I have Lenovo z580 ideapad, i recently purchased a new sshd and wanted to install windows 10, downloads the file of windows insider preview and copied it to a 32 gb sandisk usb. unfortunately even after setting the bios to usb boot its not booting.
View 1 RepliesI cloned my hard drive a Seagate 2T to a WD 2T using acronics software.I removed my Seagate drive and plugged in my WD drive in the same spot and system would not boot tried using windows 10 repair disk no luck plugged the Seagate drive back in booted???
View 4 RepliesTwo nights ago, I had a brief power outage at my house. Since then, my Windows 10 preview installation will not boot. It keeps giving a boot disk error. I first tried booting from my Build 10166 disc created from ISO and running the startup repair. I've seen errors using this tool on previous Windows versions, but the computer quickly rebooted, so I thought it was successful without errors. Nope, I still get the boot disk error message.
I booted again with my installation disc and tried running the "Refresh" option. This time, I get a message that the drive containing my Windows installation is locked and that I should unlock it before trying again. How I can unlock the drive? Unless I figure that out, it sounds like I will have to perform a clean installation.of Windows 10, which I don't really want to have to do again.
I have a Toshiba Satellite S55-A5294 laptop computer. It is running Windows 10. I had the drive encrypted using Jetico's BestCrypt full disk encryption.
Several weeks ago, I was using Windows, put the computer to sleep, and when I came back an hour later and woke it up, I got the "Preparing Automatic Repair" screen. This was followed by a message that automatic repair was unsuccessful. This problem has happened in the past. In the past, it was the result of a Windows update overwriting the BestCrypt bootloader (BestCrypt encrypts the system partition, so it has to have its own pre-environment password prompt, which can then pass to the mounted system). However, this time it wasn't the case.
As it turned out, I had a corrupted volume. I was able to recover my data. I pulled the hard drive out of the Toshiba computer, put it in a USB enclosure, and connected it to a Lenovo Thinkpad E530, also running Windows 10. In this configuration, I was able to decrypt the drive, and access my data.
I restarted my Lenovo and forgot to disconnect the Toshiba's hard drive. The Lenovo booted right up, into the Toshiba's desktop. I backed up my data, and, for good measure, made a disk image of the whole thing.
I pulled the drive out of the enclosure, and reconnected it to the Toshiba, from which it originally came. When I turn it on, however, I get a BSOD informing me that I have an error:
INACCESSIBLE_BOOT_DEVICE, and the computer then automatically restarts. Upon restart, I receive either the same thing, or a "Preparing Automatic Repair" screen, which then tells me that my computer failed to boot, and suggests a restart. There is also the option for advanced troubleshooting. If I restart, I get locked into the same loop.
I am still able, however, to pull the drive out of that computer, and boot it up when it's attached to my other computer.
I tried connecting the drive to the Toshiba (the original computer from which it came) via the USB enclosure, and I still get the same errors. The Toshiba is able, however, to boot a Linux Live USB.
I know that the drive is bootable. And I know that the Toshiba is willing to boot. They just won't play together.
I ran chkdsk on the system volume, and found no errors. I tried using the Repair option on a Windows 10 installation USB, and didn't really get anywhere.
why the same disk would be bootable on one computer, and not bootable on the other.
I have a dell inspiron 7000 and recently reinstalled windows 10 into my laptop after I received a system thread exception not handled error with a bootable usb. After painstakingly spending a whole day (10 hours) I succeeded in restoring my laptop with windows 10. Nevertheless, I accidentally restarted my laptop while the bootable usb is still in the usb drive and now my laptop does not even load/boot. The screen just freeze trying to load up the OS as in the spinning dots when the windows first loaded up, after 3 dots loaded, the whole screen freezes. in addition, when I try to load up windows repair, it'll load up an extra dot and freezes at 4 loading dots; I can't even load into the hard-drive through BIOS. The good thing is that I can still access the BIOS and do diagnostic test and all the stuff from BIOS. Other than that, I'm unable to access my computer.
View 1 RepliesMy custom-built pc all of a sudden won't boot in to windows. i get the error message "reboot and select proper boot device or insert boot media in selected boot device and press a key", and i have made sure that my hdd is my first boot option. i want to reinstall windows now because that seems like the only way out, but i cant because i have no recovery usb or disc. what can i do to boot to this harddrive, that my bios detects just fine.
View 1 RepliesMy laptop suddenly crashed and now it says "Boot media missing" when I restarted. After that, it always takes me to "Preparing Automatic Repair" and then the 'Troubleshoot' menu.
In the 'Troubleshoot' menu, it has two options: 'Reset this PC' and 'Advanced options'.
When I choose "Reset this PC", it asks me whether to keep my files or remove everything. I've tried both and it displays an error. When I choose to keep my files, it says that drive is locked and tells me to unlock the drive and try again. When I choose to remove everything, it says that there is a problem resetting the PC.
