I've just built my new PC and am ready to create a system image. However the drive I want to create a system image of is 21gb and I don't have a USB that large. However I do have a hard drive, although that has things on it already so, my question is:Can I put my system image onto a drive that already has things on it or do I need to partition?
View 1 Replies
I've upgraded to 10 from W7, and I've had nothing but problems with it, so i'm concerned about the installation to a different SSD than the one I'm using, my mind is telling me it should be fine as the Upgrade happened all on the same hardware, but changing the location of installation, does that affect activation?
View 6 RepliesI want to do a fresh install of Windows on my new SSD and wipe everything off my current hard-drive. The reason why I want to do this is because my new SSD arrived and my drivers are a little bugged and I want to start over.
[URL] ....
That's the thing I'm going to be using^. I already have it on a CD.
So do I just plug in the SSD, then set the primary boot device to the CD? Then install Windows 10 64-bit to the SSD? That's it?
Also, how am I going to wipe my current hard drive?
Can I use a system image after raiding my hard drives? Or do I need to reinstall everything myself.
View 1 RepliesI recently purchased a Lenovo 900 ultrabook, and proceeded to upgrade from Windows 10 Home to Windows 10 Pro (using a Windows 7 Ultimate product key). Now that I have done this the factory "restore" does not include my upgrade and I am concerned that I would lose it if I ever needed to restore.
So, I am trying to do a full system image backup to a flash drive, but Windows 10 says that the drive is not allowed for this. I can create the USB drive as a network share and get the backup to work using that method, but I don't really trust that it will work properly.
How to do a full system image backup to a USB drive in Windows 10 that you trust will work in the case a restore is needed?
So overall, I was having a issue with creating a system image. It would state that "The specified backup storage location has the shadow copy storage on another volume (0x80780038)"
After reading several forums I found that if you delete the restore points you are able to create a system image.
During my troubleshooting, I was attempting to backup to a 64GBthumb drive (this worked in win8 and win7)..
As I was trying to use the thumb drive, I ran into the following issue..
First it says it needs to be formatted to NTFS. Once I format it to NTFS, it says "The drive is not a valid backup location"
Images I found - [URL] ....
I do not want to use any 3rd party software to accomplish this.
One of the 1st things I do with a new PC is create & test a recovery drive. This is the 3rd Windows 10 PC I've worked on-all Toshiba Satellites by coincidence. This one seems to have a problem, possibly creating the recovery drive and if not that then certainly using it. Or else I've forgotten how I used it on the other two. I test it by doing a restore from system image-since I create it immediately after completing setup I haven't lost anything and this assures me that if nothing else I can get back to 'ground zero'.
This is the 3rd time I've tried this on the new PC. The first time it said it was unable to create the recovery drive. I checked the USB stick & tried again. That time is 'successfully' created the drive. Both times 'copy system image to recovery drive' was checked. When I tested the 'successfully' created drive it couldn't find a system image on it.
So I'm trying it again and it's just sitting on the 'Please Wait' screen-for 20 minutes so far. Presumably it's erasing the drive so I'm reluctant to simply reboot. And this is the last 16GB USB stick I have. Should I shut it down & try again, get another USB stick, or what? Or have I totally forgotten what I did on the previous 2 PC's that worked?
Question; My computer had to be reformatted because of a lock out by a hacker, can I use a restore point that I made before the hack, to restore my files? The restore points and system image are on my back up drive , I restored a couple of files from it. and the folders are there but I do not want to screw things up, as I don't know what I am doing.
View 9 RepliesI have been trying to setup a scheduled backup (Windows 7 Backup and restore) on Windows 10. I want to include a system image of the C: drive as part of the back up and save it to the D: drive. However Windows wont let me save the image on the D: drive, I think because I moved the location of my user files to the D: drive to save space on my SSD.
Any way to override or workaround this without having to move my files back to the C: drive?
I want to create a system image of my primary drive (an SSD) on an external 230gb hard drive as backup for any incovenience.. The problem is my other drive (games,movies, photos, etc) is automatically checked as default because "required for Windows to run" among my primary drive and System Reserved 350MB partition. I cant uncheck its box.
My pc runs windows 10
It' s a custom built pc with:
i7 4770k
GeForce GTX 770 2GB
8gb RAM
230 gb of SSD (primary drive) with still 70gb of free space
1 Terabyte of Hard disk (secondary drive)
230 gb of external TrekStore drive (NFTS formatted)
I was trying to do a system backup on an external hard drive in windows 10 and once it started i noticed that it was creating a backup for my old Windows 7 64 operating system. How do I get it to back up my current Windows 10 system and all of my files on the C: drive.?
