Basically I have two drives in my computer that both had windows 10 installed at one point, I removed windows off of one of them and I'd like to remove the drive from my PC entirely, but whenever I take it out windows gives me a message "install valid boot media and restart". What do I need to do so I can remove said drive and keep windows?
(also after that I'm going to install an SSD and copy over windows from the drive I'm not removing if that makes any difference)
Still learning Win 10 ways! I have installed a WD My Book backup drive, and Win 10 gave it the designation of my "G" drive. How do I change from "G" to a different unused letter?
I'm just doing some spring cleaning on my laptop and I noticed a couple of partitions on my hard drive. Well, I'm mostly curious about two. Both of them are about half full. Neither one has a drive letter, and one of them has this label: System. They're allocated but are labeled as unused partitions. What do these partitions do and how careful do I have to be with them? I need to move partitions around and such to merge with and extend my C drive.
The Windows Central Universal Application for Windows 10 Mobile on a Nokia Lumia 830
Since a while i build my own computer, and i put some of my old hard drives in here, one of these drives contains a copy of Windows that i no longer use, But i cant remove it, and it is taking up quite a bit of space, i'm not talking about a Windows.old folder, but an actual Windows folder, now i was wondering if there is a way to remove this unused copy of Windows, i tried changing the owner to myself, and removing the read only tag, without much luck ...
Whenever I try to install a 64 bit Windows 10 copy from a flash drive, I get stuck on the 4 blue squares, with no white dots spinning. Then after about 10 seconds the PC restarts. I have tried the official way with the media creation tool, I have tried just downloading the ISO and using a third party bootable USB maker, I have tried ISO's from pirate sites (yes, I know, not the best solution) but none of those worked. Every time I tried a different method I always fully formatted the USB drive. Oddly enough the 32 bit version worked once or twice but even that doesn't work anymore. My PC specs are quite good so I really don't know what's the issue. Btw im running a 120 GB AData SSD and a 1 TB Seagate hard drive.
I have two drives with files on them and want to make one drive A inactive(remove windows) so that I can make the other drive have windows 10. What is the easiest way to do that without removing or formating Drive A.
In my desktop I have two hard disks ( disk 0 and disk 1 ) . Disk 1 is a clone of disk 0 created by Macrium Reflect Disk 0 : ( C: ) windows 10 pro , upgrade from windows 7 , ( E: ) windows 8.1 pro , ( G: ) Storage partition Disk 1 : clone of disk 0
problem description : I see in msconfig / boot a wrong listing
windows 10 ( C:WINDOWS) : Current OS ; Default OS
windows 8.1 pro ( H:WINDOWS ) instead of ( E:WINDOWS )
Nevertheless the dual booting works fine as well as the shift between the disks via BIOS.
The question is , could I fix the situation using the EasyBCD of Neosmart Technologies to edit the bootloader ?
I see can change drive letter H: to E: and save the change , am I right or wrong ? or any other way ....
When I try to boot from a recovery flash drive, it fails with: EFIMicrosoftBootBCD error status: 0xc000000f and message: The Boot Configuration Data for your PC is missing or contains errors.
The recovery flash drive was created on a Lenovo ideapad originally with Windows 8, now upgraded to Windows 10, latest upgrades applied. Checked the box for copying system files. Target drive was a 16GB DataTraveler flash drive formatted as FAT32. Creation ran to completion with no errors. When booting normally, Windows 10 runs fine with no issues. I tried re-creating the recovery drive with the same results.
I created a repair disk and tried to use bootrec to fix the issue, but I suspect it did nothing or fixed the c: drive. I ran boot rec while in the root directory on the flash drive.
I have a legacy 64 bit dual core desktop (ASUS mobo). I have several Sata hard drives in it with the 4th partition of my 1 Terabyte drive containing my Windows 10 Professional boot OS. After converting another similar legacy machine to a NAS device I took the old Windows 10 32 bit OS drive from it and tried booting the ASUS machine with it. Needless to say, the OS didn't like it and reverted to Windows 10 Pro Insider Preview edition (build 11082).
When I tried to restore the boot drive to the original one for this machine the master boot was missing.
I had just formatted another partition on the same drive that had contained a Windows7 installation that had failed. This partition may have contained the master boot record. So I booted to a command prompt from a USB drive and successfully ran the following commands:
bootrec /RebuildBcdbootrec /fixMbr bootrec /fixboot bootsect /nt60 SYSbootsect /nt60 all
After that the BIOS just says "An operating system wasn't found. Try disconnecting any drives that don't contain an operating system" This disk and OS are on the original machine it used to run on. As I understand it, Windows 10 tries to record it's key to somewhere in the BIOS. But the BIOS on these old machines don't provide such a facility. I don't understand what Windows 10 OS does with the key in this instance. If it was recorded in the BIOS then I'd presume that the other Windows 10 drive I attempted to use would have found it and used it. Or perhaps not, since it didn't like the new environment.
what I'm looking for is a way to get my original Windows 10 to boot again on the same machine it had always work on before, from the 4th partition of the 1 terabyte drive I'm using.
I have Dell Inpiron 3420 Laptop. Windows7 Home Basic was my built-in OS. Now i have upgraded it to Windows10 Home Edition. Now i have left less space in my C-drive. So i want to delete unused files, folders from C-drive. And I also want to backup my windows10 too.
I wasn't sure which forum to put this into. I created a backup image on a usb hard drive. I wanted to be able to restore it using a usb recovery thumb drive. I used the create usb recovery tool and created the recovery flash drive. When I try to boot from the flash drive I get an error saying that the boot configuration data is missing or contains errors. I can boot up the laptop using the current windows install so it isn't referring to the hard drive. I have tried several usb drives and get the same message on each. Here is a screenshot of the message.