And then I've moved to "Advanced options". The options are: System Restore, System Image Recovery, Startup Repair, Command Prompt, UEFI Firmware Settings, and Go back to previous build. I've tried all of these and it all returned an error. When I chose UEFI Settings, it restarted to BIOS setting. And my BIOS can't detect my hard drive. DISKPART from Command Prompt can't detect it either.
My laptop is running on Window10 efficiently. Sometimes in order to check the DVDs and USBs bootability of newly created OS or Recovery Disk etc I have to select the relative option in the the bios. But on Lenovo G 50 70 the selected option is not permanent. You have to select boot priority option repeatedly for each and every USB/DVD that I want to check. Can i set these option permanently like:-
1st priority USB
2nd priority DVD
3rd priority HDD
4th priority Network IPV4
5th priority Network IPV6
There is a novo key to access the bios in Lenovo Laptop G 50 70.
Problem: When I click on my H: drive or try to access it from the command line, it gives me an access denied error. However, all of the applications that I have installed on that drive run without issue. So, there is some access there. (See attached images. The first shows the hard drive state in diskmanager and in windows explorer. The second image shows the minecrafter launcher profile (that it is stored in H: and the application running, proving that there is some access.
System: Home built PC: (C:) 240GB SSD for OS, (E:) 1TB HDD for file storage and backup, (H:) 1TB HDD for large applications and video editing files. All drives are Simple, Basic, and none have encryption. All use the SATA connectors.
Process: I had Windows 7 Home 64 bit with, among many other things, Comodo Internet Security, Virtualbox, ImageDisk.
During the upgrade process, I noticed that Windows 10, during the upgrade, ran the file system check and fix "problems" on the H: drive.
(Side note) Having forgotten to uninstall Comodo before the upgrade, I did not have network after the upgrade. The fix was non-trivial as I had to use a second computer to download the unofficial comodo uninstaller. Reboot. Uninstall the network devices. Reboot. And once Windows 10 was up and running, it reinstalled the network devices and the network was available.
Still, whether before or after the Comodo uninstall and reinstall, the uninstall of ImageDisk, or the uninstall of the Virtualbox network device, I have no access to the H: drive.
I have a Lenovo laptop upgraded to Windows 10. Last night I switched it off but now when I turn it on, it stucks in the startup Lenovo logo. I think that it is a driver issue but I cannot boot it in safe mode to fix it? What can I do? ( I don't mind to lose my files).
View 2 RepliesI'm making a image for installation of windows 10. I make a USB flash drive with WINPE. and once the device starts into WINPE, it will automatically start to install windows 10 by calling "dism /apply-image". Normally i just shutdown the computer after installation, but now i want to reboot the device and boot into the windows i just installed. But i can't, because if i reboot the device, it will boot into WINPE again and start another turn of installation of windows. How could i temporary boot into my windows 10?
View 4 RepliesPen Drive and external hard drive keep getting errors! So I select to fix the problem scandrive recommended scan and repair. But there's never anything wrong with them it reports! And it takes ages to scan it takes 10-15 minutes for 32GB pen drive. Windows 7 Pro done it in a flash! Anything I can do about it.
View 1 RepliesEver since doing a fresh install of Windows 10, in "This PC", my secondary hard drive is not in the list. I have already tried right clicking "This PC" and clicking Manage -> Disk Management, but there is nothing there except my SSD with Windows 10 installed.
I have tried changing SATA cables, SATA ports, but it still does not appear in This PC. I have also tried installing my hard drive on a another computer to see if the files were corrupted. They were not, all files were still the same before the installation of Windows 10. I did not leave the hard drive plugged in during the installation.
In the BIOS, my computer recognizes both my SSD and my hard drive, but in This PC, it's still missing.
I have had windows 10 since the beta and I recently bought a kingston 120gb ssd I want to do this by reinstalling but since I got windows 10 during the beta with no install disk I have no ability to simply reinstall but how to transfer my license.
View 1 RepliesIn my desktop I have two hard disks ( disk 0 and disk 1 ) . Disk 1 is a clone of disk 0 created by Macrium Reflect
Disk 0 : ( C: ) windows 10 pro , upgrade from windows 7 , ( E: ) windows 8.1 pro , ( G: ) Storage partition
Disk 1 : clone of disk 0
problem description : I see in msconfig / boot a wrong listing
windows 10 ( C:WINDOWS) : Current OS ; Default OS
windows 8.1 pro ( H:WINDOWS ) instead of ( E:WINDOWS )
Nevertheless the dual booting works fine as well as the shift between the disks via BIOS.
The question is , could I fix the situation using the EasyBCD of Neosmart Technologies to edit the bootloader ?
I see can change drive letter H: to E: and save the change , am I right or wrong ? or any other way ....
When I try to boot from a recovery flash drive, it fails with: EFIMicrosoftBootBCD error status: 0xc000000f and message: The Boot Configuration Data for your PC is missing or contains errors.