View 6 RepliesWhen I built my desktop I plugged a wd green 1tb hard drive so I can copy all of the data from it to my 2 tb green wd
Now I want to unplug that 1tb green hard drive and replace it with a new one? Will that cause system slow? Because windows may thing the drive is still there? No need to clean install again?
Windows 10 Home.
I created system image backup file at least once a week. I did one yesterday, and today I needed to run it to restore my system. To my horror, I cannot find way to run it. I ran system image backup restore multiple times. I know how to do it...... until today. Today, by the time I clicked Troubleshoot option, there is no Advanced Options to choose from. Instead it sent me to Startup Settings option where I could go to safe mode etc,
I ended up running a system restore. Good thing I do create restore point religiously. But, after system restore, I still have the same problem.......... cannot restore image by using system image backup.
adding............... I went to my other laptop running Win 10 Pro, I had no trouble running system image restore.
I want to upgrade to Windows 10, and unfortunatly, the only way for me to do so is by doing a fresh installations and deleting everything, wich I don't want to. I want to back-up my current data on a hard drive partition, if I do a fresh installation of Windows 10, will it delete my partition alongside my data inside it?
View 1 RepliesMy build is unstable and I upgraded... 1st time around and it was for the most part stable. I had some lag issues; when system was left to idle, system would not respond or the system would take forever to perform tasks, and hardware install issues; plug and play pick up and drop. Couple of blue Screens, I run a custom build over clocked and it is my first one so I expected this to happen.
So I decided to do a clean install
System Specs (BUILD):
Motherboard: Asus Maximus VII Formula
Processor: Intel i7-4770K
Memory: (part number)-G.Skill [TridentX] F3-2400C10D-16GTX
Graphics Card #1: SAPPHIRE R9 290 4GB GDDR5
[Code] ....
I have updated motherboard BIOS and rolled them back.
I have manually downloaded new drivers from Asus & AMD websites for 64-bit operating system: Windows 10 as well as let Windows install threw the auto up date program, and full system lockup/crashed are consistent; lock-up none blue screen.
Regional and language match. tch
System says Window is activated.
Ran admin command prompt sfc /scannow with no errors.
On
my probably 13 fresh install config., would really like some insight into what might be happening to cause these system lockup issues, reading and posting on forms from my smart phone isn't the finest thing to do.
I have 3 HDD's (2 internals (1 SSD 120 GB and 1 HDD-Sata 200 GB) and 1 external USB HDD (2 TB)). I have installed Windows 10 Pro x64 final οn the SSD 120 GB without problems and i have installed the extra programs that i use, also without problems. Then i decided to make an image backup to the external USB HDD. The image created succesfully. After that, i have removed the SSD 120 GB, installed the HDD-Sata 200 GB and tried to check to the HDD-Sata 200 GB if the Windows image recovery works. I used the Windows installation DVD and the external USB HDD to do the recovery.
The image recovered normally and the HDD works like as if i was using the SSD 120 GB. So my problem now is with the capacity of the HDD-Sata 200 GB which is shown as 120 GB. So any way to restore the capacity of that HDD again back to 200 GB? I don't want to format the disk now, just continue to use it as a backup disk just in case of failure of my SSD one. I know that i cannot use the HDD Capacity Restore Tool, because it is working only with 32-bit systems (which i currently don't have one right now) and even if i use it i don't know if it will restore my disk to full capacity but in a state that requires format from the begin (something that i am trying to avoid).
So in general, my question is how to restore the capacity of a hard disk after image recovery (when you backup to a new hard disk with capacity bigger than the capacity of the disk that i want to backup).
Is it permitted to install the backup image of Windows 10 to a New bigger hard disk in the same PC. After that I will use the new hard disk only and format the old one.
View 5 RepliesI have been monitoring for several weeks to try and find a pattern. After startup (fresh) or from sleep by Pc works fine for a several minutes or hours then just freezes!! I thought it was the sleep issue but now i notice it does it from a fresh start.
I have also tried using different browsers no different. It can happen when dragging to another monitor but it also happens when doing nothing it just freezes the mouse. I cannot recover i cannot activate Task Manager. I have reboot via pc power button.
I have latest drivers i think also Event viewer report not shutting down properly not sure if that is the crash or what. I keep loosing lots of work I am on.
