other than enter the BIOS.
View 1 RepliesEarlier this afternoon I decided to reset Windows 10 as I had a problem with BSOD BAD_POOL_CALLING over and over again. I booted in Safe Mode, went to Advanced Options and so on. It wasn't a factory-new reset, just the one that removes all files, app data, etc. I left it for a while and came back to find it hadn't worked; there was an error message that read 'There was a problem whilst restarting your PC'. I tried again and the error message appeared again. Because of this, I decided to exit and continue to Windows 10 and see if it had done anything.
Now, when I try to boot my PC up, the circle that usually rotates on the 'Zoostorm' screen when loading doesn't appear. The PC then reboots and tries again, again and again, but with no success. I have tried turning off and on, and even unplugging everything, however nothing seems to work. My PC is now stuck in a continuous reboot loop and won't load. Unfortunately, I can't press F8 or Shift + F8 when booting to start Safe Mode. I have never made a recovery drive for Windows 10 and I don't think my computer came with a repair disk.
I recently upgraded to Windows 10 without a problem, but after a while I thought; why not do a clean install? I went ahead and tried to perform a clean install from the windows 10 settings, and chose all drives, and a quick reset.
It then started the process, after which it crashed with a BSOD telling me something went wrong and that it would restart. After that it kept restarting, sometimes with a BSOD, sometimes just freezing on the windows 10 logo. There were different BSOD errors each time it would crash, I can't remember all of them.
Some of them were along the lines of a driver stack overrun, some were telling me system32/winload didn't exist.
We tried a system restore from USB, but there was no difference. We tried going into the BIOS menu, sometimes it worked, sometimes it froze, and we made sure that the USB would be the first the PC would boot from. Still no difference.
At this point the PC just froze on the windows logo, still trying to initialize the system reset I think. I unplugged the drives and plugged them into my laptop to check what was wrong, and both drives were wiped, with nothing left, no hidden files.
Only with both drives unplugged, the PC would give me something different, an error saying that there is no operating system, which is obvious, so I don't think it's the PC, but windows that is generating this problem.
I tried booting from USB multiple times, with a system restore on it, a windows 10 installation on it, and a windows 8.1 installation on it, since that is what my PC started with.
I am currently an Windows 7 Professional user, and I was seriously considering to jump to Windows 10.
After upgrading, I was thinking in doing a factory reset, in order to try to mimic a clean install of the system. When exploring the options on Internet, I discovered an option to clean de drives completely.
Currently I have 2 drives, my C unit where the OS and most of my software is, and a D drive, in which I have my music, documents, videos and other files not relevant for the system itself.
If I select the options to clean the drives, will it delete both drives or just the C drive?
I recently upgraded my Windows 7 PC to Windows 10 using Windows Update. The whole process was smooth. I never really ran into any problem. Because the PC is so relatively old, I decided to delete all files and reinstall windows 10 using the windows 10 feature 'Reset This PC' to start fresh and theoretically faster. During the reset when Windows is installing my drivers, I noticed that the screen is plain black - no mouse pointer and the amount of reset finished(in percentage) is not also shown. The screen is just plain black. I am pretty sure that both the monitor and CPU is on. I've tried waiting for atleast an hour. I turned my pc's monitor on and off - nothing happened. So I have to resort to hard reset/reboot coz I cannot really see anything on my screen.
When I turned the power of the CPU back, it gave me the error 'The computer restarted unexpectedly or encountered an unexpected error. To install Windows, click ok to restart the computer and restart the installation'. I pressed OK but after restarting, it gave me the same error over and over again. I tried the solution in this website ( during installation of windows | HERESJAKEN), and it got rid of the error. However, I am stuck yet again in a loop that continues to just restart my PC when they reach the screen that tells you how much of the reset is finished, in my case, im stuck at 64% of the reset. That screen is shown for like merely 2 seconds, then the PC will just restart again, then show the "Reset progress screen" again for 2 seconds then PC will just restart again, over and over. I think the only solution is to start the reset of the PC again, but I dont know how.
My installation is stuck in a reset loop. The Win 10 Ready to Install came up, so I clicked Start and it rebooted, back to the login screen, and then Windows Update came up saying it needed to Restart Now. After a couple of minutes the Win 10 Ready screen comes up again. I've rebooted about 20 times and get to the same point every time.
View 2 RepliesI tried to reset my computer today after 3 years of using it without any sort of re-formatting, and all three times the reset got stuck on 65% before a blue screen appeared and said that an error occurred. It would then give me the options of either:
a) returning back to my windows 10, with nothing changed
b) Trying to reset again
c) advanced options.
I tried the reset 3 times, and after the last try failed I went to advanced options to look at other ways to approach the issue, such as checking if there were any restore points that I could restore to (which there were none).
After that didn't work, I clicked on the first option of just returning back to my windows 10, and that was when it would not start up anymore.
My computer now is stuck on a infinite loop of the launch screen of the ASUS logo, it flashes, then goes onto the second ASUS logo, and this is all it does, go round and round.