My laptop doesn't boot because OS is on E: drive instead of C: drive
When I try to boot it up (it somehow boots up as windows 8.1 instead of my OS windows 10), it gives a BSoD and shows the error code 0xc000021a. I created a bootable USB drive with windows 10 pro on it, but it shows my OS as windows 8.1 instead of 10, and it doesn't allow me to restore or do a startup repair, because they both fail.
I have a Dell 11 venue Pro (7140) tablet and I upgraded to windows 10. My tablet comes with 128Gb and I found out that I have many recovery partition. I am not sure which one I can remove it using DISKPART. Below is what I seen on the Disk Management Screen. Only C drive has volume label of C.
When I was running Windows 7, my system had a small solid state C drive that did not have enough space for windows 10 upgrade. I got a larger 2TB regular hard disk and used the manufacturer's software to clone the old Windows-7 SSD C drive to the new 2TB and then upgraded to Windows 10.
Now under windows 10, when go into defrag, the C Drive shows as a Solid State drive and of course windows does not want to optimize it.
The new drive definitely is not SSD. I assume somehow that setting was cloned from the old disk.
Is there either a way to change the C drive to a regular "hard disk drive" or force windows to defrag what it thinks is a SSD?
I currently have a PC that is running Windows 8.1. I have a 120GB SSD as the primary drive ( C: ) with the OS and a few programs installed on it. I also have a 750GB HDD ( D: ) installed in the computer. Over the past year and a half, I've installed some programs to the SSD and some to a folder on the HDD. I plan on updating this computer to Windows 10. To do that though, I was planning on wiping the SSD and doing a fresh install to it and just reinstalling any programs. My question is if there will be any issues regarding the programs installed on the HDD. I'm guessing some of them probably still have certain files installed on the SSD and that wiping it will mess up those programs.
I'm also wondering what a good way of installing programs to a secondary drive is for the future. I'd like to install some programs to the secondary drive without worrying about certain files still existing on the SSD while still being able to install some programs to the SSD itself. This way if updating in the future, I wouldn't have to worry about this issue. Let me know if this makes sense and if I need to clarify something.
Basically, I plan to disconnect every other Drive from my computer (my 2nd SSD and the HDD I use for data storage). From there, I'd do a clean install of Windows 10 onto my SSD.
Will that SSD become my C Drive by default (I want it to)? Will is stay that way when I reconnect my other drives provided I continue to boot from my SSD?
After cloning a new ssd the new drive won't boot. The bios recognizes it but the only way to get the machine to boot is to connect the old drive. I'm guessing I'll need to try to clone again or maybe install from the back up?
I was trying to boot from the Installation Media with the intent to restore using a system image disk. I have mounted the disk previously and determined that it in fact has the image intact. However it is not recognized. So, I tried to install Windows 10 Home with the Installation Media but there is no partition there and the error says "the drive is locked". I am now typing this on the same pc so obviously there is no problem with the drive.
Since I did clean install of Win 10 I find it will not allow me to boot to internal cd drive or USB drive. I know this is an attempt to secure the OS or lock you out of competing OS like linux or both but I can find no way around this. My bios has not been updated to the secure boot version on purpose but the OS still intercepts any attemp to boot to any device other than drive with OS on it.
My boot sequence is CD first but it is ignored on boot. Also if I go to boot device selection and select CD drive it still boots to win 10. I have tried win 10 setup but there is no option that i have found that allows me to do what I want with my own machine. I am a developer and routinely boot to cd and this behavior is unacceptable. I would like to use win 10 but have gone back to Win 7 until I can find out how to defeat this.
I am currently running on windows 7 home premium and is planning to upgrade motherboard soon. I know that it is possible for me to create a USB boot drive with Windows 10 on it for a new computer. But I don't know if Windows 7 will interfere with Windows 10. I only have 1 hard drive in my system
I have an HP Envy Desktop that boots off the HDD when I bought it, but loads to my PCIe SSD cuz that is where I have windows 10. How do I get it to boot directly on my PCIe SSD? It's an OCZ R4 CM88 1,6TB SSD. The BIOS are set to boot from SSD first, but it continues to boot from HDD as I see the HP logo every time no matter what boot order I select. I tried EasyBCD 2.2 and that didn't work...
So, i am going back to Windows 7 so i have my disc and key. But how to start my computer from the CD drive with windows 10. With Windows 7, there was a key(like F2 or F12) to change boot device. that is not there with Windows 10. So how do i boot my computer from the CD Drive?
I'm trying disgnosis for my Dad, who's trying to move over to SSD.
The story so far: Using AOMEI backupper bootable disk, we tried to clone his current HDD onto the SSD. Part-way through the clone process, it gives an error saying that the drive is too fragmented to clone, and stops.
We run defrag on the C: Drive, resulting in a 1% fragmented drive at the end, and try again.
The same message crops up - too fragmented. It turns out the 'recovery' partition (It's an OEM machine, so its ~10Gb rather than the normal 100Mb) is too fragmented to clone, and we can't defrag it.
So we just clone the C: drive, leaving 1Gb of unallocated space, and then use the recovery DVD's to run startup repair, hoping it will restore the MBR or 'normal' recovery partition, and make the system load. All we get is a blue screen with a blinking cursor in the top left that persists or over 5 minutes.
Startup Repair completes successfully. According to the Log file it ran 2 iterations of the repair operations, and found no errors! However the drive still will not boot.
This is particuarly annoying as I have used backupper both personally and professionally and have NEVER seen the fragmentation issue before, or had any issue at all for that matter with a cloned drive.
I cloned my hard drive a Seagate 2T to a WD 2T using acronics software.I removed my Seagate drive and plugged in my WD drive in the same spot and system would not boot tried using windows 10 repair disk no luck plugged the Seagate drive back in booted???