Problem: When I click on my H: drive or try to access it from the command line, it gives me an access denied error. However, all of the applications that I have installed on that drive run without issue. So, there is some access there. (See attached images. The first shows the hard drive state in diskmanager and in windows explorer. The second image shows the minecrafter launcher profile (that it is stored in H: and the application running, proving that there is some access.
System: Home built PC: (C:) 240GB SSD for OS, (E:) 1TB HDD for file storage and backup, (H:) 1TB HDD for large applications and video editing files. All drives are Simple, Basic, and none have encryption. All use the SATA connectors.
Process: I had Windows 7 Home 64 bit with, among many other things, Comodo Internet Security, Virtualbox, ImageDisk.
During the upgrade process, I noticed that Windows 10, during the upgrade, ran the file system check and fix "problems" on the H: drive.
(Side note) Having forgotten to uninstall Comodo before the upgrade, I did not have network after the upgrade. The fix was non-trivial as I had to use a second computer to download the unofficial comodo uninstaller. Reboot. Uninstall the network devices. Reboot. And once Windows 10 was up and running, it reinstalled the network devices and the network was available.
Still, whether before or after the Comodo uninstall and reinstall, the uninstall of ImageDisk, or the uninstall of the Virtualbox network device, I have no access to the H: drive.
Pen Drive and external hard drive keep getting errors! So I select to fix the problem scandrive recommended scan and repair. But there's never anything wrong with them it reports! And it takes ages to scan it takes 10-15 minutes for 32GB pen drive. Windows 7 Pro done it in a flash! Anything I can do about it.
View 1 RepliesEver since doing a fresh install of Windows 10, in "This PC", my secondary hard drive is not in the list. I have already tried right clicking "This PC" and clicking Manage -> Disk Management, but there is nothing there except my SSD with Windows 10 installed.
I have tried changing SATA cables, SATA ports, but it still does not appear in This PC. I have also tried installing my hard drive on a another computer to see if the files were corrupted. They were not, all files were still the same before the installation of Windows 10. I did not leave the hard drive plugged in during the installation.
In the BIOS, my computer recognizes both my SSD and my hard drive, but in This PC, it's still missing.
Whenever I try to create a system image or run recimg I get error 12289 and the backup fails. System protection is turned on and maximum space used is set to 20%. I have no third party backup software installed and this is a real not virtual machine.
PHP Code:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
- <System>
<Provider Name="VSS" />
<EventID Qualifiers="0">12289</EventID>
<Level>2</Level>
<Task>0</Task>
[code]...
Stop and start VSS servicesDelete old snapshots using vssadmin delete shadows /for=c: /all (there aren't any)Re-register VSS DLLsRe-install 9926.
I successfully created the image to an external drive, apparently. It took some time and the moving activity bar moved to completion.Opening the drive there is no sign of the image altho there is one I created last year. Also altho it said that so much of the drive would be used the resulting free space seems the same as before the creation.It is not in my C drive so what has happened?
View 3 RepliesHow can I check that my system image will work in the case of a crash, Windows 10.
View 3 RepliesI had updated windows 7 home premium to windows 10 then when the update was complete I created a backup image of the whole system.... and saved in an external HD. then my fixed disk died, replaced by a new fixed HD I can not recover the backed up windows ten image from my external HD ... is that due that when replaced the new HD I am contrived to recover the system with windows 7 home premium and windows 7 do not recognize the backed image of windows 10?
View 1 RepliesI created a system image on a Seagate external hard drive using Windows 10 Home, and I created a restore disc for booting with an external BUFFALO DVD drive connected to a USB port. I went into the UEFI and set my BUFFALO drive as the first drive to be used for booting at power up or reset. When I restarted the computer, a message appeared saying "Press any key to boot from CD or DVD". I pressed a key. After a few minutes, the following screen appeared:
I used the down-arrow key to select US and hit enter. Then the following screen appeared:
I used the down-arrow key to select "Choose Device" and hit enter. Then the following screen appeared:
This screen gave me only two options: (1) Boot with the BUFFALO optical drive, and (2) Boot with the Solid State Drive which the HP Spectre x360 has (instead of a real hard drive). When I used the down arrow to select the BUFFALO optical drive, the screen that asks for the desired keyboard layout reappeared. When I selected US and hit enter, the screen that asks for a booting option reappeared. When I selected "Choose Device" and hit enter, the screen that gave me the option to boot with either my BUFFALO optical drive or the Solid State Drive reappeared. I found I could keep going around in circles like this, without ever having an opportunity to restore the computer with a system image I had created earlier.