I tried to boot it on F8, F9 (the ASUS recovery button), and the 'delete' button. NOTHING WORKS.
I finally tried F2, which led me to the BIOS page? And I clicked on the boot tab and disabled the first boot configuration option, and still to no avail. It returned to looping, and when trying F8, F9, after disabling that BIOS option, and it still won't do anything but loop.
i was updating my windows 7 to 10. it was updating smoothly but then my father hard reset the laptop and now my laptop is stuck, it goes to the booting menu. then the "windows error recovery" screen, and when i choose "start windows normally" it shows the logo and says "starting windows" and then it just restarts. how do i solve this? this loop has been going on for the last 2 hours.
View 1 RepliesOk so basically, after successfully installing windows 10 from windows 7, I decided to clean my hard drive and reset windows because I deleted my "edge" and thus my apps were not working. The problem then started, the reset went fine until it reached 64% and read "configuring settings" then it just restarted my PC and went in a loop like this;
>startup
>bios screen (Asus/Intel)
>monitor turns off
>monitor turns back on
>blue win10 logo and loading circle
>black screen for 5-10 secs
>install screen displaying 64%
>restarts and loops
After installing windows 10 on my asus laptop yesterday, last night I tried to wipe my laptop by resetting it, i left it at 1% before i went to bed and this morning it was still at 1% so i did a force turn off and when i turned it back on , it got stuck in a boot up loop where it would just keep on restarting [URL].
Safe mode doesn't work, nothing works, except the power button. What should i do? i didn't want to bring it to asus because the warranty expired 2 months ago.
I built myself a new computer recently and it boots fine if I am booting into the bios. However when booting off my thumbdrive to install windows 10 it boot loops, getting the the windows symbol and then restarting.
My setup specs:
b85m-ds3h-a mobo
pentium g3258 cpu
msi 4gb gtx 960 gpu
hyperx fury 8gb 1866mhz kit
corsair cx500 psu
wd blu 1tb hdd
I was given an error message on reboot and followed a guide to editing the registry to restart the download. The download did not restart however, and my windows 10 is stuck in an endless loop of rebooting. I have downloaded a copy of windows 10 and put it onto a USB, but when I try to boot from USB it takes me back to the BIOS. The BIOS are 'Aptio Setup Utility 2011', and don't seem to allow me to change from UEFI boot to LEGACY boot, although the option is apparently there. Why the USB boot is not working correctly and how to make it do so, I am more than happy to reformat the computer but at this moment in time it's useless. The computer is an Alienware x51 from 2011. As previously mentioned the operating system the PC is trying to boot (or install) is windows 10.
View 4 RepliesI keep getting the "Automatic repair" at boot time and then it diagnoses and later it says it failed.
I've checked several forums now regarding this error, I've tred the following :
1. I tried setting the recoveryenabled to No in using bcdedit. No use.
2. Tried rebulding bcd, No use.
3. Tried resetting by choosing "keep my files" option{Because they are important and I've several programs installed which i don't want to lose).
4. I did chdsk on all drives.
5. Even though I've restore points, it says no restore points found.
I had a virus in my laptop so I reset my laptop to find that it's stuck in the INACCESIBLE_BOOT_DEVICE loop. I don't have any Windows disk to put into my laptop. My laptop is an Asus g750jx.
View 1 RepliesOriginal post [URL] ....
So I force-restarted my computer to hopefully refresh the system but I just got back into the loop. It may be a conflict with some files but for now it's never-ending. What should I do?
The most recent update has bricked my PC and I am stuck on the boot up screen, I have tried pressing F8 on boot up but don't get the option to reset it, what to do?
View 2 RepliesMy pc is unable to start-up after attempting to reset it(fresh reset). It is in a restart loop and when I try to turn it on the Windows 10 logo appears but then a blue screen appears saying "Your PC ran into a problem and needs to restart. We're just collecting some error info, and then we will restart for you." This then lets the PC restart and this restart process happens again. I have tried pressing F8 while it boots up to try to get it into safe mode but had no luck.
View 1 RepliesI'm writing this before having to do a complete wipeout of my system
Specs:
Lenovo Y510p
Hybrid HDD (Seagate) 1TB
m.2 SSD (Trascend) 256GB.
So, since build 9841 I've been using Windows 10 Insider Preview (IP) as my mainly driver. Until the recent redstone builds, Visual Studio has been plagued with problems (From Windows Universal Apps Development to ASP.NET) . I've installed Windows 10 IP in the SSD and have been using it very happily since I've had no major issues, until the ones I've outlined before.
In my Hybrid HDD I had Windows 10 RTM (10586) installed and didn't use it for a quite while (3 months). When these problems rose, I decided to start using that partition again, but out of the blue it decided to start giving me some serious problems: mostly, the whole XAML interface (Start, Volumen, Sound, Battery, etc.) didn't show up. After trying some fixes (From reinstalling Windows Apps to Creating a separate user), I decide to refresh the bits. Unfortunately, even after refreshing my machine didn't fix the XAML interface problems and even worse: I got no possibility to run Universal Apps.