The recovery flash drive was created on a Lenovo ideapad originally with Windows 8, now upgraded to Windows 10, latest upgrades applied. Checked the box for copying system files. Target drive was a 16GB DataTraveler flash drive formatted as FAT32. Creation ran to completion with no errors. When booting normally, Windows 10 runs fine with no issues. I tried re-creating the recovery drive with the same results.
I created a repair disk and tried to use bootrec to fix the issue, but I suspect it did nothing or fixed the c: drive. I ran boot rec while in the root directory on the flash drive.
I have a legacy 64 bit dual core desktop (ASUS mobo). I have several Sata hard drives in it with the 4th partition of my 1 Terabyte drive containing my Windows 10 Professional boot OS. After converting another similar legacy machine to a NAS device I took the old Windows 10 32 bit OS drive from it and tried booting the ASUS machine with it. Needless to say, the OS didn't like it and reverted to Windows 10 Pro Insider Preview edition (build 11082).
When I tried to restore the boot drive to the original one for this machine the master boot was missing.
I had just formatted another partition on the same drive that had contained a Windows7 installation that had failed. This partition may have contained the master boot record. So I booted to a command prompt from a USB drive and successfully ran the following commands:
bootrec /RebuildBcdbootrec /fixMbr bootrec /fixboot bootsect /nt60 SYSbootsect /nt60 all
After that the BIOS just says "An operating system wasn't found. Try disconnecting any drives that don't contain an operating system" This disk and OS are on the original machine it used to run on. As I understand it, Windows 10 tries to record it's key to somewhere in the BIOS. But the BIOS on these old machines don't provide such a facility. I don't understand what Windows 10 OS does with the key in this instance. If it was recorded in the BIOS then I'd presume that the other Windows 10 drive I attempted to use would have found it and used it. Or perhaps not, since it didn't like the new environment.
what I'm looking for is a way to get my original Windows 10 to boot again on the same machine it had always work on before, from the 4th partition of the 1 terabyte drive I'm using.
I have two hard drive on my PC, as SSD for the OS and a HDD for all my storage.I seem to have a problem with search, that it will only find stuff that is stored on the SDD.To get it to look for other files on the HD, I have to click search my stuff, and even then it still doesn't work.Is there a way to fix this? As most of my stuff is on HD and click search my stuff is a bit annoying.Also when I click rebuild index, nothing happens. I get a dialogue box saying it will take a long time, but then it doest say its indexing
View 3 RepliesMy old computer was a windows 8 that was upgraded to windows 10. I just ordered a new i5 6600 which comes with windows 10, a 250G SSD and 1 TB hard drive.. My old hard drive appears to be a Seagate Barracuda 1TB SATA which seems to be the same as the one in my new Vanquish. My old hard drive is 2/3 full and is backed up often. My question is can I move this old hard drive to my new computer as a separate drive without formatting it and use the data on it (or transfer my data) or does it need to be formatted (thus giving me roughly 2 TB of space with the 1 TB provided with the computer). It was my C: drive in the old computer.
View 8 RepliesIs it possible to do a defragmentation on my PC's hard drive?
View 2 RepliesI have an HP G42-154CA that I'm trying to get Windows 10 Pro installed on.
[URL]
I ran into an issue with the installation disc not detecting the hard drive (ie, no hard drive is listed when the screen appears to select the hard drive to install Windows on).
I've tried various drivers (latest from HP and Intel website, OEM OS installation discs etc) with no luck.. at the very least, the Windows 7 driver from HP's website for that laptop should work for installing Windows 7- same results, does not detect hard drive.
At this point I'm wondering if maybe it's a BIOS setting that's causing this? I don't recall changing anything in the BIOS when I last installed Windows (which was v8), but it was awhile ago, so can't be certain.
Disc cleanup and defraging hard drive after installing W10 and deleting large unwnted files and photos etc.
View 1 RepliesHaven't had to rip lately, thought it was easy, went to play a cd in the player and I can't rip cds in Windows 10 to hard drive. What am I missing? WMP will not allow ripping.
View 2 RepliesSo, I currently have Windows 7 installed in a standard HDD and I bought an SSD a while ago with intentions of reinstalling windows on it. With the Windows 10 update coming in tomorrow, I was wondering if I could install the Windows 10 update on the SSD. Even if it's just installing it on the current HDD I have and then doing a clean install on an SSD. Point is, I want to know if there is any way I can have Windows 10 running on my SSD after tomorrow.
View 1 RepliesSo I just got a new copy of windows 7, with a free upgrade to windows 10. And my question is. If I buy an SSD and install the new OS on that. Can I use my old hard drive for storage such as my steam library and a few applications etc even if it still has the previous OS on it? I know I'd have to set the SSD as my boot drive.
View 1 RepliesI just got an SSD for my Windows 10 PC and wanted to do a full reset of my computer. I tried using the Windows 10 "Reset this PC" feature hoping that it would install on my SSD, but it installed on my old hard drive. Is there a way I could do the reset again and have it install on my SSD or do I have to move my Windows over a different way?
View 1 Replies