I went and ran some hard disk checkups, from both: the Lenovo Utility and CheckDisk and none threw an error.
The actual problem: Yesterday (Feb. 4) I decide to clean install Windows 10 Build 10586 64-bit in the Hybrid HDD partition (without deleting the OEM reserved spaces) and I'm stuck now on Finalizing the settings. Is there a way to fix it? Tried hitting Shift + F10, but in that specific screen it does not work. In previous screens there are no anomalies.
As last resort I must wipe out everything in both drives and start from zero. I would not like to do that, since Visual Studio is so tough to install (takes too darned long). Is there a way to resort to an alternate method?
Nothing changed, nothing installed. Edge stopped working, Cortana stopped working. Mail stopped working. SFC scannow found corrupt files but unable to fix.Reset keep files and settings failed to boot and rolled back. As did remove everything.Stuck with a very broken PC that is filling logs with everything stopped working and was closed.Just defender installed.
View 9 RepliesI recently screwed up my main HDD through EASEUS as the HDD cannot boot anymore (all files still work fine though)
So instead, I got a SSD and installed Windows 8. Throughout my use, I noticed that on boot, it often conflicts with the corrupted HDD which has Windows 10. Whenever I try to install windows 10, I get an error that my PC needs to be repaired. I assume this is from my corrupted Windows 10.
I checked the BIOS for boot order, but neither my SSD nor HDD is listed, and is instead listed as "Windows Boot Manager". So, how do I disable this corrupted HDD from attempting to boot up?
I attempted an install of Win10 when I first got the go-ahead several weeks ago, it went through the entire install (which took an eternity) and then decided it was incompatible as windows updater encountered errors, it reverted back to 7. Last week I tried again and the pre-install launcher came up with an obscure windows update error, which fixed after downloading and installing the auto-tool for windows updater, but then came up with yet another different error with winupdate.
I restarted, Rand the tool again, and although the window still showed a red X and the same second error , it allowed me to click "retry" which then just force launched the windows 10 migration. I figured might as well, didn't prompt me with any warnings about the potential error so anyways long story short after going ahead, it now freezes on the new logo immediately when it tries to boot the OS, after a couple turns of the progress wheel. Don't know where to go from here and it doesn't seem to be reading any peripherals. Have disconnected and reconnected power and had to force shut down nearly half a dozen times.
The print spooler chokes on both of my Windows 10 machines when trying to deal with certain pdf files. For instance when I tried to print [URL] ... via my browser (Chrome), it printed the first 6 pages, but the printer showed an error when it came to the seventh page. When I then tried to create another job just to print the seventh page, it just hung around in the print spool and nothing happened at the printer.
I tried this several times on two machines. It was also impossible either to cancel the job in the print queue manager or to stop the spooler in the services manager in order to manually clear the print queue, which meant that the only way I could clear the queue was to restart the machine. I got the same behaviour whether I was printing to my physical printer or to the MS pdf printer. I also got the same behaviour when I tried to print from a different browser (Edge). This is not the first time I have had a problem with an unprintable file like this in Windows 10.
When I got on my computer this morning, I was notified of updates. I used the restart button on the notification page thinking this would start downloading the updates. However, the computer has been stuck in Restart for 3 hours. Microsoft... can you access my IP and stop this loop? Is there anything I can do to stop this loop?
View 1 Replies have an Asus Laptop running Win 10, upgraded from win 7. While reading one of the many links from Facebook, using Chrome as a browser, I got a popup that looked like some kind of ransomware . The popup would not close so I turned off the computer.
Now when I turn the computer on it flashes the Asus logo. Then “preparing automatic repair”, “diagnosing your computer” followed by “repairing your computer” appear. It then tells me that the PC did not start correctly and gives me the option to restart or advanced options. Restart brings me back to this point.
Advanced options gives me three options, Turn orr the PC that does that, Exit and continue to Win 10 that gets me back to the previous step or troubleshoot. Trouble shoot gives me the options to reset or more advanced options.
Reset is either a partial or full removal and reinstall or windows. I have some academic software that I do not want to lose if possible and in any case do not have any media to do a Windows reinstall.
The advanced options gives me six choices.
1 System Restore, but there are no restore points found.
2 System image recovery, but I do not have an image disc .
3 Startup repair, starts the process all over and does not find the problem.
4 Command Prompt, appears to open a working command prompt.
5 Startup Settings, Gives me a non clickable list of options but just continues the loop.
6 Go back to previous build. It warns me that I may lose apps and any changes I have made, but not my personal files.
The System is an ASUS laptop, X54C, made in 2012 with Widows 7 Home premium updated to win 10. I have no other access to the computer.
just got new pc and windows 10 with it when i install the windows and everything finishes and restarts. The pc just boots up back to the installation page. Stuck in loop the dam windows wont start up.
View 1 RepliesI have a acer aspire es1 laptop and i upgraded from 8.1 to 10 and when i switch on my computer from cold boot it loads up but when at the login screen it gives the spinning wheel saying hibernating above it but will not go any further.
View 2 Replies